Carrier EU-OSK105 User manual

CONTENTS
DECLARATION OF CONFORMITY
SPECIFICATION...............................................
PRECAUTIONS ...............................................
DOWNLOAD AND INSTALL APP....................
INSTALL THE SMART KIT...............................
USER REGISTRATION ...................................
NETWORK CONFIGURATION.........................
HOW TO USE APP............................................
SPECIAL FUNCTIONS......................................
1
2
3
4
5
6
7
8
1
1
2
3
4
6
17
19
Hereby, we declare that this Smart kit is in
compliance with the essential requirements and
other relevant provisions of Directive 2014/53/EU.
A copy of the full DoC is attached.
(European Union products only)

1
1
SPECIFICATION
Model: EU-OSK105,US-OSK105
Standard: IEEE 802. 11b/g/n
Antenna Type: Printed PCB Antenna
Frequency Band: 2400-2483.5MHz
Operation Temperature:0 C~45 C/32 F~113 F
Operation Humidity: 10%~85%
Power Input: DC 5V/300mA
Maximum TX Power: <20dBm
Please keep you APP up to date with the latest version.
Due to special situation may be occurred, we explicitly
claims below: Not all of theAndroid and iOS system
are compatible with APP. We will not be responsible
for any issue as a result of the incompatibility.
W
Cautions
ireless safety strategy
Smart kit only support WPA-PSK/WPA2-PSK
encryption and none encryption .
WPA-PSK/WPA2-PSK encryption is recommended.
Due to different network situation, control process
may return time-out sometimes. If this situation
occurs, the display between board and App may not
be the same, please do not feel confused.
Smart Phone camera needs to be 5 million pixels or
above to make sure scan QR code well.
2PRECAUTIONS
Applicable system: iOS, Android.

3
WARNING
4
INSTALL THE SMART KIT(wireless module)
Remove the protective cap of the smart kit
(wireless module)
Open the front panel and insert the smart kit
(wireless module) into the reserved interface.
Insert
Attach the QR code packed with Smart kit
(wireless module) to the side panel of the
machine, ensure it is convenience to be scanned
by the mobile phone.Alternatively, user can take
picture of the QR Code and save it into their own
phones.
1
2
3
:This interface is only compatible with
SMARTKIT(wireless module) provided by the
manufacturer.

4
VI5
0
Fo
5USER REGISTRATION
Please ensure your mobile device is connected to
Wireless router. Also, the Wireless router has already
connected to Internet before doing user registration and
network configuration.
It is better to log in your email box and active your
registration account by clicking link in case you forget
the password. You can log in with the third party accounts.
1Click "Create Account
Android iOS
"
cc

2Enter your email address
and password, and then
click " "Register
5

6
6NETWORK CONFIGURATION
Cautions
Kindly reminder:
It is necessary to forget any other around network and
make sure theAndroid or iOS device just connect to
the Wireless network you want to configure.
Make sure theAndroid or iOS device Wireless function
works well and can be connected back to your original
Wireless network automatically.
User must finish all the steps in 8 minutes after powering on
air conditioner, otherwise you need to power on it again.
Note:
Using Android or iOS device to do network
configuration
There are two ways to finish the network configuration:
Network configuration by Bluetooth scan
Network configuration by select appliance type
Make sure your mobile device has already been
connected to the Wi-Fi network which you want to use.
Also, you need to forget other irrelevant Wi-Fi network
in case it influences your configuration process.
Disconnect the power supply of AC.
Connect the power supply of AC, and continuously press
the “LED DISPLAY” or “DO NOT DISTURB” button seven
times in 10 seconds.
When the AC displays “AP”, it means that the AC Wi-Fi
has already entered into “AP” mode.

7
Network configuration by Bluetooth scan
Note: Make sure the bluetooth of your mobile device is
working.
Press “ + Add Device ” Press “Scan for nearby
devices”
12