- 2 -
Signal from a Sinking Input (NPN)
You can turn the light ON and OFF with a signal input from the input connector. With these Light Units, you can use a
sinking input (NPN) or a sourcing input (PNP).
Pin 4 Open
Constant Lighting Mode Connection Example
Pin 4 High Voltage
Light Unit status
Pin 2 (NPN)
Lit. Lit.
Low voltage
Open
ON delay time: 55 us max.OFF delay time: 45 us max.
Not lit.
Minimum operating time:
Approx. 100 us
Light Unit status
Pin 2 (NPN)
Lit. Lit.
Low voltage
Open
ON delay time: 55 us max.OFF delay time: 45 us max.
Not lit.
Minimum operating time:
Approx. 100 us
Pin 2 (NPN)
Low voltage
Open
Light Unit status Not lit. Not lit.
OFF delay time: 45 us max.
Lit.
ON delay time: 55 us max.
Minimum operating time:
Approx. 100 us
Pin 2 (NPN)
Low voltage
Open
Light Unit status Not lit. Not lit.
OFF delay time: 45 us max.
Lit.
ON delay time: 55 us max.
Minimum operating time:
Approx. 100 us
LDLB Light UnitExternal Circuit
Pin 4
Pin 3
Pin 2
Transistor (NPN)
open collector
LDLB Light UnitExternal Circuit
5 VDC
24 VDC
Pin 4
Pin 3
Pin 2
Transistor (NPN)
open collector
5 VDC
**
Switch the signal input on pin 2 to turn the light ON and OFF with a signal from a sinking input (NPN). Also, you can input
a high voltage on pin 4 to switch the logic for turning the light ON and OFF. Switch the signal input on pin 4 to turn the light ON and OFF with a signal from a sourcing input (PNP). Also, you can input
a low voltage on pin 2 to switch the logic for turning the light ON and OFF.
* Use an element or switch with a current ow of approximately 1 mA in the external circuit.
Logic Ta ble
Refer to the following table for the low and high voltages.
Logic switching
Pin 4 Open High voltage
Signal input Pin 2 (NPN) Open
Low voltage
Open
Low voltage
Operating
mode
Constant Lighting Mode
Lit. Not lit. Not lit. Lit.
Overdrive Mode
Not lit. Lit. Lit. Not lit.
Logic switching
Pin 2 Open Low voltage
Signal input Pin 4 (PNP) Open
High voltage
Open
High voltage
Operating
mode
Constant Lighting Mode
Lit. Not lit. Not lit. Lit.
Overdrive Mode
Not lit. Lit. Lit. Not lit.
Pin
Signal input status
Range
Pin 2 (NPN) Low voltage 0 to 1.1 VDC
Pin 4 High voltage
20.7 to 26.4 VDC
Pin
Signal input status
Range
Pin 2 Low voltage 0 to 1.1 VDC
Pin 4 (PNP) High voltage
20.7 to 26.4 VDC
Transistor
(NPN)
Pin 2
Pin 3
(ground)
Switch,
relay, etc.
Pin 2
Pin 3
(ground)
Signal from a Sourcing Input (PNP)
Pin 2 Open
Constant Lighting Mode Connection Example
Pin 2 Low Voltage
Overdrive Mode
LDLB Light UnitExternal Circuit
5 VDC
24 VDC
Pin 4
Pin 3
Pin 2
Transistor (PNP)
open collector
*
LDLB Light UnitExternal Circuit
5 VDC
24 VDC
Pin 4
Pin 3
Pin 2
Transistor (PNP)
open collector
*
Pin 4 (PNP)
High voltage
Open
Lit.
Light Unit status Lit.
OFF delay time: 45 us max.
Not lit.
ON delay time: 55 us max.
Minimum operating time:
Approx. 100 us
Pin 4 (PNP)
High voltage
Open
Lit.
Light Unit status Lit.
OFF delay time: 45 us max.
Not lit.
ON delay time: 55 us max.
Minimum operating time:
Approx. 100 us
Light Unit status
Pin 4 (PNP)
Not lit. Not lit.
High voltage
Open
ON delay time: 55 us max. OFF delay time: 45 us max.
Lit.
Minimum operating time:
Approx. 100 us
Light Unit status
Pin 4 (PNP)
Not lit. Not lit.
High voltage
Open
ON delay time: 55 us max. OFF delay time: 45 us max.
Lit.
Minimum operating time:
Approx. 100 us
* Use an element or switch with a current ow of approximately 1 mA in the external circuit.
Logic Table
Refer to the following table for the low and high voltages.
Pin 4
Pin 3
(ground)
Switch,
relay, etc.
Pin 4
Pin 3
(ground)
Transistor
(PNP)
Optional Products (Sold Separately)9
Error Displays
8
If an error occurs, it will be shown on the digital display on the operating panel.
Digital display Status
E1 Overdrive error
In Overdrive Mode, the operating time or the ON signal repeat period limit was exceeded. This
error is shown on the digital display for 3 seconds. The mode indicator on the upper left of the
digital display will ash continuously.
(The mode indicator will stop ashing when you change to Constant Lighting Mode or when you
cycle the power supply.)
E2 Overload error An overload occurred, e.g., four or more Light Units were connected.
Outputting light will be stopped and automatic recovery will be attempted after 3 seconds.
Restrictions in Overdrive Mode
Depending on the set light intensity, the operating time and the repeat period of the signal that lights the Light Unit (i.e., the
ON signal) are restricted. Input ON signals that meet the conditions given in the following table.
*1 If the ON signal exceeds the above operating time (T
L
),
the light will be turned OFF automatically.
*2 If the ON signal is input in less time than the above
period, it will be ignored.
Light intensity Operating time (TL)*1 ON signal repeat period*2
0 to 28 125 ms max. At least 6.7 times the operating time
29 to 99 10 ms max. At least 14.3 times the operating time
If the ON signal is input continuously, the light will repeatedly turn ON and OFF.
Light Unit
status
ON signal
6.7 or 14.3 times T
L
6.7 or 14.3 times T
L
6.7 or 14.3 times T
L
Not lit.
Lit.
Not lit.
Lit. Lit.
Not lit. Not lit.
ON delay time: 55 us max.
T
L
: Operating time
(125 ms max. or 10 ms max.)
: Invalid ON signals
T
L
T
L
T
L
ON delay time: 55 us max. ON delay time: 55 us max.
Common Specications
Specications by Model
Main Specifications
11
Input voltage (rating) 24 VDC
Input voltage (range) 22.8 to 26.4 VDC
Input current (rating)* Constant lighting mode: 1.3A max.
Overdrive mode: 6A max.
Input connector M12 (5 pins, plug)
Output connector M12 (5 pins, socket)
Lighting mode Constant lighting mode, overdrive mode
Inrush current (max.) 6 A from a cold start
Insulation withstand voltage
(input and output-case)
250 VAC for one minute, cutoff current: 10 mA,
500 VDC, 1MΩ min.
Operating temperature
and humidity (indoors only)
Temperature: 0 to 40°C, Humidity: 20% to
85% (with no condensation)
Storage temperature
and humidity
Temperature: −20 to 60°C, Humidity: 20%
to 85% (with no condensation)
Vibration resistance
Acceleration: 19.6 m/s
2
, frequency: 10 to 55 Hz,
cycles: 3 minutes,sweep cycle: for 1 hour
each in X, Y, and Z directions
Shock
Acceleration: 800 m/s2, Application time: 11 ms,
Repetitions: 3 times each in 6 directions
Cooling method Natural air cooling
CE Marking
Safety standard: Conforms to EN62471
EMS standard: Conforms to EN61000-6-2
EMI standard: Conforms to EN61000-6- 4
Environmental regulations
RoHS compliant
Case material Aluminum alloy, resin
Weight 500 g
Accessories Instruction Guide
Model LED
color
Peak wavelength /
Correlated color
temperature (typ.)
Power
consumption
(W)(max.)
Protective
structure
LDLB-300SW-N
White 6100 K 31
-
LDLB-300RD-N
Red 630 nm 24
-
LDLB-IP-300SW-N
White 6100 K 31
Conforms to IP67
(JIS C 0920)
LDLB-IP-300RD-N
Red 630 nm 24
Conforms to IP67
(JIS C 0920)
* Recommended tightening torque: 0.7 N·m
*
*
The dimensions shown on the left include
tolerance. If you mount two Light Units with
their short sides adjacent to each other, you
can separate the centers of the installation
holes by 8 mm to eliminate misregistration.
4 x Ø4.5
(For installation)
313
304
63
3.5
3.5
Sealing Cap: PROT-M12 (PHOENIX CONTACT)
(For LDLB-IP Series)
300 (発光面)
24 (Emitting surface)
10
320
70
11
Bottom view
Rear view
Top vie w
8
32
Side view
8(0.6)
54
8
8
Headquarters
Address any product queries to the following address or to your nearest CCS representative.
* The power supply for daisy-chained Light Units must provide
sufcient output for all of the Light Units.
7
10
7
ON/OFF Inputs
DimensionsON/OFF Inputs (Continued)
Light Unit
status
ON signal
TL
6.7 or 14.3 times TL
Not lit.
Lit. Lit.
Not lit.
Not lit.
Light Unit
status Not lit. Not lit.
ON signal
ON delay time: 55 us max. OFF delay time: 45 us max.
Lit.
TL
Input Connector (M12 Plug) Conguration
5
4
1
3
2
Pin No. Signal
Cable
FECB-M12-5F Series
Wire color
1 24 VDC Brown
2 ON/OFF input (NPN) White
3Common ground Blue
4 ON/OFF input (PNP) Black
5 Analog input (0 to 10 V) Gray
EXCEPT FOR THE EXPRESS WARRANTIES STATED IN THIS DOCUMENT, CCS MAKES NO
ADDITIONAL WARRANTIES, E XPRESS, IM PLIED, OR STATUTORY, AS TO ANY MATTER
WHATSOE VER. IN PARTICUL AR, A NY AN D ALL WARRA NTIES OF MERCHANTABILIT Y
OR FITNESS FOR PARTICUL AR PU RPOSE ARE E XPRESSLY EXCLUDED.
EXCEPT AS EXPRESSLY SET FORTH HEREIN, CCS MAKES NO WARRA NTIES WITH RE-
SPECT TO THE PRODUCTS.
WARR ANT Y PERI OD: TWO YEARS (ONE Y EAR FOR RADIANT QUANTITY), STARTING
FROM CCS I nc. SH IPPING DATE.
CCS Inc. WILL R EPAIR OR R EPLACE THE PRODUCT FREE OF CHARG E IF IT SH OULD
FAIL TO FUNCTION O R IF THE RADIANT QUANTITY OF THE PRO DUCT SHOULD DROP
TO 50% OR LESS OF ITS INITIAL RADIA NT QUANTIT Y WITHIN THE S PECIFIED WARR AN -
TY PERIOD. IF EITH ER OF THESE CONDITIONS OCCURS, PLEASE TAKE THE PRODUCT
TO YOUR CCS SALES REPRESENTATIVE.
WARRANTY TERMS
1 CCS Inc. WILL REPAIR OR REPLACE THE PRODUCT FREE OF CHARGE IF IT SHOU LD
FAIL TO FUNCTION U NDER USE ON OUR SPECIFIED CONDITION IN ACCORDANCE
WITH TH E INSTRUCTION GUIDE AND OTHER WRITTEN CAUTIONS DURING THE INDI-
CATED WARR ANT Y PERIOD OF T WO YE ARS.
2 CCS Inc. WILL REPAIR OR REPLACE THE PRODUCT FREE OF CHARGE IF ITS R ADIANT
QUANTITY SHOULD DROP TO 50% OR LESS OF ITS INITIA L RADIANT QUANTITY UN-
DER USE O N OUR SPECIFIED CONDITION IN ACCORDA NCE WITH THE INSTRUCTION
GUIDE AND OTH ER WRITTEN CAUTIONS DURING THE INDICATED WARR ANTY PERI-
OD OF ON E YEA R.
3 CCS Inc. WILL CHARGE A REPAIR FEE UNDER THE FOLLOWING CONDITION S:
1) IF THE PROD UCT HAS BEEN SUBJECTED TO MISUSE, UN AUTHO RIZED REPAIRS,
OR MODIFICATION FROM ITS ORIGINAL DESIGN.
2)
IF THE PRODUCT HAS BEEN DAMAG ED FROM IMPACTS DUE TO INA PPROPRIATE HAN-
DLING.
3) IF DAMAGE TO THE PRODUCT RESULTS FROM EX TERN AL CAUSES INCLUDING
ACCIDENTS, FIRE, POLLUTIO N, RIOTS, COM MUNICATION FAILURES, E ARTH-
QUAKES, THUNDERSTORMS, WIND A ND FLOOD DAMAG E, OR ANY OTHER ACT OF
PROVIDENCE, OR FROM ANY EX TRAORDI NARY CONDITIONS SUCH AS ELECTRICAL
SURGES, WATER LEAKAGE, CONDENSATION, OR THE USE OF CHEMICALS.
4) IF THE DAMAGE RESULTS FROM CONNECTION TO ANY Control Unit OR TO AN Y EQUIPMENT
WHICH CCS Inc. DOES NOT MANU FACTURE O R DOES NOT SPECIFY FOR US E.
4
CCS ASSUMES NO LIABILIT Y FOR ANY PURCHASER’S SECONDA RY DAMAGE (DAM AGE
OF
EQUIPMENT, LOSS OF OPPORTUNITIES, LOSS O F PROFITS, ETC.) OR ANY OTHER
DAMAGE RESULTING FROM A FAILU RE OF OUR PRODUCT.
THIS WARRA NTY INFOR MATION PROVIDES THE SCO PE OF CC S'S PRODUCT WARR AN-
TY WITHIN THE SPECIFIED PERIOD, AN D DOES NOT INDICATE OR IMPLY ANY FURTH ER
GUAR ANTEE BEYOND THE WARRANTY TERMS.
CONTACT CCS FOR INQ UIRIES OR INFORMATION ON REPAIRS TO THE PRODUCT AF-
TER THE EXPIRATION O F THE WARRA NTY.
NOTE: THE RADIANT QUANTITY REFERS TO THE WATTAGE OF PHYSICAL ENERGY R ADI ATED
FROM AN LED. IT REFERS TO THE RADIATION LUMINOSITY OF THE LED MEASURED
UNDER CONDITIONS SPECIFIED BY CCS OR THE R ADIATION ILLUMINATION OF THE LED
UNDER SPECIFIED IRR ADIATION CO NDITIONS. CCS SPECIFIES THE R ADIANT QUANTITY
FOR EACH LED LIGHT BECAUSE THE MEASUREMENT AND IRR ADIATION CONDITIONS
VARY FROM THE FORM, THE APPLICATION AND THE IRRADIATION WAVELENGTH.
Warranty Information
Copyright© 2016 CCS Inc. All Rights Reserved.
Descriptions in this instruction guide are based on information available as of July 2016. KZ06922-T001-003
Shimodachiuri-agaru, Karasuma-dori, Kamigyo-ku,Kyoto 602-8011 Japan
E-mail : intlsales@ccs-inc.co.jp
Phone : +81-75-415-8284 Fax : +81-75-415-8278
Use our website to nd your nearest CCS representative.
http://www.ccs-grp.com/mvad
C ontent s of this Instruction Guide may be changed without prior notice.
Illustrations used in this Instruction Guide may differ from ac tual products.
CCS maintains the copyright on this Instruction Guide. Unauthorized transfer or reproduction is strictly prohibited.
Instruction Guide and Dimensional Diagrams in PDF or CAD can be downloaded from the CC S website. http://www.ccs-grp.com
Information Required for China RoHS Directive
环保
使用期限 产品
有害物质的名称及含量
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(C r ( VI ))
多溴联 苯
(PB B)
多溴二 苯醚
(PBDE)
LED 照明
( 本表格依据 SJ/T11364 的规定编制。)
：
表示该有毒有害物质在该部件所有均质材料中的含量均在 GB/T26572 标准规定的限量要求以下。
：
表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T26572 标准规定的限量要求。
( 注 ) 铅和镉中的“×”，因欧洲 Ro HS 没限定，故用“○”表示。
Usage deadline for environmental protection
The number used in this logo is based on “Management Methods for Restricting Hazardous Substances Used
in Electric and Electronic Products” and related regulations from People’s Republic of China. It shows the
product usage duration in years for environmental protection. After nishing a product usage, the product
needs to be re-used or discarded appropriately following local law and regulations, complying with safety and
usage caution.
Usage Deadline
for Environmental
Protection
Product
name
Names and contents of hazardous substances
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
chromium (Cr(VI))
PBB PBDE
LED
Lights
(This table is made in c ompliance with SJ/T11364 regulations.)
: Indicates that this toxic or hazardous subst ances contained in all the homogeneous
materials for this par t, according to GB /T26572 is within the limit requirement.
: Indicates that this tox ic or hazardous substance c ontained in all the homogeneous materials
for this part, according to GB/ T26572, is over the limit requirement.
*Lead and cadmium are exc luded in EU RoHS.
Names and contents of hazardous substances 产品中有害物质的名称及含量
环保使用期限
此标志的数字是根据中华人民共和国电器电子产品有害物质限制使用管理办法以及有关标准等，表示该产品的环
保使用期限的年数。
遵守产品的安全和使用上的注意，在产品使用后采取适当的方法根据各地法律，规定，回收再利用或进
行废弃处理。
Ø14.8
44 n x 1000 50
(Ø 5.1)
(n=1, 2, 3, 5)
(Unit: mm)
(Unit: mm)
Light Unit (input connector)
(Socket)
Input connector
(Socket)
Output connector
(Plug)
Flying leads
(5 wires, AWG22)
Ø14.8
(Ø 5.1)
Ø14.8
44 600 46.8
Input Cable Link Cable
Model: FECB-n-M12-5F Model: FECB-0.6-M12-5M-5F
This cable is used to supply power to the Light Unit and to input sig-
nals to control the light intensity and turn the light ON and OFF.
Use this cable for daisy-chain connections.
Select the required cable length.
Weight: 50 g max.
Model
FECB-1-M12-5F FECB-2-M12-5F FECB-3-M12-5F FECB-5-M12-5F
Length 1 m 2 m 3 m
5 m
Weight 55 g max. 90g max. 130g max. 210g max.
All manuals and user guides at all-guides.com
