CB2 GLOSS User manual

Made in Vietnam - r04 Page 1 of 4
gloss NIGHTSTAND
hardware
components
tools required
Thank you for purchasing the Gloss Nightstand.This
page lists all the contents included in the box. Please
take the time to identify the hardware as well as the
individual components to this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are recommended to safely install this
product.
Missing hardware?
Please call 800.606.6387 for replacements.
(We recommend the use of hand tools instead of power tools)
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
phillips head screwdriver
8 - screws 4 - cams 4 - bolts
8 - wood
dowels
4 - flat
washers
4 - cam
screws
4 - spring
washers
1 - bottom
panel
1 - top
panel
2 - side panels
(1 left, 1 right)
2 - drawer sides
(1 left, 1 right)
1 - drawer
front
1 - back
panel
1 - drawer
back
1 - drawer
bottom

gloss NIGHTSTAND
Made in Vietnam - r04 Page 2 of 4
12
Insert 4 wood dowels and 2 cams into left and
right side panels as shown. Make sure arrows
on each cam points towards the nearest edge
with holes.
34
Insert 4 cam screws into top panel as shown.
Secure, but do not over tighten, cam screws with
a phillips head screwdriver.
NOTE: Do not
over tighten
the bolts
Position unit upright. Fit back panel into
corresponding grooves of side panels as shown.
Fit dowels on side panels into corresponding holes
of bottom panel as shown. Attach bottom panel
with 4 bolts, 4 spring washers and 4 flat washers,
using a screwdriver. Do not over tighten the bolts.
NOTE: Do not
over tighten
the cam screws
NOTE: Make sure arrows
on each cam points towards
the nearest edge with holes
left and right
side panels
top panel
bottom
panel
left side
panel
right side
panel
NOTE: Make sure grooves
of left and right side panels
are facing each other during
assembly as shown
back panel
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

gloss NIGHTSTAND
Made in Vietnam - r04 Page 3 of 4
56
Fit top panel onto dowels of side panels. Using a
screwdriver, turn cams clockwise until it securely
engages the cam screws.
78
A. Attach left drawer side to drawer front with
2 screws as shown. Secure, but do not over
tighten, screws with a screwdriver.
B. Insert drawer bottom into grooves of drawer
side and front as shown.
Attach right drawer side to drawer front and
back with 4 screws as shown.
Attach drawer back to left side drawer with 2
screws as shown.
A
B
NOTE: Do not
over tighten
the screws
top
panel
left drawer
side
drawer
front
drawer
bottom
drawer
back
right drawer
side
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

gloss NIGHTSTAND
Made in Vietnam - r04 Page 4 of 4
9
Align drawer glides of drawer with corresponding drawer into
corresponding glides of case assembly. Keeping the drawer level,
carefully push the drawer until it is all the way in the case and glides are
securely engaged.
Assembly is now complete.
cleaning & care
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the unit is finished with a protective clear lacquer. It is
recommended to use coasters to protect surface from
heat and water.
NOTE:
Make sure glides are
pulled out of the case, and
ball bearings are at the front of
the extended glides
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com