Carman AUTO-i 100 User manual

-1-
1. DLC LED: Communication with a vehicle
2. Bluetooth LED: Bluetooth communication
3. USB LED: Communication with a USB port
4. PWR LED: External power supply. (12V DC, DLC power supply)
5. Power connector: It is for a AC/DC power adaptor and a cigar jack.
6. USB B TPYE: Connecting to PC for USB communication &update.
7. RS232: It connects to TPMS module for read sensor data and coding.
8. Serial No. label.
※Program files in the USB stick
1. “SETUP_AUTO_i100_XXX_APP.EXE”: AUTO-i100 Diagnostic program installation file
2. “SETUP_Repair.exe” for Repair Information Folder: Repair Information data file
3. “AUTOi_USB_Driver.exe” for SetUp Driver Folder
: USB driver installation program file for Module and PC USB connection
4. “AUTO-i Series User Manual.pdf” for User Manual Folder: User Manual
AUTO-i100 User Manual

-2-
Basic kit
AUTO-i100 Module Extension DLC Cigar LightPower USB Cable Bluetooth Dongle
USB Stick Carrying Case
Asian kit
Kia 20P(Blue) Mazda “C” 17P Kia/Mazda Daewoo/Gm Ssangyong 14P
Ssangyong 20P Samsung/Nissan14P Mitsubishi(12+16P) Subaru 9P Hyundai/Mitsubishi
Toyota(17R) Toyota (17C) Honda 3P Honda 5P
European
kit
Audi/VW (2+2P) BMW 20P Benz 38P BenzCable(3 Liner) Opel 10P
PSA 2P FIAT 3P
Australian
kit.
Ford 20P Holden 6P

-3-
Installation of Mini Bluetooth Setting(User Manual Page80~83)
* You are able to install all program of AUTO-i 100 in regular sequence with running the provided USB Flash Memory.
If you want to setthe Bluetooth only, please follow installation procedure below.
1. Click “Devices” on [SETTINGS]
2.Select “Bluetooth”
-> Select “AUTO-i Device Serial Number” ->“Pair ”
3. Input Passcode (0000) -> Next 4. Completed Pairing
5. Run “AUTO-i Diag” Program and Click “CONFIG”. 6. Select Device (AUTO-i100), Connection Method
(MINIBLUETOOTH), and Input Serial No. -> Save.
7. Check a location of diagnostic connector on a car.
- If your car uses OBD-
II, most diagnostic connector is
located between a handle and a brake pedal.
- If your car is old one, not supporting OBD-II, it requires a
additional connector. Check a proper connector among what
we supplies. Location of the connector may be different
according to car models.
8. Connect the AUTO-i 100 to a diagnostic connector on your
car directly. If your car supplies power to AUTO-i 100, PWR
light on the front side of the AUTO-i 100 will be turned on.
If so, you do not need to connect power cable.

-4-
Precautions For Use
The AUTO-i 100 described in this guide was manufactured for those who havethe basic knowledge
required for its use.
Users should follow the safety instructions described in this manual for safe andefficient use of the product.
Safety regulations for overall use are as follows.
Power Source
- Do not touch power cords with wet hands. (It may result in an electric shock.)
- Do not use the product under electrically unstable conditions. (It may result in damage to a power supply unit.)
- Push down the plug until it clips securely into place. (Otherwise, it may result in a fire.)
Wireless Communication
- Avoid high tension currents or electronic jamming. (It could be affected by external environment)
- AUTO-i 100 Module includes its Bluetooth module inside.
Blue-color LED displays its Bluetooth connection status of AUTO-i 100 Module.
- For stable Bluetooth connection, please use a private Bluetooth Module and PC device.
Usage
- Do not drop the product. (It may cause damage to the product.)
- Do not put the product on a distributor.Although manufactured to prevent interference of internal
electromagnetic wave, any strong interference beyond the set limitmay result in damage to the product.
- Do not attempt to repair, disassemble, or alter the product yourself. (It may cause damage to the product.)
- Avoid air-vent plugged by foreign substances. This may cause fire or damage of product.
Upgrade
- Never attempt to disassemble the USB Cable. (It may cause damage to the product.)
Storage and Carriage
- Avoid storage in a humid place. (It may cause damage to the product.)
- Use the carrier bag provided with this product when carrying. (It will protect the product from external impacts.)