Caraudio-Systems z.LiNK ZL-MFD1 User manual

Version 21.05.2010
z.LiNK audio-video-input
ZL-MFD1
Compatible with Audi Navi Plus and VW MFD1
navigation systems (4:3)
AV-input to connect any AV-source to the factory navigation system

Version 21.05.2010 ZL-MFD1
page2
Contents
1. Prior to installation
1.1. Delivery contents
1.2. Checking the compatibility of vehicle and accessories
2. Installation
2.1. Place of installation
2.2. Removal of head unit
2.3. Connecting the interface to the navigation unit
2.4. Activation of the interface as a current AV-source
2.5. Picture settings for the interface
3. Specifications
4. Technical support
Information
Changes of the vehicle software can cause malfunctions of the interface. We offer free
software-updates for interfaces for one year after purchase. To receive a free update, the
interface must be sent in at own cost. Labor cost for and other expenses involved with the
software-updates will not be refunded.
Product features
Plug and play multimedia interface
Audio-Video-input, can be activated by the navigation system
Can be activated by +12V contact alternatively, e.g. rear-view-camera
PAL/NTSC compatible

Version 21.05.2010 ZL-MFD1
page3
Requirements
Vehicle Audi, VW, Skoda, Seat
Navigation Audi Navi Plus navigation system (4:3)
VW MFD1 navigation system (4:3)
Limitation
Factory-TV-tuner must be removed if installed
Retro fit rear view camera switching automatically into reversing gear only possible
for newer MFD1
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
1.2. Checking the compatibility of vehicle and accessories
Take down the serial number of the interface and store this manual for support
purposes: ____________________

Version 21.05.2010 ZL-MFD1
page4
2. Installation
Switch off ignition and disconnect the vehicle’s battery! The interface needs a
permanent 12V source. If according to factory rules disconnecting the battery
is to be avoided, it is usually sufficient to put the vehicle is sleep-mode. In
case the sleep-mode does not show success, disconnect the battery with a
resistor lead.
If power source is not taken directly from the battery, the connection has to be
checked for being start-up proven and permanent.
2.1. Place of installation
The interface is installed on the backside of the navigation.
2.2. Removal of head unit
Unlock the navigation unit and remove it from the
dashboard.

Version 21.05.2010 ZL-MFD1
page5
2.3. Connecting the interface to the navigation unit
•Connect Video-out of the AV-source to the interface box
•Connect Audio-out of the AV-source to the cable harness
Cinch-connections:
YELLOW = VIDEO-input (FBAS-signal)
RED = AUDIO-input right-hand side
BLACK = AUDIO-input left-hand side
•Connect round 10pin-connector of the cable harness to
the round 10pin-female connector on the backside of the
navigation
•Red wire of the cable harness connect to +12V ACC
•Black wire of the cable harness connect to ground
•Green wire of the cable harness +12V= VIDEO ON
if connecting an AV-source:
Audi Navi Plus (all) Connect the green wire
VW MFD 1 (older versions) Connect the green wire, if TV is not selectable
VW MFD 1 (newer versions) NOT connect the green wire
if connecting a rear-view-camera:
VW MFD1 (newer version) Connect the green wire to reverse light (+12V of reverse
light signal) by using a relay
2.4. Activation of the interface as a current AV-source
MFD1 Press AUDIO and select „AV“ (possibly switch the AV-source to “A+V” before)
Navi Plus Press RADIO/CD/TV and select „AV“ (possibly switch the AV-source to “A+V”
before)

Version 21.05.2010 ZL-MFD1
page6
2.5. Picture settings for the interface
The picture settings can be changed on the interface.
For this purpose, the casing must be opened. There
are contact eyes on the PCB which are marked with
"K" for contrast, "F" for colour and "H" for brightness.
Both over and under these contact eyes there are
further contacts, marked with "-" and "+". To change
the respective picture value, the corresponding
middle contact eye and the contact eye with "-" or
"+" must be bridged briefly.
.
3. Specifications
Operation voltage 10,5 - 14,8 V
Max. current consumption ca. 200 mA
Temperature range -30°C to +80°C
Weight 76g
Dimensions (box only) B x H x T 105 x 30 x 78 mm
4. Technical Support
Caraudio-Systems Vertriebs GmbH
manufacturer/distribution
In den Fuchslöchern 3
D-67240 Bobenheim-Roxheim
email [email protected]
Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered
trademarks ® of their corresponding legal owners.