ccei Brio WX-100 User manual

1
Brio WX-100_ENG Instruction Manual v2.0
BRIO W
X
PAR-56 Power Led Bul
b
Brio® Color WX-100
Instruction Manual v2.0
Specifications......................................................................................1
Packing contents...............................................................................1
Description...........................................................................................1
Functions..............................................................................................2
PLC Mode..................................................................................... 2
Standalone Mode ....................................................................... 2
Safety....................................................................................................2
Installation............................................................................................3
Transformer................................................................................... 3
Lights protection.......................................................................... 3
Cable Section.............................................................................. 3
Connection Diagram.........................................................................3
WARNING
The power supply of the bulb is 12V AC SELV (Safety Extra Low Voltage) compatible
with the volume 0 (inside the pool) in accordance with standard NF C 15-100.
The light must be immersed before the power is turned on and should never be fed
out of water.
Always cut the power supply before handling the electrical installation.
Specifications
Dimensions PAR-56
Power supply 12 V AC 50Hz/60Hz
Power consumption 100W
Weight 2 kg
Type of LEDs POWER LED RVB P5W
Number of LEDs 18
Max Luminouxs Flux 2000 lm
Color control CPL or ON/OFF
Packing contents
1 bulb BRIO-WX-100
2 stainless steel screws + washers for connection
Instruction Manual (this document)

2
Brio WX-100_ENG Instruction Manual v2.0
Mode Couleurs
1Automatic sequence (with fading)
2Blue
3Green
4Cyan
5Red
6Magenta
7Yellow
8White
Description
LED Bulbs BRIO-WX are designed to replace the incandescent bulbs 300W. They reduce your energy
consumption and illuminate your pool in colors.
The colors are obtained by mixing the 3 primary
colors: Red, Green and Blue (RGB). By adjusting the
intensity of these three colors you can get an infinite
number of nuances. WX bulbs can be controlled
remotely by PLC (Power Line Carrier) through the
Brio CPL (optional) or operate independently.
Functions
PLC Mode
This mode requires a CPL Brio (sold separately) and allows the centralized control of all Brio WX
bulbs connected to the same transformer. For installations with multiple bulbs PLC mode provides
synchronization of changes in color and offers a wide variety of entertainment to your pool
(many sequences, color change in the rhythm of music, remote control etc ...) See the instruction
manual provided with the BRIO-CPL for more information.
Standalone Mode
If no Brio CPL is installed, bulbs operate independently and the user can choose between 8
modes: 7 fixed colors and an automatic sequence of changing colors.
of its last extinction
Safety
The color change can be obtained by switching
off and on the lights for a very short time (<1s). By
successive switches, you can scroll through the 8
modes of operation. After 8 modes, the WX
returns on automatic sequence (mode 1).
To reset the bulbs and bring them together in
mode 1, it should be shut off for about 2s. When
the light is turned on after a period of several
seconds (> 4s), the WX-100 blinks 5 times and
then turns in the way in which it was at the time
In case of an excessive increase of the temperature inside the bulb, the bulb switchs off and
emits red flashes. Once the temperature returns to normal bulb resumes its operation.
Upon detection of a low (11V ac) or too high voltage (15V ac), the bulb stops working and
flashes in green. After default detection, you have to switch off for 5s and to reset once again
the WX.

3
Brio WX-100_ENG Instruction Manual v2.0
Transformer
Power Max N
r
WX-100
100VA 1
300VA 2
600VA 6
SECTION (mm²)
2,5 4610 16
Length max. (m) 6,4 9,6 16 25,6 40
Installation
The WX replaces incandescent bulbs in the 300W 12V
standard PAR56 niches. It is recommended that you hire a
professional for the installation.
Replacing an old light bulb:
Unmount the old and simply connect the BRIO-WX in place.
Use pods as shown below. The connection is done using
stainless steel screws supplied with the bulb.
Make sure you keep the bulb in the right position in order to
crush correctly the O-ring to the rear of the light fixture.
Transformer
The transformer used must have a secondary
voltage of 12V (12.5 V depending on model). Its
power has to match the power of the projectors to be
connected.
12 VAC
In any case, the sum of the projectors must be less or equal to the power transformer.
Lights protection
It is necessary to have an independent protection for each light. Protection should be provided
at the secondary of the transformer by the use of fuses or circuit breakers of 5A or 6A.
For STX installation never use a fuse to protect the lights but a circuit breaker!
Cable Section
The voltage drop in the power cable from the projector must be limited in order not to alter
the colors.
Connection Diagram
L
N
230V
12V
Example :
2 Lights 230V
12V
Protection
10A
BRIO
WX100
Protection
10A
BRIO
WX100
Protection
10A
BRIO
WX100

4
Brio WX-100_ENG Instruction Manual v2.0
Brio® WX-100
Sale Date:........................................................................................................
Serial Nr:...........................................................................................................
Declaration
The company CCEI SA (FR 1507 073 804 973) declares that the
product Brio WX-50 meets the requirements of safety and EMC
European Directives 2006/95/EC and 2004/108/EC.
Emmanuel Baret
Marseille, 01/06/2009
Dealer Stamp
www.ccei.fr