CBC PT127N-XT User manual

P
PT T1 12 27 7N N- -X XT T
Outdoor Vandal Proof 27x DN PTZ Dome
UUser Manual
NY: 55 Mall Drive • Commack, NY 11725 [phone]
CA: 20521 Earl Street • Torrance, CA 90503 [phone]
www.computarganz.com

G
G
Speed Dome Camera Instruction Manual
2/48
ٻ
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPENٻ
ٻ
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONAL
This lightning flash with arrowhead symbol is i
ntended to alert the user to
the presence of un-
insulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
This exclamation point symbol is intended to alert the
user to the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
G
G
This Device compiles with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interface, and
(2) This device
must accept any interference received, including
interference that may cause undesired operations.

G
G
Speed Dome Camera Instruction Manual
3/48
G
Important Safety Guide
1. Read, heed and follow all the Instructions
Read all the safety and operating instructions before using the product.
2. Keep this manual
Keep this manual for reference in future.
3. Attachments / Accessories
Use only the attachments or accessories specified by the manufacturer.
4. Installation
zDo not install near any heat resources such as radiators, heat registers, stoves, or other
appratus including amplifiers that product heat. Improperly installed product may fall,
cause serious injury to a child or adult and damage the product.
zDo not block any ventilation holes or openings. Install in accordance with the
manufacturer’s instructions.
zUse only with the cart, stand, tripod, bracket, mounting devices, or table specified by
the manufacturer.
zInstallation should be done only by qualified personnel and conform to all the
instructions by the manufacturer.
zRefer all servicing to qualified service personnel.
zUnless the product is specifically marked as IP67, more than IP67 or confirmed by the
manufacturer, it is designed for indoor use only and it must not be installed where
exposed to rain and moisture.
zDo not load on the product.
zUse stainless steel hardware to fasten the mount.
zTo prevent damage from water leakage when installing a mount outdoors on a roof or
wall, apply sealant properly around holes.
zThese servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock, do not perform any servicing other that contained in the
operationg instructions unless you are qualified to do so.
zUse only replacement parts specified by the manufacturer.
5. Power source
This product should be operated only from the type of the power source indicated on the
marking label.
NOTICE

G
G
Speed Dome Camera Instruction Manual
4/48
Caution
Operating
zBefore using, make sure that the power supply and others are properly installed.
zWhile operating, if any abnormal condition or malfunction is observed, stop using the
product immediately and then contact your local dealer.
Handling
zDo not disassemble or tamper with the parts inside the product.
zDo not drop or subject the product to shock and vibration as this can damage the
product.
zCare must be taken when you clean the clear dome cover. Especially, scratch and dust
will ruin the quality of the product.
Installation and Storage
zDo not install the product in areas of extreme temperature, which exceed the allowable
range.
zAvoid installing in humid or dusty places.
zAvoid installing in places where radiation is present.
zAvoid installing in places where there are strong magnetic fields and electric signals.
zAvoid installing in places where the product would be subject to strong vibrations.
NOTICE

G
G
Speed Dome Camera Instruction Manual
5/48
ྙIntroduction
Features
6
Package Components
9
Main Part Description
10
ྚInstallation
DIP Switch Setup
11
Installation with Wall Mount Bracket
14
Wiring and Cabling
15
ྛOperation
Check Point before Operation
19
Check Points for Preset and Pattern Function before Operation
19
OSD Menu
20
Reserved Preset (Hot Keys)
20
Preset
21
Swing
21
Pattern
22
Group
23
Other Functions
23
OSD Display
25
ྜOSD Menu
Quick Programming Guide
26
Main Menu
26
Display Setup
27
Privacy Zone Mask Setup
28
Camera Setup
30
Motion Setup
34
Preset Setup
37
Swing Setup
39
Pattern Setup
40
Group Setup
41
System Initialize
44
ྜྷSpecifications
45
Dimension
48
TABLE OF CONTENTS

G
G
Speed Dome Camera Instruction Manual
6/48
Features

Powerful Zoom Camera & Setup Options
zImage Sensor : 1/4" Super HAD color CCD
zZoom : u27 Optical Zoom, u12 Digital Zoom
z Day & Night, Privacy Mask
z SNR (Super Noise Reduction) Function
z Various Focus Mode : Auto-Focus, Manual Focus, Semi-Auto Focus
zVarious Setup Options in OSD Menu.

Powerful Pan/Tilt Functions
zMAX. 360q/sec High Speed Pan/Tilt Motion
zWith the Vector Drive Technology, Pan/Tilt motions are accomplished along the
shortest path. As a result, the time to target view is remarkably short and the video on
the monitor is very natural in monitoring.
zWith the Micro-Stepping Control Technology, the video looks very natural at high
zoom magnification during a jog operation on a controller since the camera can be
controlled by 0.05q/sec. Hence it is very easy to make the camera focus on desired
target views at high zoom magnification. Additionally it is easy to make the camera
focus on desired positions with zoom-proportional pan/tilt movement.

Preset, Pattern, Swing, Group, Privacy Mask and More…
zMAX. 127 Presets are programmable and each preset can have its own parameter
values independently from the other presets.
For an example, refer to the below table.
Preset No.
White Balance
Auto Exposure
࡯࡯࡯
Label
Remarks
Preset 1
Case A
Case 3
“ENTRANCE”
Preset 2
Case C
Case 5
“WAREHOUSE”
Preset 3
CaseV
Case 2
“OFFICE”
࡯࡯࡯
Preset 95




Reserved for OSD Menu
࡯࡯࡯
Preset 128
Case K
Case 9
“TERRACE”
INTRODUCTION
1

G
G
Speed Dome Camera Instruction Manual
7/48
zMAX. 8 sets of Swing are programmable. This function is that the camera moves
repetitively between two preset positions at programmed speeds.
zMAX. 4 Patterns are programmable. This function is that the camera memorizes the
path (mostly curve path) by the joystick of the controller and revives the trajectory
operated by the joystick as closely as possible.
zMAX. 8 sets of Group are programmable. This function is that the camera memorizes
the combination of Presets, Pattern and/or Swings sequently and runs Presets, Pattern
and/or Swings repetitively. A Group can be combined upto 20 functions with any of
Preset/Pattern/Swing.
zMAX. 8 Privacy Masks are programmable, not to intrude on any other’s privacy.

PTZ(Pan/Tilt/Zoom) Control
zWith the RS-485 communication connection, MAX. 255 units of cameras can be
connected to a single controller.
zPelco-D or Pelco-P protocols can be selected as a control protocol in the current
firmware version.

OSD(On Screen Display) Menu
zOSD menu is provided to display the status of camera and to configure the functions
interactively.
zThe information such as Camera ID, Pan/Tilt Angle, Direction, Alarm Input and Preset
is displayed on screen.

Alarm In/Out Function
z3 alarm sensor inputs and 1 alarm sensor outputs are available.
zAlarm sensor input is decoupled with photo-couplers to avoid external electric noise
and shock perfectly.
zBoth of N.O.(Normal Open) sensors and N.C.(Normal Close) sensors can be used and
the signal range of the Alarm output is from DC 5.0V to 12.0V for various applications.
zThe camera can be set to move to a Preset position or to run functions such as Pattern,
Swing and Group when there are external sensor activations. Also “Post Alarm”
function is possible, which is supposed to activate after user-defined time period and
sequentially in succession to the action by external sensor activations.

Reserved Presets(Hot Keys)
zMost camera setup options can be set up easily and directly with the reserved presets
(Hot Keys), without entering into OSD menu. For more information, refer to “Reserved
Presets(Hot Keys)” in this manual.
INTRODUCTION
1

G
G
Speed Dome Camera Instruction Manual
8/48

Network Function(Only for the IP addressable models)
zNetwork functions including remote monitoring, bidirectional audio and others are
available through IP based network such as LAN, ADSL/VDSL, and Wireless LAN. For
more information, refer to the separated manual for IP Addressable models.

Perfect Outdoor Environment Compatibility and Easy Installation
zThe fans and heaters are built-in in the camera for cold and hot temperature
environment. Also idealistic mechanical design protects the camera from water and
dust. (IP67 when installed properly with wall mount bracket only / Only for outdoor
models)
zIt is easy to install and repair the camera.
INTRODUCTION
1

G
G
Speed Dome Camera Instruction Manual
9/48
Package Component
Product & Accessories
zMain Body & Surface Mount Bracket
zDefault Accessories
[Main Cable,Wrench]
zAccessories for The Models with Alarm In/Out
Function [I/O Cable]
Brackets
zWall Mount Bracket
[Screws :Machine M5u15,Hex Lag #14u50]
INTRODUCTION
1

G
G
Speed Dome Camera Instruction Manual
10/48
Main Part Description
zDome Cover
Do not detach the protection vinyl from the dome cover before
finishing all the installation process to protect the dome cover
from scratches or dust.
zDIP Switch
Used to set up camera IDs and protocols.
zMounting SafetyWire
Used to protect the product from being dropped by connecting
safety wire of bracket to hook of main body when being installed.
zMounting Screw Hole
Used to assemble the main body with a bracket with screws.
zMain Connector
Used for the power wire, the video cable and the RS-485
communication cable connection.
zSensor I/O Port
Used for the sensor in/out connection. (The sensor I/O function
possible models only)
zReset Switch
Used to initialize all the network configurations to the factory
default. (IP addressable models only) Press the button for more
than 5 seconds to initialize the network system.
INTRODUCTION
1

G
G
Speed Dome Camera Instruction Manual
11/48
DIP Switch Setup
Before installing the camera, set up the DIP switch to configure the camera ID and the
communication protocol.
Camera ID Setup
ON
ON
12345678
Pin
1
2
3
4
5
6
7
8
Pin
1
2
3
4
5
6
7
8
ID
1
2
4
8
16
32
64
128
ID
1
2
4
8
16
32
64
128
1
on
off
off
off
off
off
off
off
11
on
on
off
on
off
off
off
off
2
off
on
off
off
off
off
off
off
12
off
off
on
on
off
off
off
off
3
on
on
off
off
off
off
off
off
13
on
off
on
on
off
off
off
off
4
off
off
on
off
off
off
off
off
14
off
on
on
on
off
off
off
off
5
on
off
on
off
off
off
off
off
15
on
on
on
on
off
off
off
Off
6
off
on
on
off
off
off
off
off
16
off
off
off
off
on
off
off
off
7
on
on
on
off
off
off
off
off
17
on
off
off
off
on
off
off
off
8
off
off
off
on
off
off
off
off
18
off
on
off
off
on
off
off
off
9
on
off
off
on
off
off
off
off
19
on
on
off
Off
on
off
off
off
10
off
on
off
on
off
off
off
off
20
off
off
on
off
on
off
off
off
zThe ID number of camera is set using a binary number.
Examples shown below.
z
The range of ID is 1~255. UDo not use 0 as camera ID
U.
Factory default of Camera ID is 1.
z
If you want to control a certain came
ra, you must match the
camera ID with Cam ID setting of DVR or Controller.
INSTALLATION
2

G
G
Speed Dome Camera Instruction Manual
12/48

Communication Protocol Setup
1234
ON
ON
Terminal Resistor Setup
Pin
1
2
3
4
5
6
7
8
Pin
1
2
3
4
5
6
7
8
ID
1
2
4
8
16
32
64
128
ID
1
2
4
8
16
32
64
128
21
on
off
on
off
on
off
off
off
31
on
on
on
on
on
off
off
off
22
off
on
on
off
on
off
off
off
32
off
off
off
off
off
on
off
off
23
on
on
on
off
on
off
off
off
33
on
off
off
off
off
on
off
off
24
off
off
off
on
on
off
off
off
34
off
on
off
off
off
on
off
off
25
on
off
off
on
on
off
off
off
35
on
on
off
off
off
on
off
Off
26
off
on
off
on
on
off
off
off
36
off
off
on
off
Off
on
off
off
27
on
on
off
on
on
off
off
off
37
on
off
on
off
Off
on
off
off
28
off
off
on
on
on
off
off
off
38
off
on
on
off
Off
on
off
off
29
on
off
on
on
on
off
off
off
39
on
on
on
off
Off
on
off
off
30
off
on
on
on
on
off
off
off
40
off
off
off
on
Off
on
off
off
zSelect an appropriate Protocol with the DIP switch combination.
Switch Mode
Protocol
P0
(Pin 1)
P1
(Pin 2)
P2
(Pin 3)
OFF
OFF
OFF
PELCO-D, 2400 bps
ON
OFF
OFF
PELCO-D, 9600 bps
OFF
ON
OFF
PELCO-P, 4800 bps
ON
ON
OFF
PELCO-P, 9600 bps
Others
Reserved
z
Match the camera protocol with the camera protocol in the setting of
your DVR or controller to control the camera.G
zAdjust the DIP sw
itch after turning off the camera. If you changed the
camera protocol by changing the DIP S/W, the change will be effective
after you reboot the camera.
z
The factory default protocol is “Pelco-D, 2400 bps”.
INSTALLATION
2

G
G
Speed Dome Camera Instruction Manual
13/48
The terminal resistor is used for the following cases.
zCase 1 : In case that the control cable length between a camera and
a controller is relatively very long (1:1 Connection)
If the communication
cable length is very long, the electrical signal will
bound in the terminal
point. This reflected signal causes distortion of
original signal. Accordingly, the camera can be out of control. In this
case, the terminal resistor of both sides i.e. the ca
mera and the
controller must be set to ‘ON’ state.
z
Case 2 : In case that multiple
cameras are connected to a
controller.
Due to similar reasons with the case 1, the terminal
resister of the
controller and the last camera must be set to ‘ON’ state. The la
st camera
means the camera farthest in cable length from the controller. Do not
turn on the terminal resistor of all the cameras
on the same
communication cable. G
INSTALLATION
2

G
G
Speed Dome Camera Instruction Manual
14/48
Installation with Wall Mount Bracket
ྙMake a hole whose diameter is 30~40mm
on the mounting surface to pass the
wire(s) and cable(s) through the mounting
surface. (In case of the wiring and cabling
through the mounting surface only) Then
prepare the wall mount bracket. Pull the
wire(s) and c
able(s) for the system as
below. Attach the wall mount bracket to the
mounting surface. (Hex Lag #14u50)
ྚPull the wire(s) and cable(s) for the
system as below. Wire the cable(s) to the
ports.
After assembling hook of camera
main body with safety wire i
nside the
adaptor. A
fter assembly, fix it with 3r
screws.
(Machine M5u15)
ྛAssembles dome cover with safety wire
of main body
and screws main body with
dome cover. A
fter assembly, remove
protection vinyl from dome cover.
Important Notice
zBefore starting the installation,make sure that the Camera ID and Protocol are set up properly.
INSTALLATION
2

G
G
Speed Dome Camera Instruction Manual
15/48
Wiring and Cabling
Port Description
zMain Cable
Port Pin Number (RJ45)
Connector / Wire Color
Signal
1
BNC Connector
Video +
2,4
Video 
5
Red
RS-485 +
3
Yellow
RS-485 
7
Orange
Power +
6,8
White
Power 
zI/O Cable
Port Pin Number (RJ25)
Wire Color
Signal
1
Blue
IN COM +
2
Yellow
IN 1 
3
Green
IN 2 
4
Red
IN 3 
5
Black
OUT A
6
White
OUT B
INSTALLATION
2

G
G
Speed Dome Camera Instruction Manual
16/48
Power Description
zCarefully check the voltage and current capacity of the rated power. The rated power is
indicated in the back of main unit.
Rated Power
InputVoltage Range
Current Consumption
AC24V AC 17V ~ 29V 1.5A
zIn case that the length of the power wire is very long, there may be voltage drop and the
syatem may not work properly. Make the length of the power wire as short as possible.

RS-485 Communication
zFor PTZ control, connect the cable(s) to your keyboard or DVR. To connect multiple
cameras to a single controller, RS-485 communication should be connected in parallel
as shown below. If you are connecting a single camera to a controller, terminate the
camera. When connecting more than one camera to a single controller, terminate the
last camera on the communication line. The last camera means the camera farthest in
cable length from the controller.GNote that the total length of the communication cable
between a controller and the camera(s) on the same communication line must be less
than 1.2Km.G
G
Video
zUse BNC coaxial cable only.
INSTALLATION
2

G
G
Speed Dome Camera Instruction Manual
17/48
Alarm Input
G
zSensor Input
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
Before connecting sensors, check driving voltages and output signal types of the sensors.
Since output signal types of the sensors are divided into Open Collector type and
Voltage Output type in general, the wiring must be done properly after considering
those types.
Signal
Description
IN COM+
The electric power source to drive input circuit. Connect the (+) wire of electric
power source to drive the Sensors to this port as shown in the above circuit.
IN1 -,IN2 -, IN3 -
Connect the outputs of sensors to each port as shown in the above
circuit.
INSTALLATION
2

G
G
Speed Dome Camera Instruction Manual
18/48
If you want to use Alarm Input, the types of sensors must be selected in OSD menu. The
sensor types are divided into Normal Open and Normal Close. If wrong sensor types are
selected, alarms should be activated reversely to sensor inputs.
~Normal Open
Output Voltage is high state when sensor is activated
~Normal Close
Output Voltage is high state when sensor is not activated
Relay Output
The maximum loads are as follows.
Power Type
DC Power
AC Power
Maximum Load
MAX. DC 24V, 1A
MAX. AC 125V, 0.5A
INSTALLATION
2

G
G
Speed Dome Camera Instruction Manual
19/48
Check Points before Operation
zBefore turning on the system, check if the wire(s) and cable(s) are connected properly.
zCheck if the camera ID on the controller is properly selected. The camera ID must be
identical to that of the target camera. The camera ID can be checked by reading the DIP
switch of the camera or on OSD.
zIf your controller supports multi-protocols, the protocol must be changed to match to that of
the camera.
zAdjust the DIP switch after turning off the camera. If you changed the camera protocol by
changing the DIP S/W, the change will be effective after you reboot the camera.
zSince the operation method can be different by controllers, refer to your controller manual
if the camera can not be controlled properly. The operation of this manual is based on the
standard Pelco® Controller.
Check Points for Preset and Pattern Function before Operation
zCheck fully how to operate preset function and pattern function with your controller or DVR
in advance to operate the camera functions when using a controller or a DVR.
zRefer to the following table when using standard Pelco® protocol controllers.
< Go Preset >
Input [Preset Number] and press [Preset] button shortly.
< Set Preset >
Input [Preset Number] and keep pressing [Preset] button for more than 2 seconds.
< Run Pattern >
Input [Pattern Number] and press [Pattern] button shortly.
< Set Pattern >
Input [Pattern Number] and keep pressing [Pattern] button for more than 2 seconds.
zIf your controller or DVR has no pattern button or function, use the Hot Keys with preset
numbers. For more information, refer to “Reserved Presets(Hot Keys)” in this manual.
OPERATION
3

G
G
Speed Dome Camera Instruction Manual
20/48
OSD Menu
zFunction
With OSD menu, the system can be properly configured for each
application.
zEntering into OSD
Go Preset [95]
Reserved Presets (Hot Keys)
zDescription
Some Preset numbers are reserved to change some parameters without entering into
OSD menu.
zHot Keys
Go Preset [95]
:Entering into OSD menu
Go Preset [131~134]
:Running Pattern Function 1 ~ 4
Go Preset [141~148]
:Running Swing Function 1 ~ 8
Go Preset [151~158]
:Running Group Function 1 ~ 8
Go Preset [161]
:Turning off Relay Output
Set Preset [161]
:Turning on Relay Output
Go Preset [167]
:Setting Zoom Proportional Function to ON
Set Preset [167]
:Setting Zoom Proportional Function to OFF
Go Preset [170]
:Setting Camera BLC/WDR Mode to OFF
Go Preset [171]
:Setting Camera BLC/WDR Mode to ON
Go Preset [174]
:Setting Camera Focus Mode to AUTO
Go Preset [175]
:Setting Camera Focus Mode to Manual
Go Preset [176]
:Setting Camera Focus Mode to SEMI-AUTO
Go Preset [177]
:Setting Day & Night Mode to AUTO
Go Preset [178]
:Setting Day & Night Mode to NIGHT
Go Preset [179]
:Setting Day & Night Mode to DAY
Go Preset [190]
:Setting OSD Display Mode to AUTO (Except Privacy Mask)
Go Preset [191]
:Setting OSD Display Mode to OFF (Except Privacy Mask)
Go Preset [192]
:Setting OSD Display Mode to ON (Except Privacy Mask)
Go Preset [193]
:Setting all Privacy Mask Display to OFF
Go Preset [194]
:Setting all Privacy Mask Display to ON
OPERATION
3