Cateye CC-PA110W User manual

1
CATEYE
PADRONE
+
CYCLOCOMPUTER
CC-PA110W
Setting up the
computer
Mounting the
computer
Starting
measurement
Changing settings
Warning / Caution
Product Warranty, etc.
• This instruction manual is subject to change
without notice. See our website for the latest
instruction manual (PDF).
• Please visit our website, where a detailed
Quick Start manual containing videos can be
downloaded.
http://www.cateye.com/products/detail/CC-PA110W/manual/
Appendix
3
SET 4
2
1

2
11
(1/3)
(2/3)
Mounting the computer
1 Mount the bracket
• When mounting on stem
• When mounting on handlebar
When mounting the bracket on a handle-
bar, adjust the angle of the bracket so that
the back of the computer faces the speed
sensor when the computer is attached.
Bracket band
Bracket Dial
Bracket rubber pad Speed sensor
Sensor rubber pad
Magnet
Nylon tie
(x2)
StemBracket band
Bracket
Bracket rubber pad
HandlebarBracket band
Bracket
Bracket rubber pad
Cutting band after mounting
CAUTION:
Cut the bracket band so
that cut end will not cause
injury.
Dial
Cut
Correct Wrong
Appendix
3
SET 4
2

3
11
(1/3)
(3/3)
(2/3)
Max.
70 cm
Mounting the computer
2 Mount the speed sensor
3 Mount the magnet
Mount the speed sensor in a posi-
tion where the distance from the
computer to the speed sensor is
within the signal range.
• Mounting on left front fork
• Mounting on right front fork
SENSOR ZONE
SENSOR ZONE
Cut
Pull tight
Nylon tie
Speed sensor
Sensor rubber pad
To sensor zoneSpoke
Magnet
Appendix
3
SET 4
2

4
11
(3/3)
(2/3)
SENSOR ZONE
SENSOR ZONE
5 mm
Mounting the computer
5 Attach/detach computer
6 Test operation
After attaching the computer, rotate the front wheel gently to check that current
speed is displayed on the computer.
If the speed is not displayed, refer to the attachment conditions in steps 1, 2, and 4
again.
4 Adjust the speed sensor and the magnet
* The magnet may be mounted at any position on spoke as long as attachment
conditions are satisfied.
The magnet passes through
the speed sensor zone.
The clearance between the
speed sensor and the magnet
is within 5 mm (3/16”).
Magnet
Sensor zone
Speed sensor
Speed sensorMagnet
ClickClick Hold computer.
Push out so that front lifts up.
Appendix
3
SET 4
2

5
22
(1/2)
(2/2)
When using the
computer for the
first time, configure
the initial settings.
AC
MODE
MENU
AC
Battery case
cover
Dot section
Short press
Long press
(2 sec.)
1 Clear all data.
Press the AC button on the back of the computer.
* All data is deleted and the computer is reset
to its factory default settings.
2 Select the measurement unit.
Select “km/h” or “mph”.
3 Set tire circumference.
Enter the tire circumference of the front wheel
in mm.
* Refer to “Tire circumference”(page 6).
4 Set the clock.
Each time MODE is pressed and held, settings
switch from time display mode, to hours, to
minutes.
* When 12h mode is selected, make sure to
check whether A(a.m.) or P(p.m.) is dis-
played before entering the value.
5 Press MENU to complete setup.
Setup is completed and the computer switches to the mea-
surement screen. For instructions on how to start mea-
surement, refer to “Starting measurement”(page 7).
MODE
MODE
MENU
MENU
MENU
MODE
MODE
MODE
Setting up the computer
km/h ↔mph
Confirm
Increase
numbers
Move to next digit
(Press and hold)
Confirm
Setup complete
MODE
MODE
Switch between
24h and 12h or
increase numbers
Switch setting item
(Press and hold)
Time display mode
MinutesHours
Appendix
3
SET 4
1

6
22
(1/2)
(2/2)
Tire circumference
Tire circumference can be determined by either of the following two methods:
• Measure the actual tire circumference (L)
After ensuring that the tire pressure is appropriate, sit on your
bike, roll it forward so that the tire makes one full revolution (use
the valve or other marking as a reference), and measure the dis-
tance traveled on the road.
• Tire size chart
* The tire size or ETRTO code is indicated on the side of the tire.
ETRTO Tire size L (mm)
47-203 12x1.75 935
54-203 12x1.95 940
40-254 14x1.50 1020
47-254 14x1.75 1055
40-305 16x1.50 1185
47-305 16x1.75 1195
54-305 16x2.00 1245
28-349 16x1-1/8 1290
37-349 16x1-3/8 1300
32-369 17x1-1/4 (369) 1340
40-355 18x1.50 1340
47-355 18x1.75 1350
32-406 20x1.25 1450
35-406 20x1.35 1460
40-406 20x1.50 1490
47-406 20x1.75 1515
50-406 20x1.95 1565
28-451 20x1-1/8 1545
37-451 20x1-3/8 1615
37-501 22x1-3/8 1770
40-501 22x1-1/2 1785
47-507 24x1.75 1890
50-507 24x2.00 1925
54-507 24x2.125 1965
25-520 24x1(520) 1753
24x3/4 Tubular 1785
28-540 24x1-1/8 1795
32-540 24x1-1/4 1905
25-559 26x1(559) 1913
32-559 26x1.25 1950
37-559 26x1.40 2005
40-559 26x1.50 2010
47-559 26x1.75 2023
50-559 26x1.95 2050
54-559 26x2.10 2068
57-559 26x2.125 2070
58-559 26x2.35 2083
ETRTO Tire size L (mm)
75-559 26x3.00 2170
28-590 26x1-1/8 1970
37-590 26x1-3/8 2068
37-584 26x1-1/2 2100
650C Tubular 26x7/8 1920
20-571 650x20C 1938
23-571 650x23C 1944
25-571 650x25C 26x1(571) 1952
40-590 650x38A 2125
40-584 650x38B 2105
25-630 27x1(630) 2145
28-630 27x1-1/8 2155
32-630 27x1-1/4 2161
37-630 27x1-3/8 2169
40-584 27.5x1.50 2079
50-584 27.5x1.95 2090
54-584 27.5x2.1 2148
57-584 27.5x2.25 2182
18-622 700x18C 2070
19-622 700x19C 2080
20-622 700x20C 2086
23-622 700x23C 2096
25-622 700x25C 2105
28-622 700x28C 2136
30-622 700x30C 2146
32-622 700x32C 2155
700C Tubular 2130
35-622 700x35C 2168
38-622 700x38C 2180
40-622 700x40C 2200
42-622 700x42C 2224
44-622 700x44C 2235
45-622 700x45C 2242
47-622 700x47C 2268
54-622 29x2.1 2288
56-622 29x2.2 2298
60-622 29x2.3 2326
Setting up the computer
L mm
Appendix
3
SET 4
1

7
33
(2/3)
(1/3)
MODE
MODE
MODE
MODE
MODE
MODE
* Av displays .E instead of the measurement value when Tm exceeds approximately
100 hours or Dst exceeds 9999.99 km. Reset the computer.
Switching current function
Pressing MODE switches the current function displayed at the bottom of the screen.
Starting measurement [Measurement screen]
On the measurement screen, press MENU to go to the menu
screen. Various settings can be changed on the menu screen.
MODE
MENU
Night Mode icon
Turns on when Night Mode
is ON. For details, refer to
page 10.
Current speed
0.0 (4.0) – 99.9 km/h
[0.0 (3.0) – 62.0 mph]
Measurement unit
Current function
MODE operation when mounted on bracket
When the computer is mounted on the brack-
et, pressing the dot section on the computer
depresses the MODE button.
Moving Time
0:00’00” – 99:59’59”
Trip Distance
0.00 – 9999.99 km [miles]
Average Speed (*)
0.0 – 99.9 km/h
[0.0 – 62.0 mph]
Stopwatch
Turning ON the
stopwatch setting
on the menu screen
adds a stopwatch
to the current func-
tion display. 0:00’00” – 99:59’59”
Maximum Speed
0.0 (4.0) – 99.9 km/h
[0.0 (3.0) – 62.0 mph]
Total distance
0.0 – 99999.9 km [miles]
Clock
0:00 – 23:59 or
1:00 – 12:59
Appendix
SET 4
2
1

8
33
(2/3)
(1/3)
(2/3)
(3/3)
MODE
Starting/stopping measurement
Measurement starts automatically when the
bicycle moves.
During measurement the measurement unit
(km/h or mph) flashes.
Resetting data
Pressing MODE for 2 seconds when on the measurement screen
resets all measurement data to 0 (excluding Odo).
Backlight (Night Mode)
The backlight will come on during the time specified in the Night Mode settings on the
menu screen.
The backlight can be set to come on part time (for 5 seconds) or full time (constantly).
* When the remaining battery power is low (when turns on), the backlight will not
turn on.
Dot
(MODE)
Dot
(MODE)
•
When Full time is selected:
The backlight will come ON while the bicy-
cle is in motion and will turn OFF 30 sec-
onds after the bicycle has stopped.
•
When Part time is selected:
The backlight will come on when MODE is
pressed. Pressing MODE while the back-
light is ON will activate the button’s func-
tion and extend the lighting time.
Starting measurement [Measurement screen]
(2 seconds)
*1: Pressing MODE will turn the backlight
ON, but the button function is disabled.
*2: Pressing the button again while the
backlight is ON will activate the button’s
function.
Backlight off
Backlight on
(*1)
Button function
(*2)
Bicycle begins moving 30 seconds
after stopping
Backlight off Backlight off
Backlight
constantly ON
Measurement stops
Measurement starts
Appendix
SET 4
2
1

9
33
(3/3)
(2/3)
Starting measurement [Measurement screen]
Power-saving function
If the computer does not receive
any signal for 10 minutes, the
power-saving screen is activated
and only the clock is displayed.
If MODE is pressed or a sensor
signal is received while the pow-
er-saving screen is activated, the
computer returns to the measure-
ment screen.
* When the computer is left on
the power-saving screen for 1
hour, the display only shows the
measurement unit. When the
computer is in this state, you
can return to the measurement
screen by pressing MODE.
Using the stopwatch ( )
You can display a stopwatch to count time regardless of whether measurement is started
or stopped.
To use the stopwatch, set the stopwatch setting on the menu screen to ON.
For instructions on how to set the stopwatch, refer to “Stopwatch” (page 13).
Stopwatch operation
Start/stop Press MODE for 1 second when the stopwatch is
displayed.During counting the icon flashes.
Reset Press MODE for 4 seconds when the stopwatch is
displayed.
* Start, stop, and reset operations of the stopwatch are performed
separately to measurement, and do not affect other measure-
ments.
* The stopwatch continues counting regardless of the power-sav-
ing state. During counting the icon flashes on every screen
except for the menu screen.
Stopwatch
MODE
Power-saving
screen
Sleep
1 hour
10 minutes
Appendix
SET 4
2
1

10
SET 44 SET
(2/4)
(1/4)
(Press and hold)
24h display
format “Start time” setting
Increase
numbers
12h display format
P (p.m.)
(Press and hold)
Increase
numbers
A (a.m.)
“End time” setting
24h display
format
12h display format
“Illumination
method” setting
(Press and hold)
Night Mode ON/OFF
P
(Part time)
↔
F
(Full time)
Night Mode
Set the backlight illumination time and method.
Changing settings [Menu screen]
On the measurement screen, press MENU to go to the menu screen.
Various settings can be changed on the menu screen.
* After changing settings, always press MENU to confirm changes.
* When the menu screen is left on for 1 minute, the computer returns to the measurement screen.
Description
Measurement
screen Menu screen
MODE
MODE
MODE
MODE MODE
MODE
MODE
MODE
ON
↔
OFF
MODE
MODE
MENU
MENU
MODE
MODE
MODE
MODE
MENU
MODE
Manual
distance input
Clock
Tire
circumference
Select
measure-
ment unit
Stopwatch
Confirm
(Press and hold)
Change setting
Increase
numbers
12h display format
P (p.m.)
Increase
numbers
A(a.m.)
12h display format
(Press and hold)
Appendix
3
2
1