Casablanca Veneto User manual

1
P/N C1543001 HN1209
Safety and the proper operation of your Casablanca fan both require a thorough knowledge
of the product and proper installation; therefore, before attempting to install and operate your
Casablanca fan, read this owner’s manual completely and carefully. Retain this manual for
future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off
at the circuit breaker or fuse box before attempting any installation procedure.
Veneto™Owner’s Manual
READ AND SAVE THESE INSTRUCTIONS!
CONTENTS
Parts List __________________________________________________________________________3
Introduction _______________________________________________________________________5
BeforeYou Start ................................................................................................................................................ 5
Safe Use ............................................................................................................................................................ 5
Mounting Recommendations .......................................................................................................................... 6
Sloped Ceiling Installation ............................................................................................................................... 6
Fan Installation ____________________________________________________________________7
Getting Started.................................................................................................................................................. 7
Mounting Bracket Installation.......................................................................................................................... 7
Pipe Scroll Hardware........................................................................................................................................ 8
Pipe Scroll Assembly........................................................................................................................................ 8
Upper Glass Assembly....................................................................................................................................10
Hanging the Fan...............................................................................................................................................10
Wiring ............................................................................................................................................................... 11
Securing the Canopy.......................................................................................................................................13
Blade Installation .............................................................................................................................................14
Light Kit Installation.........................................................................................................................................15
W-74 Wall Control Preparation........................................................................................................................16
W-74 Control Installation _________________________________________________________ 17
Installing the W-74 Wall Control......................................................................................................................17
Single W-74 Installation...................................................................................................................................17
Dual W-74 Installation......................................................................................................................................18
W-74 Operation __________________________________________________________________ 19
Operation Power..............................................................................................................................................19
Operation Speed Control ................................................................................................................................19
Operation Reversing Airow ..........................................................................................................................19
Operation Lights ..............................................................................................................................................19
Changing Frequency Setting ......................................................................................................................... 20
Operation CFL Mode ...................................................................................................................................... 20
Automatic Demonstration Program.............................................................................................................. 21
Operation Safe-Exit®...................................................................................................................................... 21
Light-minder® Program ................................................................................................................................. 21
Operation Fan-Minder™ Program................................................................................................................. 22
Operation Home-Safe® Program ................................................................................................................. 22
Troubleshooting Tips _____________________________________________________________ 23
Care Recommendations __________________________________________________________ 24
Product Specications ___________________________________________________________ 24

Parts List
If you are in need of service parts, do not return this fan to the store.
21
20
22
23
26
25
24
33
30
7
4
8
5
12
13
15
16
14
Parts List
Model # C15G624L
Asm. Dwg. # 98093-06
Finish Bullion Black
Item # Item Name Qnty Part #
19 Hanging System 1 99411-10-000
42 Hardware Pack C 1 G0151-03-000
20 Wood Screw #10 2
21 Wood Screw #8 2
22 Washer 4
23 Screw, 10-32 4
24 Ceiling Plate 1
25 Canopy 1
26 Trim Ring 1
10 Receiver 1 89346-02-000
32 Hardware Pack A 1 G0151-03-000
6 Pipe Assembly 1 87942-19-624
29 Hardware Pack B 1 G0150-01-000
30 Set Screw (Pre-Installed) 1
33 Screw #8-32 3
35 Scroll Kit 1 G0153-01-000
36 Screw, Ball 3
37 Shaft Collar 1
38 Screw #6-32 3
39 Downrod Scroll 3
4 Finial 1 76402-01-624
41 Glass Cover 1 76899-01-624
5 Light Kit 1 88134-01-000
40 Glass Set 1 G238
7 Glass Shade, Upper 1
8 Glass Bowl, Lower 1
9 Blade Badge 5 88123-05-624
17 Blade Screw Kit 1 89440-14-000
18 Blade Iron 5 98079-05-624
28 Blade Set 1 G0113-27-000
27 Blade Iron Screw Set 1 G0111-01-000
11 Wall Control Assembly 1 89350-02-000
12 W74 Dual Control 1
13 Décor Wall Plate (White) 1
14 Wire Nut 4
15 Screw 6-32 X .75 2
16 Screw 6-32 2
2 Screwdriver, Phillips 1 65567-01-000
39 Allen Wrench 1 64801-01-232
1 Balancing Kit 1 65520-01-000
3 Light Bulb E12 C7 (15W) 6 76323-01-000
31 Candelabra Bulb (40W) 3 77646-07-000
41
42
PARTS LIST

Veneto ™
Call our Support Center toll free at 1-888-227-2178
10
6
38
36
37 39
9
18
28
27
39
2
31
3
32
Parts List
Model # C15G624L
Asm. Dwg. # 98093-06
Finish Bullion Black
Item # Item Name Qnty Part #
19 Hanging System 1 99411-10-000
42 Hardware Pack C 1 G0151-03-000
20 Wood Screw #10 2
21 Wood Screw #8 2
22 Washer 4
23 Screw, 10-32 4
24 Ceiling Plate 1
25 Canopy 1
26 Trim Ring 1
10 Receiver 1 89346-02-000
32 Hardware Pack A 1 G0151-03-000
6 Pipe Assembly 1 87942-19-624
29 Hardware Pack B 1 G0150-01-000
30 Set Screw (Pre-Installed) 1
33 Screw #8-32 3
35 Scroll Kit 1 G0153-01-000
36 Screw, Ball 3
37 Shaft Collar 1
38 Screw #6-32 3
39 Downrod Scroll 3
4 Finial 1 76402-01-624
41 Glass Cover 1 76899-01-624
5 Light Kit 1 88134-01-000
40 Glass Set 1 G238
7 Glass Shade, Upper 1
8 Glass Bowl, Lower 1
9 Blade Badge 5 88123-05-624
17 Blade Screw Kit 1 89440-14-000
18 Blade Iron 5 98079-05-624
28 Blade Set 1 G0113-27-000
27 Blade Iron Screw Set 1 G0111-01-000
11 Wall Control Assembly 1 89350-02-000
12 W74 Dual Control 1
13 Décor Wall Plate (White) 1
14 Wire Nut 4
15 Screw 6-32 X .75 2
16 Screw 6-32 2
2 Screwdriver, Phillips 1 65567-01-000
39 Allen Wrench 1 64801-01-232
1 Balancing Kit 1 65520-01-000
3 Light Bulb E12 C7 (15W) 6 76323-01-000
31 Candelabra Bulb (40W) 3 77646-07-000
17
PARTS LIST

4
Motor Identication Plate
RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION!
Please take a moment to locate the model number and serial number from your fan (see below) and record
this information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear
there already.These numbers are found on the motor identication plate afxed to the fan motor in the
location shown below:
PLEASE INSPECT ALL PACKAGING PRIORTO DISCARDING!
Your Casablanca fan was crafted with pride and care and inspected thoroughly prior to
shipment. Before you begin to assemble and install your Casablanca fan, remove all
parts from the carton and check them against the Parts Guide in this manual.
Make sure all parts are included in the box using the Parts Guide on the following pages.
If there are missing or broken parts:
Call 1-888-227-2178 Monday through Friday,
7a.m. to 4 p.m. PST.Your request will be handled
immediately. Replacement parts will be sent to you
via Federal Express.
Proper Parts Handling
Do not remove lightbulbs from their packaging
until you are ready to install them.
Before discarding packaging materials, be certain
that all parts have been removed.
Use a clean, dry paintbrush to remove small
Styrofoam pieces that may remain after unpacking.
Do not brush Styrofoam into wiring cavities.
The blades in each pack are matched for equal
weight to assure smooth fan operation. If more
than one fan is being installed, do not mix blades
from different cartons.
When cleaning, painting, or working near your fan,
be cautious of the fan and blades.
Always turn power to the ceiling fan OFF before
replacing lightbulbs or working on your fan.
Never insert anything into the path of the fan
blades while the fan is in operation.
Never install a fan over a pool or spa.
Never operate a fan that has been damaged in any
way.
Install the fan according to the instructions in this
manual.
If the fan does not work:
Refer to theTroubleshootingTips in this Owner’s
Manual.
CallTechnical Support at 1-888-227-2178.
Contact your local Authorized Service Center.
Our Web site at www.casablancafanco.com
contains additional information on Casablanca
products, troubleshooting, and Authorized Dealer
or Service Centers. Please do not return this
product to the store.
Serial Number
Veneto
TYPE HANGER TYPE
DJ01 1151 MODEL C15G624L
Memphis, TN
SERIAL No.: DJ06 2237
C15G624L Model Number

5
Veneto ™
Circuit Breaker
(Trip breaker for the
circuit you will be
working on)
Fuse Box
(Remove fuse for the
circuit you will be
working on)
18"
70"
SAFE USE
• CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical
Code, ANSI/NFPA 70-1999 and local codes. If you are unfamiliar with the wiring codes, you should use
a qualied electrician. To avoid overheating and possible damage to other equipment, do not install
control to a receptacle, uorescent light xture, motor-operated appliance, or transformer-supplied
appliance.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed
for ceiling fan installations. If it is not, a new box must be installed. Casablanca extension poles are
available for sloped or high ceiling installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit.
The maximum current requirement for the fan with light xture is 2.9 amps.The fan uses about 1 amp
or 100 watts. Maximum light current is 1.8 amps or 210 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the
canopy, make sure all wires are within the canopy and that no wires are being pinched.
WARNING: Do not bend the blade brackets when installing the brackets, balancing the blades, or
cleaning the fan. Do not insert foreign objects in between the rotating fan blades.
Unpacking
Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check
them against the parts listed in the Parts Guide. Before discarding packaging materials, be certain that all
parts have been removed.
For best performance and for your warranty to be valid, use only genuine Casablanca blades, light
xtures, and accessories.
INTRODUCTION
• The blades in each pack are matched for equal
weight to assure smooth fan operation. If more
than one fan is being installed, be careful not to
mix blades from different cartons.
• Inspect the contents of your carton for possible
shipping or handling damage. If parts are missing
or damaged, call 1-888-227-2178.
• It is always a good idea to have an assistant to
help with the installation.
• When cleaning, painting, or working near your
fan, be very careful of the fan and blades. Always
turn the power OFF to the ceiling fan before
working on it or replacing lightbulbs.
• Never insert anything into the path of the fan
blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company by
calling
1-888-227-2178, or contact your local authorized
Casablanca dealer for assistance in obtaining
service.
BEFORE YOU START
84"

6
MOUNTING RECOMMENDATIONS
SLOPED CEILING INSTALLATION
Before mounting your Casablanca fan, read the following helpful recommendations.The location of the
fan, air circulation, and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your
home. We suggest you follow these mounting recommenda-
tions as you decide where to install your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7'
above the oor.
• Do not locate the fan in a doorway or above a swinging door.
• In bedrooms, fans work best when mounted above the foot of
the bed.
• Over pool tables, be sure to provide plenty of clearance to avoid
damage from pool cues.
• In kitchens be sure to allow for open cupboard doors to clear
the fan blades.
• Do not install a fan close to or over a pool or spa. High humidity combined with corrosive gases will
destroy the nish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52" fan even in smaller rooms. For very large
rooms, two fans may be needed.
Calculation of Ceiling Angle
Use the tear-off Ceiling AngleTemplate card inserted
in this manual. It provides you with a simple “go”
or “no-go” for installing your fan on a sloped
ceiling.
7' minimum
When to Use Extension Poles
For optimum performance and appearance,
an extension pole should be used with your
Casablanca fan when installing on high (cathedral)
ceilings or sloped ceilings. Casablanca offers
standard poles in increments of 6" up to 5'. Custom
poles are available in lengths up to 9'9". See your
Authorized Casablanca Dealer for details.
Blades must be a
minimum of 7 feet
above the oor
Extension
Pole
Maximum ®
angle 32º
This slope is less than 32º.
It is OK to install your fan.
This slope is 32º. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your
fan.
This slope is more than 32º. Your fan will
not hang straight down, an adaptor is
necessary. Contact your local Authorized
Casablanca Dealer in regards to purchasing
a “Sloped Ceiling Adaptor.”
Note: Fan may wobble or vibrate if pole length is
not long enough and inside blade is too close to
downslope or side wall. Extending pole length will
usually solve problem.
SUGGESTED EXTENSION POLE LENGTHS
Ceiling Height Pole Length
9' 0" Standard
9' 6" 18"
10' 0" 18"
11' 0" 24"
12' 0" 36"
13' 0" 48"
14' 0" 60"
EXAMPLE 3
EXAMPLE 2
EXAMPLE 1

7
Veneto ™
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either
the circuit breaker or fuse box), lower the old
xture and disconnect the wiring. Check the
ceiling xture outlet box to be sure it is marked
“Approved for Ceiling Fan Mounting.” If it is not,
a new box must be installed.
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing xture located
where you wish to place your Casablanca fan,
an approved ceiling xture outlet box must be
installed and wired.
Note:The weight of this fan is 47 pounds.
WARNING!
To reduce the risk of re, electrical shock, or
personal injury, mount to outlet box marked
“Acceptable Fan Support of 22.7 kg (50
lbs.) or less” using the mounting hardware
provided with the outlet box or directly to
structure.
CEILING HARDWARE (not to scale)
WARNING!
Support directly to building structure
only.
MOUNTING BRACKET INSTALLATION
Note: After removing the old xture, check the
outlet box to insure that it is supported by a
joist or beam across its upper surface. If not, a 2
x4 stud must be installed.
Mounting Bracket
#8 Wood Screw and Washer (2)
#10 Wood Screw (2)
FAN INSTALLATION
Step 1. Drill two pilot holes into the wood support
structure through the outermost holes in the outlet
box.The pilot holes should be 9/64” in diameter.
Step 2. Thread the lead wires from the outlet box
down through the hole in the middle of the ceiling
plate.

8
PIPE SCROLL ASSEMBLY
PIPE SCROLL HARDWARE
MOUNTING BRACKET INSTALLATION CONT.
Step 3. Align the slotted holes in the ceiling plate
with the pilot holes you drilled in the wood support
structure. For proper alignment use slotted holes
directly across from each other.
Note: The isolators should be ush against the
ceiling.
Step 4. Place a at washer on each of the two
3” wood screws and pass the screws through the
slotted holes in the ceiling plate into the pilot holes
you drilled.
Step 5. Tighten the screws into the 9/64” pilot
holes; do not use lubricants on the screws. Do not
over tighten.
Joist
Ceiling Fan
Approved
Wiring Box
Washer
Wood
Screw
Allen
Wrench
ALLEN SET
SCREW
(pre-installed) Scroll Bracket Decorative Scroll
Screws (3) Decorative Scroll
Arm (3)
Scroll
Screws (3)
Note: On sloped ceilings, align
the canopy opening toward
the top or peak of the room.
Screwdriver Canopy Trim Ring
Step 1. Remove the Paper Shield from the top of
the motor.
Step 2. Using the Allen Wrench, loosen the Set
screw at the top of the Scroll Assembly, and on the
Motor Adapter on the top of the Motor.
Step 3. Remove theTrim Ring from the Canopy.
Step 4. Insert the Pipe Assembly through the
Canopy rst,Trim Ring second, and nally the
Scroll Bracket.
Step 5. Feed the wires from the fan through the
downrod.
Note: Make sure all the wires are on the same side
of the metal dowel pin inside the dowrod.
Canopy
Trim Ring
Scroll Bracket
Fan Wires
Pipe Assembly

9
Veneto ™
Step 6. Twist the Pipe Assembly into the Motor
Adapter by turning Counter-Clockwise.
Step 7. Securely retighten the setscrew on the
Motor Adapter with the Allen Wrench.
CAUTION: The Motor Adapter has a special
coating on the threads. Do not remove this
coating; the coating prevents the downrod
from unscrewing. Once assembled, do not
remove the downrod.
Canopy
Decorative
Arm
Decorative
Scroll Screw Scroll Bracket
Step 8. Insert one of the Scroll Screws through
the hole on one of the Decorative Scroll Arms and
screw into one of the holes on the Scroll Bracket.
Do not tighten.
Note: Ensure the Canopy is above the Scroll
Bracket before securing the Decorative Arms.
Step 9. Repeat until all 3 scroll arms are attached
to the Scroll Bracket.
Step 10. Place the Scroll Assembly on top of the
motor.
Step 11. Line up the Holes on the bottom of the 3
scroll pieces with the tabs on the top of the motor
and attach with the 3 scroll Assembly Screws. Do
not tighten.
Step 12. Adjust the Scroll Assembly until it is lined
up straight on the Pipe Ball and Fan Motor, then
Tighten all Screws, including the set screw on the
Scroll Bracket.
CAUTION: Failure to fully lock in the downrod
before securely tightening the allen set screw may
cause the fan to separate from the downrod during
normal operation!

10
UPPER GLASS HARDWARE
Upper Glass Upper Bulb (6)
UPPER GLASS ASSEMBLY
Step 1. Slide the Glass over the upper part of the
Fan Assembly.
Step 2. The Glass should rest inside the rim of the
lower part of the motor on top of the foam strips to
avoid contact with rim.
Step 3. Remove each of the 6 Upper Bulbs from
their packs and Screw into the Bulb Sockets around
the top part of the fan.
Note: When replacing bulbs, only replace with max
15 watt bulbs.
Rim
HANGING THE FAN
Step 1. Trim wires to about 6" from the top of the
downrod.
Step 2. Strip 1/2" of insulation off each wire using
wire strippers. Raise the fan and place the ball into
the hanger bracket.
Step 3. Align the notch on the ball with the indent
in the hanger bracket. (Rotate the fan until you hear
the notch pop into place.)
Indention
Notch
WARNING: Fan may fall if
not assembled as directed
in these installation
instructions.

11
Veneto ™
Power From
Ceiling
Line Power
(IN)
Line Neutral
(IN)
White
Neutral From
Ceiling
Step 1. Locate the White Line Neutral (IN) and
connect it to the White Neutral Wire from your
ceiling using one of the supplied orange wire caps.
Step 2. Connect the Black Line Power (IN) and the
Black Power Wire from your ceiling with an orange
wire cap.
Step 3. Tuck the White and Black connected wires
back into the ceiling box through the hole in the
center of the Hanger Bracket while you slide the
Receiver into the open end of the Hanger Bracket as
shown.
NOTE: Ensure you do not tuck the bare ground
wire from the ceiling back into the box.This will be
connected later.
Bare Ground
Wire
Tuck Wires
in Box
WIRING HARDWARE
Receiver Blue Wire Caps (4) Orange Wire Caps (3)
WIRING
Blue -Downlight
Power
Black/White
Stripe-Uplight
Power
Step 4. Connect the Blue Downlight Power Wire
from the Receiver to the Blue Wire coming from the
fan with a blue wire cap.
Step 5. Connect the Black/White striped Uplight
Power Wire to the Black/White Wire coming from
the fan with a blue wire cap.

12
White-Neutral
to Fan
Red-Power
to Fan
Bare from
Ceiling
Green from
Mounting Plate
Green from
Fan
Step 6. Take the White Neutral to Fan Wire and
connect it to the White Wire coming from the fan
with a blue wire cap.
Step 7. Use the Red Power to Fan Wire and
connect it to the Red Wire coming from the fan with
a blue wire cap.
Step 8. Connect the Green wire from the
Mounting Plate, Bare Wire from the ceiling, and
the Green Wire from the downrod assembly and
connect them together with an orange wire cap.

13
Veneto ™
Step 9. Carefully tuck the wires around the
Receiver and Hanging Bracket as not to loosen the
wire caps.
Step 10. Insert 2 Canopy Screws into the Hanging
Plate diagonally across from each other so they
match the keyholes on the canopy.
Canopy Screws
Keyhole Slots
Step 11. Raise the Canopy over the Hanger Bracket.
Align the partially installed screws with the key slots
in the canopy.
Step 12. Twist the Canopy clockwise to secure.
Step 13. Install the third & fourth canopy screws in
the round holes on Canopy. Securely tighten all four
screws.
Step 14. Using both hands, push the CanopyTrim
ring up to the top of the Canopy.
Step 15. Twist the CanopyTrim ring clockwise to
secure it to the Canopy.
Keyhole Slot
Round
Hole
WARNING: Do not let wires
become lodged between
Hanger Bracket and Canopy.
CANOPY HARDWARE
SECURING THE CANOPY
Screw DriverCanopy Screw (4)

14
BLADE HARDWARE
BLADE INSTALLATION
Blades (5) Blade Irons (5) Medallions (5)
Blade Screws
(21)
Blade Iron
Screws (11)
Step 1. Insert the Medallion into the holes in the
Blade.
Step 2. Align the screw holes on the Blade Iron
with the holes in the Medallion.
Step 3. Insert 4 Blade Screws and tighten by
hand.
Step 4. Repeat steps for each Blade.
Step 5. Remove the Polyfoam ring from between
the bottom motor housing and Light Kit Mounting
Plate before installing the Blade Irons.
Step 6. Align the Blade Iron to 2 of the holes on
the Blade Iron Adapter on the bottom of the Fan.
Step 7. For each blade, insert one blade mounting
screw through the blade iron, and attach lightly to
the fan. Insert the second blade mounting screw,
then securely tighten both mounting screws.
Medallion
Blade
Blade Iron
Blade Iron
Adapter

15
Veneto ™
LIGHT KIT HARDWARE
LIGHT KIT INSTALLATION
Lower Glass Light Kit
Light Kit Screw (3)
Lower Bulb (3)
Glass Cover Finial
Step 1. To attach the Light KIt Mounting Plate
partially install two light kit screws into the switch
housing mounting plate.
Step 2. Connect the molex plug on the Light Kit to
the Fan.
Step 3. Align the keyhole slots in the Light Kit with
the light kit screws.
Step 4. Turn the Light Kit counterclockwise until the
light kit screws are rmly situated in the narrow end
of the keyhole slots.
Light Kit Screws
Step 5. Install the remaining screw into the Light
Kit.
Step 6. Tighten all three screws rmly.
Molex Plug
WARNING: Do not let wires
become lodged between Fan
Adapter and Light Kit.

16
Step 7. Remove the three lower bulbs from their
packaging, and install into the light kit.
Note: When replaceing bulbs, only replace with max
40 watt bulbs.
Step 8. Raise the Glass up to the Glass Adapter on
the bottom of the Light Kit.
Step 9. Slide the Glass Cover onto the bottom of the
glass
Step 10. Screw the Finial onto the bottom of the
Light Kit Stem to secure Light Kit.
Stem
Cover
Finial
Glass Adapter
W74 WALL CONTROL PREPARATION
Wall Plate
Screws (2)
Switch
Mounting
Screws (2) (4) Wire Cap
WARNING!
To avoid possible electrical shock, make
certain that electricity is turned off at the
circuit breaker or fuse box before attempting
any installation or repair procedure
CAUTION! NOT turning the power OFF at the
circuit breaker or fuse box may cause damage
to the electronics within the wall control and or
the PC board on the fan.
W74 WALL CONTROL PREPARATION
Circuit Breaker
(Trip breaker for the
circuit you will be
working on)
Fuse Box
(Remove fuse for the
circuit you will be
working on)
W-74
Wall Control Cover Plate

17
Direct - Touch 1 2
0
4 3
INSTALLING THE W74 WALL CONTROL
W-74 CONTROL INSTALLATION
The wall control installs in the same manner as an ordinary light switch, using an existing wall box and
wiring.This controller is designed to signal the fan microcomputer as well as perform normal switching
operations. For this reason the following precautions must be observed:
SINGLE W74 INSTALLATION
NOTE: W-74 Wall Control should only be installed on Casablanca's Direct-TouchTM Fans.
1. Use only the Casablanca W-74 wall control.
2. Do not use any additional control with your
Direct-TouchTM fan (for example, dimmer, or fan
speed control).
3. Do not use more than one fan per wall control.
4. No other light xtures or electrical appliances
may be connected on the circuit controlled by the
W-74 wall control.
W-74
Red
White
Blue
Black/White
CAUTION!
Ensure power is turned OFF at the breaker or fuse panel before starting installation.
NOTE:The RED wire is not used in this
application. DO NOT remove the crimped
cap from the wire.
BLACK AND WHITE
STRIPED WIRE
W-74
Wall Control
2 BLACK
WIRES
RED WIRE
NOT USED
8. Connect the green ground wire coming
from the back of the W-74 control to the
ground wire in the switch box. Secure
the splice with a wire nut.
9. Check your work by using the wiring
diagrams as shown in Figures # 1 and #2.
10. Install the W-74 in the wall box with the
two long screws provided.
11. Install the wall plate with the two white
screws.
1. If you have multiple Direct-TouchTM fans, refer to the
section "changing frequency setting" on page 20.
2. Remove the screws and switch plate from the existing
switch box.
3. Remove the screws holding the switch in the switch
box.
4. Pull the existing switch from the switch box to expose
the wire connections.
5. Remove the two wires from the switch.
6. Connect the BLACK wire from the POWER SOURCE
that you just removed from the switch to the BLACK/
WHITE STRIP wire on the W-74 wall control. Secure
this connection with a wire nut.
7. Connect the second BLACK wire that you just removed
from the switch to the second BLACK wire on the
located on the back of the W-74 wall control. Secure
this connection with a wire nut.
Figure 1
Figure 2

18
1 2
0
4 3
1. To control the fan and lights from two
locations (a three-way circuit), use two W-74
wall controls.
2. Remove the screws and switch plate from the
existing switch box and the screws holding
the switch in the switch box. Figure #5
3. Pull the existing switch from the switch box to
expose the wire connections.
4. Determine which wire is connected to the
common terminal from the power source
(120V AC) of the three-way switch. (The
terminal will be marked on switch).
5. Remove the wire from the common terminal
of the three-way switch. Connect this wire to
the remaining black/white striped wire on the
W-74 control. Secure this splice with a wire
nut. Figure 4
CAUTION!
Ensure power is turned OFF at the breaker or fuse panel before starting installation.
DUAL W74 INSTALLATION
BLACK
BLACK
RED
GREEN
120V AC
BLACK
BLACK WITH
WHITE STRIPE
W-74
RED RED
RED
BLACK WITH
WHITE STRIPE
GREEN
W-74
BLACK
BLACK
BLACK
BLACK
BLACK
NEUTRAL
WHITE
GREEN
To control the fan and lights from two locations (a three-way
circuit), use two W-74 wall controls as shown in the wiring diagram
in Figure #4. Before installing the two switches into the wall, place
both switches side by side, then locate the 6 dip switches on the
side of the two switches as shown in Figure #3.Then make sure that
the dip switches are set to the same address on both switches as
shown in Figure #3. When setting these dip switches you are setting
the channel number that is required to control both your fan and
lights from both sides of the room. If you are installing other Direct-
TouchTM 3 fans within your home you may need to reset the dip
switches on these other fans to a different channel before installing
your W-74 wall control into the wall. Please review the section on
channel changing within this part of the operation manual as shown
on page #20.
DIP SWITCHES
W-74
Wall Control
BLACK AND WHITE
STRIPED WIRE
2 RED WIRES
2 BLACK
WIRES
6. Remove the two remaining wires from the three-way
switch. Connect the black wire of these wires to a black
wire on the W-74 control. Secure the splice with a wire nut.
The remaining red wire is to be connected to the other red
wire on the
W-74. Secure the splice with a wire nut. Figure 5
7. Connect the green ground wire coming from the back of the
W-74 control to the ground wire in the switch box. Secure
the splice with a wire nut.
8. Check your work by using the wiring diagrams as shown in
Figures # 4 and #5 on this page.
9. Install the W-74 in the wall box with the two long screws
provided.
10. Install the wall plate with the two short color-matched
screws provided.
11. Installation of the second W-74 control is identical. Repeat
steps 1 through 7.
Figure 3
Figure 4
Figure 5

19
Direct - Touch 1 2
0
4 3
OPERATION POWER
The
1 2
0
4 3
power button is normally left in the on position. Always turn the
power off during cleaning or servicing the fan and during thunderstorms. It
is also used to exit or enter additional programs.
The
1 2
0
4 3
power button must be left on to retain a previously set fan speed
or light level.
OPERATION SPEED CONTROL
There are ve individual speed settings for the fan. Each speed is
indicated by the number on the controller and an audible tone for
each speed.
To select the desired fan speed:
Press the number on the controller corresponding to the speed
desired. 4 is high, 3 medium, 2 low, 1 ultra-low, and 0 is off.
OPERATION REVERSING AIRFLOW
The direction of airow can be changed from downward to upward
or from upward to downward.
To reverse the airow:
1. Make sure the fan is on and blades are turning.
2. Press the
1 2
0
4 3
reverse button.You will hear a series of clicks
from the fan as it speeds up before coming to a stop and
changing direction.
To turn the lights off and on, press and release the
1 2
0
4 3
button for
either the up or down lights for less than one second.
To dim either the up or down light, Press and hold the
1 2
0
4 3
button
for either the up or down light for more than 1 second.The light will
come on at the last brightness setting and increase in brightness
until full power is reached, then start dimming until the lowest
setting is reached.This cycle will repeat until you release the light
button.
OPERATION LIGHTS
1 2
0
4 3
1 2
0
4 3
1 2
0
4 3
Note: It is normal for the fan
to start in the "High" position
from "Off" before changing to
the selected speed.
1 2
0
4 3
Up Light
Down Light
Note:The dimming feature
will only work as long as the
dimming feature remains
active. See "Operation CFL
mode".
W-74 OPERATION

20
1 2
0
4 3
CHANGING FREQUENCY SETTING
NOTE: All fans leave the factory set to
“111111”
You will only have to change the dip switch settings in the remote if you
are using more than one fan in the same area and want to control them
separately.
DIP SWITCHES
SET TO ‘111111’
(Factory Setting)
NOTE: DO NOT set dip switch setting in the
remote to ‘0000’, this may cause frequency
interference from other Casablanca Products.
1. Turn power OFF at the circuit breaker or fuse box and at the toggle
switch, for the fan you want to change.
2. Remove the screws and switch plate from the existing switch box.
3. Remove the screws holding the switch in the switch box.
4. Pull the existing W-74 switch from the switch box to expose the dip
switches located on the side of the control as shown in Figure #1.
5. Change the dip switch settings, assuring that they are different from
the previously installed Direct-Touch fan.
6. Mount the W-74 Wall Control unit back into the wall electrical box.
7. At the circuit breaker or fuse box and at the toggle switch, turn the
power off for the fan whose frequency you are changing.
8. Within 20 seconds of restoring power to the ceiling fan and the W-74
Wall Control press and hold both the “1” and
1 2
0
4 3
reverse buttons
as shown in Figure #2. For 3 seconds, you will hear one tone from
the Piezo Buzzer indicating the command has been accepted.The Fan
and Lights will be off.
DIP
SWITCHES
(Figure 1)
OPERATION CFL MODE
Your fan has the ability to disable the dimming feature to allow the use of
CFL bulbs.
To activate CFL mode:
1. Turn the fan off by pressing the
1 2
0
4 3
power button.
2. Allow the fan to remain off for at least 5 seconds.
3. Press the power button again to restore power to the fan.
4. Immediately press and hold the "1" and "3" buttons for at least 5 seconds.The fans lights will go to
100% brightness and the dimming function will be disabled.
To cancel CFL mode:
5. Turn the fan off by pressing the
1 2
0
4 3
power button.
6. Allow the fan to remain off for at least 5 seconds.
7. Press the power button again to restore power to the fan.
8. Immediately press and hold the "2" and "4" buttons for at least 5 seconds.The fans lights will dim to
50% brightness and the dimming function will be enabled. Press and hold the light buttons until the
desired dimmer setting is reached.
Caution: CFL bulbs will not
function properly when
dimmed, which may result
in ickering or reduced bulb
life.
(Figure 2)
1 2
0
4 3
DIP SWITCHES
SET TO ‘000000’