Cardinal 220 User manual

220
WEIGHT INDICATING INSTRUMENT
QUICK SETUP GUIDE
8200-M317-O1 Rev B PO BOX 151 •WEBB CITY, MO 64870 Printed in USA
03/02 PH
(
417
)
673-4631 •FAX
(
417
)
673-5001
http://www.cardinalscale.com

1
TABLE OF CONTENTS
INTRODUCTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 2
FCC COMPLIANCE STATEMENT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 2
SPECIFICATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 3
Certifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 3
SITE PREPARATION REQUIREMENTS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 4
INSTALLATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 5
Mounting the 220 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 5
Load Cell Connection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 5
Load Cell Connections With Over 30 Feet Of Cable - - - - - - - - - - - - - - - - - - - - - Page 6
Load Cell Cable Shield Wire Connection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 6
Serial I/O Cable Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 6
Optically Isolated Inputs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 7
AC Input Relay Board(s) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 7
Preset Weight Comparator/Checkweigher Logic Level Output - - - - - - - - - - - - - - Page 8
AC Output Relay Board(s) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 9
Re-Installing The Rear Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 9
I/O Functions and Relay Box Cable Wire To Relay Number Tables- - - - - - - - - - - Page 10
220 Main PCB (Figure No. 7) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 11
Main PCB Jumpers - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 12
KEYPAD FUNCTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 13
SETUP AND CALIBRATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 15
CALIBRATION "C" NUMBERS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 22
SETUP REVIEW - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 23
TROUBLESHOOTING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 25
Error Codes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 25
Before You Call Service - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 28
CALIBRATION SEAL INSTALLATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 28
EUROPEAN DECLARATION OF CONFORMITY - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 29
SERIAL NUMBER _____________________
DATE OF PURCHASE _________________
PURCHASED FROM __________________
____________________________________
____________________________________
____________________________________
RETAIN THIS INFORMATION FOR FUTURE USE
PRECAUTIONS
Before using this instrument, read this manual and pay special attention to
all "WARNING" symbols:
IMPORTANT
ELECTRICAL
WARNING
STATIC
SENSITVE

2
INTRODUCTION
Thank you for purchasing the Cardinal 220 Weight Indicating Instrument. This instrument was built
with quality and reliability at our factory in Webb City, Missouri.
The 220 incorporates the latest in digital technology and innovative features for the weighing
industry. Configuration and upgrades can easily be performed in the field, while still maintaining
the rigid control the most demanding installations require. This flexibility insures the 220 will be
able to meet your weight indicating needs for years to come.
The purpose of this guide is to provide you with a guide through installation and calibration of your
new weight indicating instrument. Please read it thoroughly before attempting to install your 220
Indicator and keep it handy for future reference.
For complete details on the features, functions and programming of your 220 Indicator, refer to the
220 Weight Indicating Instrument Technical and Operation Manual, 8200-M502-O1.
FCC COMPLIANCE STATEMENT
WARNING! This equipment generates, uses and can radiate radio frequency and if not installed
and used in accordance with the instruction manual, may cause interference to radio
communications. It has been tested and found to comply with the limits for a Class A computing
device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide reasonable
protection against such interference when operated in a commercial environment. Operation of
this equipment in a residential area may cause interference in which case the user will be
responsible to take whatever measures necessary to correct the interference.
You may find the booklet “How to Identify and Resolve Radio TV Interference Problems” prepared by the Federal
Communications Commission helpful. It is available from the U.S. Government Printing Office, Washington, D.C.
20402. Stock No. 001-000-00315-4.
All rights reserved. Reproduction or use, without expressed written permission, of editorial or
pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to the
use of the information contained herein. While every precaution has been taken in the preparation
of this manual, the Seller assumes no responsibility for errors or omissions. Neither is any liability
assumed for damages resulting from use of the information contained herein. All instructions and
diagrams have been checked for accuracy and ease of application; however, success and safety
in working with tools depend to a great extent upon the individual accuracy, skill and caution. For
this reason the Seller is not able to guarantee the result of any procedure contained herein. Nor
can they assume responsibility for any damage to property or injury to persons occasioned from
the procedures. Persons engaging the procedures do so entirely at their own risk.

3
SPECIFICATIONS
Power Requirements: 90 to 264 VAC (50/60 Hz) at 0.4A
Enclosure Type: NEMA 4X/IP66:
Enclosure Size: 10 7/8"W x 8 3/16"H x 3 1/8"D (276mm W x 208mm H x 79mm D)
Weight: 9.2lbs (
Size and Weight DOES NOT include Gimbal )
Operating Environment: Temperature: 14 to 104 ºF (-10 to +40 ºC)
Humidity: 90% non-condensing (maximum)
Display: 12-digit, 0.8" high, 14-segment LCD
Transducer Excitation: 12 VDC
Signal Input Range: 1.0 mV min. to 40 mV max. (with dead load boost)
Number of Load Cells: 14 each, 350 OHM minimum resistance
Load Cell Cable Length: 1500 feet maximum with sense lines.
30 feet maximum without sense lines
Maximum Displayed
Weight Value
9,999,999
Division Value: 1, 2, or 5 x 10, 1, 0.1, 0.01, 0.001 and 0.0001 commercial
0 to 99, non-commercial
Sensitivity:
NON-COMMERCIAL
NTEP
CANADA
OIML
0.15 uV/e
0.3uV/e (Class III/IIIL)
0.3uV/e (Class III/IIIHD)
0.7 uV/e (Class III)
Scale Divisions:
NON-COMMERCIAL
NTEP
CANADA
OIML
100 to 240,000
100 to 10,000 (Class III/IIIL)
100 to 10,000 (Class III/IIIHD)
100 to 10,000 (Class III)
Internal Resolution: 1 part in 16,777,216
Tare Capacity: Six Digits (999,999)
Sample Rate: 1 to 100 samples per second, selectable
Auto Zero Range: 0.5 or 1 through 9 divisions
Weighing Units: Tons, Pounds, Metric Tons, Kilograms, Grams, Ounces, Custom
Keypad: Membrane type with 27 color-coded keys
Standard I/O: (1) Bi-directional RS232 and 20mA
(1) RS232/20mA output only
(1) Infrared (IR) Data Port
Optional I/O: 14 bit Analog Output (0 to 10v, 4 to 20mA)
Certifications:
This equipment is certified to comply with the requirements for a Class III/IIIL device by the
• National Conference on Weights and Measurements (Certificate No. 01-011)
• Measurement Canada (Approval No. AM-5397)
• and for a Class III device by OIML R-76 (Certificate No. DK 0199.47).
Consult factory for
other requirements

4
SITE PREPARATION REQUIREMENTS
The 220 Weight Indicator is a precision weight measuring instrument. As with any precision
instrument, it requires an acceptable environment to operate at its peak performance and
reliability. This section is provided to assist you in obtaining such an environment.
Electrical Power
The 220 indicators has been designed to operate from 90 to 264 VAC at 50/60 Hz. Note that a
special order is not required for operation at 230 VAC.
CAUTION! - To avoid electrical hazard and possible damage to the indicator,
DO NOT, under any circumstance, cut, remove, alter, or in any way bypass the
power cord grounding prong.
On models requiring 230 VAC power, it is the responsibility of the customer to have a qualified
electrician install the proper power cord plug which conforms to national electrical codes and local
codes and ordinances.
The power outlet for the indicator should be on a separate circuit from the distribution panel. This
circuit should be dedicated to the exclusive use of the indicator. The wiring should conform to
national and local electrical codes and ordinances and should be approved by the local inspector
to assure compliance.
To prevent electrical noise interference, make certain all other wall outlets for use with air
conditioning and heating equipment, lighting or other equipment with heavily inductive loads, such
as welders, motors and solenoids are on circuits separate from the indicator. Many of these
disturbances originate within the building itself and can seriously affect the operation of the
instrument. These sources of disturbances must be identified and steps must be taken to prevent
possible adverse effects on the instrument. Examples of available alternatives include isolation
transformers, power regulators, uninterruptible power supplies, or simple line filters.
Environmental
In general, the 220 Indicator will perform well within a
temperature range of 14 to 104 °F (-10 to +40 °C ).
In order to keep cooling requirements to a minimum, the
indicator should be placed out of direct sunlight and to
provide adequate air circulation, keep the area around the
indicator clear.
Make certain the instrument is not directly in front of a
heating or cooling vent. Such a location will subject the
indicator to sudden temperature changes which may result
in unstable weight readings.
Insure that the indicator has good, clean AC power and is
properly grounded.
In areas subject to lightning strikes, additional protection to
minimize lightning damage, such as surge suppressors,
should be installed.
CAUTION! When in parallel runs, locate Load Cell cables a minimum of 24" away
from all AC wiring.

5
CAUTION! Disconnect any external load cell power supply before connecting load
cells to the instrument. Failure to do so will result in permanent damage to the
instrument.
INSTALLATION
Before beginning installation of your Model 220 Weight Indicating Instrument, make certain that the
instrument has been received in good condition. Carefully remove the instrument from the
shipping carton and inspect it for any evidence of damage (such as exterior dents or scratches)
that may have taken place during shipment. Keep the carton and packing material for return
shipment if it should become necessary. It is the responsibility of the purchaser to file all claims for
any damages or loss incurred during transit.
Mounting the 220
NOTE! Should your 220 indicator come already installed on a scale, the following information
describing the installation of the instrument does not apply.
The Model 220 Indicator is housed in a NEMA 4X/IP66 stainless steel wall or desk-mount
enclosure. The 220 gimbal may be mounted on a desktop or other smooth, flat, horizontal surface
or may be mounted on a wall. Refer to Figure No. 1 for a layout of wall-mounting bolts.
6.00"
Figure No. 1
If wall mounted, make certain the mounting surface is strong enough to support the instrument.
The mounting location should be where the display is easily viewed while being close enough to
provide the operator easy access to the keypad. Carefully lay out the mounting hole locations,
then drill and install the anchor bolts. Attach the gimbal to the wall and securely tighten the
retaining bolts.
Load Cell Connection
1. Remove the 14 acorn nuts securing the
back panel to the main housing, then
loosen the bottom-right cable gland
connector for the load cell. This gland
connector is located on the rear panel
of the enclosure. Refer to Figure No. 2
for illustration of the connector layout.
2. Slip the single cable from the load cell
or load cell junction box through the
gland connector and into the enclosure.
3. Remove 2" of the outer insulation
jacket then remove 1/4" of insulation
from each of the 4 wires and shield
without sense leads or 6 wires and Figure No. 2
shield with sense leads (refer to Figure
No. 3).
Clearance for
#10 size screw

Load Cell

6
4. Connect each of the wires to terminal block
P6 referring to the table on the circuit board
for terminal connections. Refer to Figure
No. 7 for terminal block location.
5. To terminate a wire, first press down on the
release bar for the terminal, insert the wire
into the terminal opening then allow the
release bar to return to its original position,
locking the wire in place.
6. Repeat the procedure until all of the wires
are in place.
7. Route the load cell cable through the two Figure No. 3
cable clips provided on the upper and left
sides of the enclosure interior.
LOAD CELL CONNECTOR P7
PIN NO. Function PIN NO. Function
1 + EXCITATION 5 - SIGNAL
2 + SENSE 6 - SENSE
3 + SIGNAL 7 - EXCITATION
4 SHIELD
Load Cell Connections With Over 30 Feet Of Cable
For installations with over 30 feet of cable between the indicator and the load cells, sense wires
should be used. The sense wires must be connected between the +SENS, -SENS terminals on the
indicator and the +EXCITATION, -EXCITATION wires of the load cells or the +SENS, -SENS
terminals of the load cell trim board or the section seal trim board. For the indicator to use the
sense wires, the +SENS jumper J12 and the -SENS jumper J13 must be open (see Figure No. 7).
Load Cell Cable Shield Wire Connection
The load cell cable shield wire should be connected to the
threaded stud inside the indicator. This stud is located on
the bottom inside of the indicator near the load cell
connector P7. See Figure No.4.
The shield wire should be wrapped around the stud
between the 2 flat washers and secured using the hex nut.
Figure No. 4
Serial I/O Cable Installation
The 220 may be connected to a printer to record weight and associated data or it may be
connected to a remote display or even to a computer for transmission of weight data. The
weight data may be transmitted on demand (pressing the PRINT key or on receipt of a
command from the computer). For complete details on the 220 Serial I/O, refer to the
Setup, SIO Serial I/O section of the 220 Weight Indicating Instrument Technical and
Operation Manual, 8200-M502-O1.
1. Loosen the cable gland connector(s) for the serial cable. The gland connector(s) for the
serial data are located on the rear panel of the enclosure. Refer to Figure No. 2 for an
illustration of the gland connector layout.
2. Slip the serial cable through the gland connector and into the enclosure.
Threaded Stud for
Shield Wire

7
3. Remove 2" of the outer insulation jacket then remove 1/4" of insulation from each of the
wires (refer to Figure No. 3).
4. Connect each of the wires to the Serial I/O terminal block (P10) referring to Figure No. 7 for
terminal block locations.
5. To terminate, first press down on the release bar for the terminal, insert the wire into the
opening then allow the release bar to return to its original position, locking the wire in place.
Repeat the procedure until all of the wires are in place.
BI-DIRECTIONAL SERIAL INTERFACE SERIAL OUTPUT
PIN NO. Function PIN NO. Function
1 TXD 1 - SRC 8 RXD 1 - RS232
2 TXD 1 - 20 mA + 9 TXD 1 – CTS
3 TXD 1 - 20 mA - 10 GND 1
4 RXD 1 - SRC 11 TXD 2 - 20 mA Active
5 RXD 1 - 20 mA + 12 TXD 2 - RS232
6 RXD 1 - 20 mA - 13 GND 2
7 TXD 1 - RS232
Optically Isolated Inputs
Included with the I/O are 7 programmable inputs that may be used to remotely (up to 100 feet)
initiate various functions within the indicator. These inputs are accessed via a terminal block (P9)
on the back of the PC board (see Figure No. 7). The 7 inputs are defined as follows:
PIN NO. Function PIN NO. Function
1 + SRC 6 Not Used
2 ZERO 7 STOP
3 TARE 8 START
4 GROSS / NET 9 DUMP
5 PRINT 10 GND / SHIELD
Remember that the input must be connected to Gnd to initiate the function.
AC Input Relay Board(s)
The AC Input Relay Board(s) are mounted in an external junction box for use with the 220
Indicator. The RB4-IN (115 VAC) or RB4-INV (230 VAC) contain one board and supports 4 inputs
(jumper selectable). The RB8-IN (115 VAC) or RB8-INV (230 VAC) contain two boards and
supports 7 inputs. The relay board used in the 115 VAC version is Cardinal p/n 8200-C324-0A.
The 230 VAC version uses relay board Cardinal p/n 8200-C324-1A. Connect the devices as
shown in Figure No. 5.
• INPUT (IAC-5) ……….. 90 to 140 VAC @ 6mA maximum for each plug-in relay.
• INPUT (IAC-5A) ……... 180 to 280 VAC @ 6mA maximum for each plug-in relay.
• OUTPUT ..…………..... 5VDC @ 12mA from the 220 main pc board assembly P9.
• CONNECTION ............ Removable plug-in screw terminals for up to 14 AWG wire.

8
AC Input Relay Board(s)
NOTE! AC INPUT RELAYS ARE VOLTAGE DEPENDENT. A DIFFERENT RELAY IS
REQUIRED FOR 115 VAC AND 230 VAC!
Preset Weight Comparator/Checkweigher Logic Level Output
If you so choose, you may use the logic level outputs from your Model 220 indicator’s preset
weight comparators or checkweigher to control peripheral devices used to manage the flow of
material or signal when the weight is within preset limits. Note that these outputs are at logic level
and cannot drive external devices directly. Solid state relays can be used to accept the logic level
output from the 220 and in turn, drive the external device.
To connect the control cable to the preset weight comparator/checkweigher logic level output
connector P8, first loosen a gland connector located on the back of the 220. Refer to Figure No. 2
for the location of the connectors. Slip the cable through this connector and into the enclosure.
Remove 2 inches of the cable insulating jacket then 1/4 inch of insulation from each of the internal
wires (refer to Figure No. 3). Make the proper terminations on terminal block P8. To terminate a
wire, first press down on the terminal block release bar, insert the wire into the terminal and
remove pressure from the release bar locking the wire in place.
Figure No. 5

9
AC Output Relay Board(s)
The AC Output Relay Board(s) are mounted in an external junction box for use with the 220
Indicator. The RB4-OUT contains one board and supports 4 outputs (jumper selectable). The
RB8-OUT contains two boards and supports 8 outputs. The relay board used in both is (Cardinal
p/n 8539-C062-0A). Connect the devices to be controlled as shown in Figure No. 6.
The individual relays can be configured to be on (closed) or off (open) at weights under the preset
weight then switch at the preset weight from on-to-off or off-to-on by setting the under weight
condition to on or off during setup and calibration or setup review.
• OUTPUT (closed) ........ 28-240VAC @ 3A maximum for each plug-in relay.
• CONTROL INPUT ....... 5VDC @ 12mA from the 220 main pc board assembly P8.
• CONNECTION ............ Removable plug-in screw terminals for up to 14 AWG wire.
NOTE! All relays are the normally-open type that will open when power to indicator is lost.
Re-Installing The Rear Panel
After all terminations have been made, remove the excess cable from the instrument enclosure
and securely tighten each of the cable gland connectors. Do not over-tighten these connectors but
make certain they are snug. DO NOT USE TOOLS! Finger tighten only! Ensure any unused
gland connectors are plugged. Replace the rear panel and secure with the 14 acorn nuts removed
earlier. NOTE! Follow a diagonal pattern when tightening the acorn nuts.
Figure No. 6

10
Main PC Board I/O Functions Table
INPUTS OUTPUTS
PWC CHECKWEIGHER DFC BATCHER
P9 INPUTS P8 Presets Check 3 Check 5 Fill 1 Fill 2 Batch 1 Batch 2
2 ZERO 2 PWC 1 Under Under Fill Fast Fill 1 Fast 1
3 TARE 3 PWC 2 Accept Lo Under Slow Fill 2 Slow 1
4 Gross/Net 4 PWC 3 Over Accept Fill 3 Fast 2
5 PRINT 5 PWC 4 Lo Over Fill 4 Slow 2
6 N/A 6 PWC 5 Over Fill 5 Fast 3
7 STOP 7 PWC 6 Fill 6 Slow 3
8 START 8 PWC 7 Fill 7
9 DUMP 9 PWC 8 Dump Dump Dump Dump
Refer to Figure No. 5 for the AC Input Relay board, Figure No. 6 for the AC Output Relay board
and Figure No. 7 for the Main PCB.
Relay Box Cable Wire Number To Relay Number Table
CABLE WIRE
NUMBER
RELAY NUMBER
(Set Proper Jumpers)
2 1
3 2
4 3
5 4
6 5
7 6
8 7
9 8
10 +SRC
(For AC Input Relays)
1 GND
The relay box cable wire numbers correspond to the indicator main PC board remote input and
output connnector pins (P9 and P8).
EXAMPLES:
INPUT
If cable wire number 2 is connected to P9-2, then AC Input relay 1 or 5 (depending on the
relay board jumper setting), will initiate a “zero” function on the indicator.
OUTPUT
If cable wire number 2 is connected to P8-2, then PWC 1 will activate AC Output relay 1 or 5,
depending on the relay board jumper setting.
DFC OPERATION WITH A SINGLE RELAY BOARD
DFC operation can be accomplished using one relay board. By setting the relay board
jumpers on PWC1, PWC2, PWC3 and PWC8 (see Figure No. 6), PWC1 will operate relay 1
at the Fill preset, PWC2 will operate relay 2 at the SLOW preset and DUMP will operate
relay 4 with the dump command (see the tables above). Note, that PWC3 is not used.

11
CAUTION! This device contains static sensitive components. Improper handling can
result in damage to or destruction of the components or card. Such actual and/or
consequential damage IS NOT covered under warranty.
Figure No. 7
SERIAL I/O P10
GND2 13
TxD2-RS232 12
TxD2-20mA
ACTIVE 11
GND1 10
TxD1-CTS 9
RxD1-RS232 8
TxD1-RS232 7
RxD1-20mA- 6
RxD1-20mA+ 5
RxD1-SRC 4
TxD1-20mA- 3
TxD1-20mA+ 2
TxD1-SRC 1
J6 AUTO-ON
J7 TEST
J8 8V EX
CALIBRATION
SWITCH J6
P2
P3
13
P10
1
10
P9
1
J11
P5
IIC
10
P8
1
ISP
P6
J15
6 J13
J12
P7
J14
1
J12 + SENS
J13 - SENS
J14 GND TO
CHASSIS
J15 DEAD LOAD
BOOST
LOAD CELL P7
- EXC 7
- SEN 6
- SIG 5
SHLD 4
+ SIG 3
+ SEN 2
+ EXC 1
J7
J10
P4
J8
8200 - 0300 - 00
U31
REMOTE
INPUTS P9
GND/SHLD 10
DUMP 9
START 8
STOP 7
- - - - - 6
PRINT 5
GROSS/NET 4
TARE 3
ZERO 2
+SRC 1
REMOTE
OUTPUTS P8
GND/SHLD 10
PWC 8 9
PWC 7 8
PWC 6 7
PWC 5 6
PWC 4 5
PWC 3 4
PWC 2 3
PWC 1 2
+SRC 1
J10 ACTIVE REMOTE
OUT
J11 ACTIVE REMOTE
IN

12
Main PCB Jumpers (See Figure No. 7)
J6 - AUTO-ON JUMPER
The AUTO-ON jumper J6, when connected, will cause the indicator to power on automatically
whenever power is applied to the power input connector. If power is lost momentarily and then
reapplied, the indicator will turn on without pressing the ON key. See Figure No. 7 for jumper
location.
J7 - TEST JUMPER
The TEST jumper J7, when connected, will turn the backlight on, disregarding the LIGHT ON=
setting (refer to Setup Review for explanation of LIGHT ON). See Figure No. 7 for jumper location.
J8 - 8V EX JUMPER
The 8V EX jumper J8, when connected, allows the 220 indicator to supply 8 VDC excitation
voltage when a remote (external) 12 VDC battery is used to power the indicator. To operate from
the 12 VDC battery, the load cell excitation voltage MUST be set to 8 VDC (J8
closed ). Operating
with the load cell excitation voltage set to 12 VDC will result in an unstable weight display. See
Figure No. 7 for jumper location.
J10 - ACTIVE REMOTE OUT JUMPER
The Active Remote Out jumper J10, when connected, allows the 220 indicator to supply (source)
5 VDC to a solid-state relay or other load of 200 ohms or greater. To operate from the 5 VDC
source, the positive connection from the relays must be connected to P8 pins 2 through 9 and the
negative wire from the relays to P8 pin 10 (GND/SHLD). See Figure No. 7 for jumper and
connector P7 location.
For completely isolated outputs, J10 must be open (positioned on one plug-in pin only or removed)
and the user must provide 5 to 12 VDC to P8 pin 1 (+SRC) and a ground return to the load. The
load must still be 200 ohms or greater. Note that P8 pin 10 (GND/SHLD) is not connected.
J11 - ACTIVE REMOTE IN JUMPER
The Active Remote In jumper J11, when connected, allows the 220 indicator to supply (source)
5 VDC to a remote input circuit. Connecting P9 pins 1 through 9 to P9 pin 10 (GND) through a
switch will cause the selected action. See Figure No. 7 for jumper and connector P9 location.
For completely isolated inputs, J11 must be open (positioned on one plug-in pin only or removed)
and the user must provide 5 to 12 VDC to P9 pin 1 (+SRC) and a ground return to the switch
connected to P9 pin 2 through 9. Note that P9 pin 10 (GND) is not connected.
J12 AND J13 - SENSE JUMPERS
If the sense leads are NOT used, you must install plug-in jumpers at J12 and J13 adjacent to the
terminal block. These jumpers attach the sense leads to the excitation leads. If sense leads ARE
used (as in motor truck scales), these plug-in jumpers should be positioned on one plug-in pin only
or removed and stored for later use. Refer to Figure No. 7 for the location of the jumpers.
J14 - GND TO CHASSIS JUMPER
This jumper when installed connects the analog circuit ground to the indicator chassis ground.
Refer to Figure No. 7 for the location of the jumper.
J15 - DEAD LOAD BOOST JUMPER
For very low dead loads (less than 10% of the combined load cell capacity) connect the dead load
boost jumper J15 on the printed circuit board. Refer to Figure No. 7 for the location of the jumper.

13
KEYPAD FUNCTIONS
The following describes the keys and their functions as used during setup and
calibration. For complete details on the 220 Indicator keypad functions, refer to the
220 Weight Indicating Instrument Technical and Operation Manual, 8200-M502-O1.
ON/OFF (K) KEY
This key is used to apply and remove power to the indicator. In the alphanumeric mode, it is used
to enter the letter “K”.
0 THROUGH 9 (P THROUGH Y) KEYS
These keys are used to enter numeric data during setup and calibration. The 1 and 0 are also
used to answer yes (1 = YES) or no (0 = NO) to various prompts. In the alphanumeric mode, they
are used to enter the letters “P” through “Y”.
✱ASTERISK KEY
During Setup, when a setup parameter is displayed, pressing this key will "backup" to the previous
prompt. Pressing this key during entry of data will toggle the keypad to the “alpha” mode. It is also
used in conjunction with the other keys on the keypad to access additional indicator functions.
ENTER (Z) KEY
The ENTER key is used to signal completion of the entry of data and causes the indicator to
process the data entered. When reviewing setup parameters, pressing the ENTER key will display
the current setting of the parameter. In the alphanumeric mode, it is used to enter the letter “Z”.
ZERO/REVIEW (A) KEY
Pressing this key after the ASTERISK key will enter the Review mode of Setup and Calibration.
Refer to the Setup Review section of this guide for details. In the alphanumeric mode, this key is
used to enter the letter “A”.
TARE (B) KEY (WITH DIAMOND "T" SYMBOL)
In the alphanumeric mode, this key is used to enter the letter “B”.
NET/GROSS (C) KEY
In the alphanumeric mode, this key is used to enter the letter “C”
TARE (D) KEY (WITH WEIGHT "T"SYMBOL)
In the alphanumeric mode, this key is used to enter the letter “D”.
UNITS/TEST (E) KEY
Pressing this key after the ASTERISK key will enter the Test mode and conduct a test of all display
elements. The test consists of 12 cycles, each lasting about one second:
1. The model number and the software version are displayed.
2. All alphanumeric characters and annunciators will turn on.
3. The calibration numbers (C1 to C4) are displayed.
In the alphanumeric mode, this key is used to enter the letter “E”.
START/STOP (F) KEY
In the alphanumeric mode, this key is used to enter the letter “F”.
MEM (G) KEY
In the alphanumeric mode, this key is used to enter the letter “G”.

14
ID (H) KEY
In the alphanumeric mode, this key is used to enter the letter “H”.
ACCUM (I) KEY
In the alphanumeric mode, this key is used to enter the letter “I”.
DELETE (J) KEY
In the alphanumeric mode, this key is used to enter the letter “J”.
COUNT/SAMPLE (L, §) KEY
Pressing this key during entry of alphanumeric data will
backspace and delete the last character
entered. In the alphanumeric mode, it is used to enter the letter “L”.
TIME/DATE (M, CAPS) KEY
This key is used to enter the clock mode to program the time, date and consecutive number. In
the alphanumeric mode, it is used to enter the letter “M” and to toggle between lower and upper
case alpha characters.
12 Hour Format Selected In Setup (TIME=12)
1. If the time displayed is correct, press the ENTER key and proceed to step 3.
2. If the displayed time is incorrect, enter the correct time and press the ENTER key.
3. The display will show AM=XX, where XX is the current setting. If the time is before noon
(12:00 PM), press the 1/YES key (display will show AM=YES), then press the ENTER key.
4. The display will show DATE=XX.XX.XX, where XX.XX.XX is the current date.
5. If the date displayed is correct, press the ENTER key to proceed to the CNC NO= prompt.
6. If the date displayed is incorrect, enter the correct date and press the ENTER key to
proceed to the CNC NO= prompt. Remember to enter the date in the same format (month-
day-year or day-month-year) as selected by the USA setup parameter.
24 Hour Format Selected In Setup (TIME=24)
1. If the time displayed is correct, press the ENTER key and proceed to step 3.
2. If the displayed time is incorrect, enter the correct time and press the ENTER key. Note that
with the 24 hour format selected, entering all times after noon (12:00 PM), you must add 12
to the time, i.e. 3 PM would be 1500.
3. The display will show DATE=XX.XX.XX, where XX.XX.XX is the current date.
4. If the date displayed is correct, press the ENTER key to proceed to the CNC NO=.prompt.
5. If the date displayed is incorrect, enter the correct date and press the ENTER key to
proceed to the CNC NO= prompt. Remember to enter the date in the same format (month-
day-year or day-month-year) as selected by the USA setup parameter.
Consecutive Number (CNC NO=)
If the consecutive number displayed is correct, press the ENTER key. If the consecutive
number displayed is incorrect, enter the correct number (6 digits max.) then press the ENTER
key to resume normal operation.
PRESET (N, SPACE) KEY
This key is used to enter the weight values for the Preset Weight Comparators (PWC), the
Checkweigher feature or the Digital Fill Control feature depending on which function was selected
during setup and calibration. In the alphanumeric mode, it is used to enter the letter “N” or to insert
a space between characters.
PRINT (O) KEY
In the alphanumeric mode, this key is used to enter the letter “O”.

15
SETUP AND CALIBRATION
Your 220 indicator has been thoroughly tested and
calibrated before being shipped to you. If you
received the indicator attached to a scale,
calibration is not necessary. If the indicator is
being connected to a scale for the first time or
recalibration is necessary for other reasons,
proceed as indicated.
The calibration switch is located on the enclosure
rear panel. You may gain access to this switch
simply by removing the calibration switch access
screw on the rear panel. Refer to Figure No. 8.
Figure No. 8
During the setup and calibration process it is necessary to enter operational parameters via the
220's keypad. Pressing the ENTER key without entering a new value will retain the current
setting and advance the 220 to the next prompt. To change a setting, enter a new value and
press the ENTER key. This will save the new value and advance the 220 to the next prompt.
Pressing the ASTERISK key will "backup" to the previous prompt or return to normal operation.
CAUTION: The membrane keypad is not to be operated with pointed objects
(pencils, pens, fingernails, etc). Damage to keypad resulting from this practice will
NOT be covered under warranty.
Enter Setup Mode
To enter the setup mode, with the indicator ON, insert a small screwdriver or other tool through the
calibration switch access hole on the rear panel. Press and release the calibration switch. The
menu SETUP will be displayed. Continue to press and release (or hold) the switch to rotate through
the beginning point for entering the setup mode.
SETUP Setup Mode (starts at USA= prompt)
ANALOG Analog to Digital Filtering (starts at FILTER= prompt)
CALIBRATE Calibration (starts at CAL WT 1= prompt)
SERIAL Serial Input/Output (starts at BAUD 1= prompt)
PRINT TABS Print Tab Settings (starts at PORT= prompt)
FINE SPAN Fine Span Adjustment
HIGH RES Display High Resolution Weight Mode
KEY LOCK OUT Key Lock Out Function
ANALOG OUT Analog Output Option (If option board is installed, Calibration
of 10 volt or 4 to 20 mA Analog Output)
If you press the ENTER key at the SETUP prompt, you may proceed through to the next section (up
to and including FINE SPAN) by pressing the ENTER key.
NOTE! Setup may be interrupted at any time. ALL data previously entered and
finalized with the ENTER key will be retained in the non-volatile memory.
Pressing the calibration switch at any prompt will return you to the SETUP menu. To exit setup,
press the ASTERISK key with any of the above menu selections displayed or cycle power at any
time (press the ON/OFF key twice).
Calibration Switch
Access Screw

16
SE TUP – Setup Function
If setup is desired, press the ENTER key, otherwise press the cal switch to advance to A-D?.
USA (
YES = Domestic, NO = International)
LFT (
YES = Interval of 1, 2, 5, 10, 20 or 50, NO = Interval 1 to 99)
BASE UNITS (
0= none, 1= tn, 2= g, 3= lb, 4= oz, 5= kg, 6= tonnes)
CONVERTED UNITS (
0= none, 1= tn, 2= g, 3= lb, 4= oz, 5= kg, 6= tonnes, 7= custom)
If you selected 7 = custom
CNVF = Conversion Factor
LABEL = Label
MODE OF OP
0 = Basic Indicator
1 = ID Storage
ID COUNT (1= One Prompt, 2= Two Prompts, 3= Three Prompts)
NOTE! The value selected for ID COUNT will determine the number of
additional prompts displayed following the ID COUNT prompt.
PROMPT 1 (Prompt 1 Name,12 Characters Alphanumeric)
PROMPT 2 (Prompt 2 Name, 12 Characters Alphanumeric)
PROMPT 3 (Prompt 3 Name, 12 Characters Alphanumeric)
2 = Digital Fill Control
SPEED (1= Single, 2= Two Speed)
If (SPEED =1), advance to AUTO TRIM=
If (SPEED =2),
GATE SEQ (1= AB then B, 2= A then B)
AUTO TRIM (YES = Auto Trim ON, NO = Auto Trim OFF)
AUTO PRNT (YES = Auto Print ON, NO = Auto Print OFF)
MULT DROP (
YES = Enabled, NO = Disabled)
DUMP GATE (
YES = Enabled, NO = Disabled)
If DUMP GATE = NO, advance to DCUMLATE =
If DUMP GATE = YES,
AUTO DUMP (
YES = Enabled, NO = Disabled)
DCUMULATE (
YES =Weigh Out, NO = Weigh In)
AUTO TARE (
YES = ON (Net Fill), NO = OFF (Gross Fill)
3 = Preset Weight Comparators
OUTPUTS (Allowable values are 1through 8or 11 through 18)
1 Low State before cutoff with 1 active Preset
2 Low State before cutoff with 2 active Presets
3 Low State before cutoff with 3 active Presets
4 Low State before cutoff with 4 active Presets
5 Low State before cutoff with 5 active Presets
6 Low State before cutoff with 6 active Presets
7 Low State before cutoff with 7 active Presets
8 Low State before cutoff with 8 active Presets
11 High State before cutoff with 1 active Preset
12 High State before cutoff with 2 active Presets
13 High State before cutoff with 3 active Presets
14 High State before cutoff with 4 active Presets
15 High State before cutoff with 5 active Presets
16 High State before cutoff with 6 active Presets
17 High State before cutoff with 7 active Presets
18 High State before cutoff with 8 active Presets
Relay*
Open
Relay*
Closed

17
3 = Preset Weight Comparators, Cont.
The relay state is based on using Cardinal Scale relays (p/n 6850-1013). If
using relays other than those supplied by Cardinal Scale, refer to the relay
manufacturers specifications. NOTE! When power to the indicator is lost, the
output returns to a Low State condition.
If OUTPUTS= 2 through 8 or 12 through 18, advance to WT RANGES=
If OUTPUTS= (1 or 11)
BAL PRNT (YES = Enabled, NO = Disabled)
4 = Checkweigher
OUTPUTS (Allowable values are 3or 5)
If OUTPUTS = 3 (All are Low State before cutoff (Relay* Open))
Over
Under
Accept
If OUTPUTS = 5 (All are Low State before cutoff (Relay* Open))
Over
High-Accept
Accept
Low-Accept
Under
The relay state is based on using Cardinal Scale relays (p/n 6850-
1013). If using relays other than those supplied by Cardinal Scale, refer
to the relay manufacturers specifications. NOTE! When power to the
indicator is lost, the output returns to a Low State condition.
AUTO PRNT (YES = Auto Print ON, NO = Auto Print OFF)
5 = Batcher
SPEED (1= Single, 2= Two Speed)
If (SPEED =1), advance to AUTO TRIM=
If (SPEED =2),
GATE SEQ (1= AB then B, 2= A then B)
AUTO TRIM (YES = Auto Trim ON, NO = Auto Trim OFF)
BIN COUNT (Allowable values are 1through 7)
If SPEED=1, up to 7 bins are available.
If SPEED=2, a maximum of 3 bins are available.
AUTO PRNT (YES = Auto Print ON, NO = Auto Print OFF)
DUMP GATE ( YES = Enabled, NO = Disabled)
If DUMP GATE = NO, advance to DCUMLATE =
If DUMP GATE = YES,
AUTO DUMP (YES = Enabled, NO = Disabled)
DCUMULATE (YES =Weigh Out, NO = Weigh In)
WT RANGES (1= Single Interval, 2= Dual Interval)
If WT RANGES = 1 advance to the INTERVAL.
If WT RANGES = 2
LOW INT
If LFT=YES (Allowable values are: 1, 2, 5, 10, 20 or 50).
If LFT=NO (Allowable values are: 1through 99).
LOW DPP (Allowable values are 0, 1, 2or 3).
0 = XXXXXX 1= XXXXX.X 2 = XXXX.XX 3 = XXX.XXX

18
If WT RANGES = 2 (Dual Interval), Cont.
LOW RNG= (Allowable values are: 1through 9,999,999).
HI INT=X
If LFT=YES (Allowable values are: 1, 2, 5, 10, 20 or 50).
If LFT=NO (Allowable values are: 1through 99).
HI DPP
(Allowable values are 0, 1, 2or 3).
0 = XXXXXX 1= XXXXX.X 2 = XXXX.XX 3 = XXX.XXX
INTERVAL
If LFT=YES (Allowable values are: 1, 2, 5, 10, 20 or 50).
If LFT=NO (Allowable values are: 1through 99).
DPP (Allowable values are 0, 1, 2or 3).
0 = XXXXXX 1= XXXXX.X 2 = XXXX.XX 3 = XXX.XXX
CAP (Allowable values are: 1through 9,999,999).
Z TRACK (Allowable values are: 0(disables Zero Tracking), 0.5, or 1through 9).
Z LIMIT (YES = 5% scale capacity, NO = Full Capacity, no limit).
PUO (YES = Auto Re-Zero on Power-Up, NO = No Re-Zero on Power-Up).
TIME (12 = 12 hour clock (3PM displays 3:00).
(24 = 24 Hour Clock, (3PM displays 15:00).
CLR TARE (YES = Clears Store Tare when Net Weight goes below Zero).
(NO = Stored Tare
is not cleared when Net Weight goes below Zero).
CLR ID (YES = Automatically clears ID after print)
(NO = ID
is not cleared after print).
ANALOG? - Analog to Digital Filtering
If analog to digital filtering setup is desired, press the 1/YES key, then the ENTER key.
Otherwise press the ENTER key to advance to CALIBRATE?.
FILTER (Allowable values are: 0= disabled, 1= minimal, 2= moderate or 3= custom).
If FILTER = 0, 1, or 2 advance to the SAMPLES.
If FILTER = 3
F= (Filter level, allowable values are 0to 255).
B= (Break range, allowable values are 1to 255).
SAMPLES (Allowable values for the sample rate are: 1through 100).
STABLE (Motion detection, allowable values are 0through 99 divisions).
STBL CNT (Consecutive Stable weight readings, allowable values are 1through 255).
CALIBRATION? - Calibration
If calibration is desired, press the 1/YES key, then the ENTER key. Otherwise press the
ENTER key to advance to SERIAL?.
If the indicator was calibrated previously and the four calibration “C” numbers were recorded,
you may enter the “C” numbers instead of using test weights. Please note that if the scale is
used in a commercial application and must be "Legal for Trade", the "C" numbers can not be
used to re-calibrate.
ENTERING CALIBRATION “C” NUMBERS
1. With
CAL WT 1=displayed, press the "diamond T" TARE key.
2. The display will show C1=XXX.
3. If the
C1= number displayed is acceptable, press the ENTER key.
4. Otherwise, enter a new
C1= number, then press the ENTER key.
5. Repeat steps 2 through 4 for C2=, C3= and C4=.

19
CALIBRATION? - Calibration, Cont.
CAL WT 1 - FIRST CALIBRATION WEIGHT
The display will show CAL WT 1=0.
Two Point Calibration:
This is the first of two calibration weights. This weight could be ZERO (NO LOAD) or the
TEST WEIGHTS / TEST LOAD.
Three Point Calibration:
This is the first of three calibration weights. This weight could be ZERO (NO LOAD), the
TEST WEIGHTS / TEST LOAD or the MID-POINT WEIGHT .
• If the first calibration weight is to be ZERO (NO LOAD), press the ENTER key.
• If the first calibration weight is to be the TEST WEIGHTS / TEST LOAD or MID-POINT
WEIGHT, use the numeric keys to input the value of the calibrated test weights.
• Place the weights on the scale platform, then press the ENTER key.
• Starting at the left and proceeding right, a series of dashes will appear on the display.
• The dashes will stay on the display momentarily, then disappear, after which the display
will show: CAL WT 2.
CAL WT 2 - SECOND CALIBRATION WEIGHT
The display will show CAL WT 2=0.
Two Point Calibration:
This is the second of two calibration weights. This weight could be ZERO (NO LOAD) or
the TEST WEIGHTS / TEST LOAD.
Three Point Calibration:
This is the second of three calibration weights. This weight could be ZERO (NO LOAD),
the TEST WEIGHTS / TEST LOAD or the MID-POINT WEIGHT .
• If the second calibration weight is to be ZERO (NO LOAD), press the ENTER key.
• If the second calibration weight is to be the TEST WEIGHTS / TEST LOAD or MID-
POINT WEIGHT, use the numeric keys to input the value of the calibrated test weights.
• Place the weights on the scale platform, then press the ENTER key.
• Starting at the left and proceeding right, a series of dashes will appear on the display.
• The dashes will stay on the display momentarily, then disappear, after which the display
will show: CAL WT 3.
CAL WT 3 - LAST CALIBRATION WEIGHT
The display will show CAL WT 3=0.
Two Point Calibration:
This weight is not used. Press the ENTER key to skip and advance to SERIAL?.
Three Point Calibration:
This is the last of three calibration weights. This weight could be ZERO (NO LOAD), the
TEST WEIGHTS / TEST LOAD or the MID-POINT WEIGHT .
• If using 3 point calibration and the last calibration weight is to be ZERO (NO LOAD),
press the ENTER key.
• If using 3 point calibration and the last calibration weight is to be the TEST WEIGHTS /
TEST LOAD or MID-POINT WEIGHT, use the numeric keys to input the value of the
calibrated test weights.
• Place the weights on the scale platform, then press the ENTER key.
• Starting at the left and proceeding right, a series of dashes will appear on the display.
• The dashes will stay on the display momentarily, then disappear, after which the display
will show: SERIAL?.