CB2 STOWAWAY BED User manual

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Made in Vietnam - r12 Page 1 of 8
hardware
tools required
Thank you for purchasing the Stowaway Bed. This
page lists all the contents included in the box. Please
take the time to identify the hardware as well as the
individual components to this product. As you
unpack and prepare for assembly, place the contents
on a carpeted or padded area to protect them from
damage.
Note: 2 people are recommended to safely assemble this product.
Missing hardware? Please call 800.606.6387
for replacements.
12 - spring
washers
4 - small bolts4 - cams
components
1 - center
panel
2 - side panels
(1 left, 1 right)
6 - drawer fronts
2 - short
crossbars
2 - slat
assemblies
12 - flat
washers
8 - brackets
8 - large bolts
16 - small
screws
4 - cam
screws
48 - large
screws
allen wrench (included) phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
2 - partitions
6 - drawer backs
12 - drawer sides
(6 left, 6 right)
6 - drawer bottoms
2 - long
crossbars
stowaway BED

Fit pre-assembled dowels of 2 short crossbars
into corresponding holes of 1 partition as shown.
Secure each short crossbar with 1 flat washer,
1 spring washer and 1 small bolt, using an
allen wrench. Do not over tighten the bolts.
Made in Vietnam - r12 Page 2 of 8
2
1
short crossbar
short crossbar
partition
NOTE: Do not over
tighten the bolts
Fit pre-assembled dowels of 2 short crossbars
into corresponding holes of remaining partition
as shown. Secure each short crossbar with 1
flat washer, 1 spring washer and 1 small bolt,
using a allen wrench.
partition
stowaway BED
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

Made in Vietnam - r12 Page 3 of 8
3
4
With the assistance of another adult, fit slots
of center panel into corresponding slots of
partitions as shown.
center panel
NOTE: Do not over
tighten the screws
Secure center panel to partitions with 4
small screws as shown, using a phillips
head screwdriver. Do not over tighten the
screws.
partition
partition
stowaway BED
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

Made in Vietnam - r12 Page 4 of 8
5
Fit 2 cam screws into 2 long crossbars as
shown. Secure, but do not over tighten, each
cam screw using a phillips head screwdriver.
long
crossbar
6
A
B
NOTE: Make sure
bottom of long crossbar
faces up as shown
Bottom
NOTE: Do not over
tighten the cam screws
A. Fit 4 cams into partitions as shown. Make
sure arrow of each cam points towards nearest
edge with holes.
B. Fit cam screws of each long crossbar into
corresponding holes of partitions as shown.
Using a screwdriver, turn each cam clockwise
until it securely engages each cam screw.
NOTE: Make sure arrow
of each came points toward
nearest edge with holes
long
crossbar
long
crossbar
A
NOTE: Long crossbars should
overhang on top of partitions
stowaway BED
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

Made in Vietnam - r12 Page 5 of 8
7
A. Fit pre-assembled dowels of long
crossbars into corresponding holes of
right side panel. Loosely attach right side
panel to assembly with 4 brackets, 4 flat
washers, 4 spring washers and 4 large
bolts.Repeat for left side panel.
B. At this point, secure left and right side
panels to long crossbars by fully
tightening all bolts using an allen wrench
at a 45º. Do not over tighten the bolts.
C. At this point, secure left and right side
panels to center panel by fully tightening
all bolts.
right side
panel
large bolt
spring washer
flat washer
bracket
left side
panel
A
B
C
long
crossbar
long
crossbar
center panel
stowaway BED
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

Made in Vietnam - r12 Page 6 of 8
8
Secure center panel to left and right side
panels with 2 small screws per side as
shown, using a screwdriver.
center
panel
9
left side
panel
right side
panel
Fit dowels of drawer front into corresponding holes of drawer side. Secure drawer front to
drawer side with 2 large screws as shown, using an allen wrench.
drawer
side
drawer
front
NOTE: Make sure grooves of
drawer side and drawer back
are positioned as shown
stowaway BED
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

Made in Vietnam - r12 Page 7 of 8
12
10 11
Attach dowels of drawer back into correspond-
ing holes of drawer side. Secure drawer side
to drawer back with 2 large screws as shown.
Slide drawer bottom into corresponding
grooves of drawer assembly as shown.
drawer
bottom
Fit remaining drawer side into corresponding
holes of drawer back and front as shown and
secure with 4 large screws. Repeat steps 9-12
for all remaining drawer assemblies.
stowaway BED
drawer
back
drawer
side
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

cleaning & care Clean surfaces witha dry or damp soft cloth.Do not use abrasive cleaners.
NOTE: Each drawer box can support maximum weight of 105 lbs
Made in Vietnam - r12 Page 8 of 8
13
Slide drawer assemblies into assembled
unit as shown.
14
drawer
assembly
With the assistance of another adult, attach
2slat assemblies to assembled unit with 8
small screws as shown, using a screw-
driver.
Assembly is now complete.
stowaway BED
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com