CeraGem CGM MCB-1201 User manual

Important safety issues
1
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the appliance.
The information below stands to protect the safety of the user and to prevent any property
damage. All users must read the manual and use the product appropriately. The important safety
issues are divided into“Danger”, “Warning” and “Caution” and their meanings are as follows. This
picture is a symbol used to warn in case of dangerous situations or dangerous control methods.
Danger
Danger
Warning
Caution
In case of violating the instructions, there is an emergent possibility of serious
damage or even death.
In case of violating the instructions, there is some possibility of serious injury
or death.
In case of violating the instructions, there is possibility of minor injury or
property damage.
1. While using this product, do not use pins or other metals.
2. Do not use the product when there is humidity or water.
3. The external projector must be used with the external projector cover so that there is no
direct contact between the product and skin. (There is risk of receiving a burn.)
4.
To prevent damage to the eye (eyeball), do not place the external projector directly on the eye.
5. In case of thunder, lightning or an earthquake, please stop using the product and unplug it.
(There is risk of receiving an electric shock or a burn.)
6. Do not pull the cord to unplug or touch the power plug with wet hands.
(There is risk of receiving an electric shock or a burn.)
7. Apart from the mode for massaging the abdomen or the manual mode, do not use the
product laying face down.
(If the product is used lying down, do not use near the rib cage and only on the abdomen.)
Please follow the instructions carefully in order to reduce potential electric shocks.
Be careful not to get burned from unintended use.
The least favorable working condition is to use the thermal and massaging functions
continuously while applying 135kg on the main mat and the auxiliary part.
The least favorable working condition

Important safety issues
2
Important safety issues
3
Warning
In order to prevent injuries from burns, fires and electric shocks, one must connect
to a socket that has a ground connection. Be certain of how to connect to the
socket before using the product.
1. Only use the product if it is in mechanically complete condition.
If damaged products are used, there is a possibility of injury or burns)
2. If you have finished using the product or will not use it for a long time, unplug the product.
3. Apart from the external projector cover provided by our company, do not place other products
or substances on top that may cause fires (such as fiber products, blankets and etc.)
(Overheating can cause fires and electric shocks.)
4. In case of use by a disabled person or children, guardians must be present.
*Warning! Keep children away from where this product has been installed.
*Warning! Make sure that children do not jump on the thermal massage bed.
5. Do not use the product if they are in the conditions mentioned below. Call the customer
center and request inspection or after-service.
- If the product has been dropped or is damaged
- If the product is wet
- If the cord or the power button is damaged. (There is a risk of an electric shock or a fire.)
6. Keep the power cord away from electric heating appliances or heaters.
7. This product has only been designed for indoor use. Do not use it outdoors.
8. Do not use the product where there are foreign substances in the air or places that handle oxygen.
9. Do not use or apply skin care, cosmetic or medical products on your skin before and during
the usage of this product.
10. Be cautious of heated surfaces. (Can cause severe burns)
11. Do not use the external projector on parts of the body that have low levels of sensitivity or
parts that have reduced blood flow.
(The heat remaining from the product may be dangerous to children or those who are in bad health.)
12. Please do not sleep on the equipment.
13. Do not randomly disassemble, repair or remodel the product. Call the customer center when
in need of a repair.
(There is a risk of electrick shock, fire, injury, and burns.)
14. To avoid the risk of injury:
- Pregnant women, people who have malignancies, high fever, osteoporosis, people in
poor physical health, people in poor physical shape or undergoing any medical treatment,
and people suffering back, neck, shoulder or hip pain should consult their doctor before
using the product.
- If you have a pacemaker, defibrillator, other artificial implants or other medical devices,
consult with your doctor prior to use.
- If you have sensitive reactions or allergy to heat, you should also consult your doctor
before using the product.
- Do not use on bare skin; always wear clothing.
- Do not use if you have had any major surgeries, including back and/or hip surgeries.
- Consult your doctor prior to use if you have any external wound(s) or infection(s) on
the skin where the product will come into direct contact with your skin.
- Immediately stop using the unit if you start to feel sick or uncomfortable, or if the
massage seems too painful.
- As of now, there is no evidence to suggest that this product interferes with or influences
medications. Those taking any prescribed medications should consult their doctor before
using this product.
- Do not go to sleep while using the unit.
- Do not use the unit after drinking alcohol.
- Do not allow children or pets to play on or around the unit, especially during operation.
Caution
1. When using the internal projector, do not twist your body and use it with a straight posture.
2. When the product is set to high temperatures, there is a risk of burns, so set the projector’s
temperature at an optimal level. (Depending on the physical constitution or thickness of skin,
use the product at optimal temperature.)
3. Those with sensitive skin must use the product at lower temperatures. (There is a risk of burns)
4. Children, those who cannot control the temperature by themselves, and those who have weak
sensory skin must be cautious of using the product for an extended period even if it is set at a low
temperature because there is risk of receiving a burn. (Warning! Please use while wearing clothing.)
5. If there are any abnormal symptoms while using the product, you must consult a doctor
before using it again.
6. Do not bend the power cord or the outer wiring by force. (There is a risk of electric shocks and fires.)
7. Do not place flammable objects (candles, cigarettes and alcohol), objects with water in them,
heavy objects or sharp objects on top of the product. (They can cause electric shocks and damage.)
8. When climbing on or off the product, be cautious of the risk of falling.
9. Use according to the instruction manual and keep to the duration and methods instructed in the manual.
(Use 1~2 times a day and do not use other products unless supplied by the manufacturer.)
10. Do not use the external projector(s) for more than 2~3 minutes on one part of the body.
(The projector must be moved to another part of the body after 2~3 minutes.)
11. Do not apply shock to the product.
12. Do not throw the rmote control and swing or swirl the connecting cable.
(It can cause the injury and equipment failure.)
13. When you move or store the product, take care not to throw down it.
(It can cause the injury and equipment failure.)
14. The appliance has a heated surface. Persons insensitive to heat must be careful when using the appliance.
15. Do not jump on the product.
(It can cause the injury and equipment failure.)
16. The Automatic Thermal Massager is intended for muscle relaxation therapy by delivering heat and a
soothing massage to the applied areas.
※ Important information on symptoms
In some cases there may appear a so-called “initial aggravation“. This initial aggravation may begin with a
subjective increase of symptoms prior to the desired healing. The effect of initial aggravation is also known
from other treatments (for e.g. the science of homoeopathy), which is defined as the reaction of healing and
/ or the clearing of blockages. The initial aggravation that may occur does not constitute an exclusion
criterion of the application of product.
In the case of excessive pain related to pre-existing spinal conditions, distinct hypertension, cardiovascular
diseases or dizziness, please first reduce the intensity of usage (duration & temperature).
In cases in which the initial worsening leads to excessive continual pain please stop the therapy and consult
a medical doctor immediately to clarify if and under which circumstances the therapy can be continued or ceased.

Important safety issues
2
Important safety issues
3
Warning
In order to prevent injuries from burns, fires and electric shocks, one must connect
to a socket that has a ground connection. Be certain of how to connect to the
socket before using the product.
1. Only use the product if it is in mechanically complete condition.
If damaged products are used, there is a possibility of injury or burns)
2. If you have finished using the product or will not use it for a long time, unplug the product.
3. Apart from the external projector cover provided by our company, do not place other products
or substances on top that may cause fires (such as fiber products, blankets and etc.)
(Overheating can cause fires and electric shocks.)
4. In case of use by a disabled person or children, guardians must be present.
*Warning! Keep children away from where this product has been installed.
*Warning! Make sure that children do not jump on the thermal massage bed.
5. Do not use the product if they are in the conditions mentioned below. Call the customer
center and request inspection or after-service.
- If the product has been dropped or is damaged
- If the product is wet
- If the cord or the power button is damaged. (There is a risk of an electric shock or a fire.)
6. Keep the power cord away from electric heating appliances or heaters.
7. This product has only been designed for indoor use. Do not use it outdoors.
8. Do not use the product where there are foreign substances in the air or places that handle oxygen.
9. Do not use or apply skin care, cosmetic or medical products on your skin before and during
the usage of this product.
10. Be cautious of heated surfaces. (Can cause severe burns)
11. Do not use the external projector on parts of the body that have low levels of sensitivity or
parts that have reduced blood flow.
(The heat remaining from the product may be dangerous to children or those who are in bad health.)
12. Please do not sleep on the equipment.
13. Do not randomly disassemble, repair or remodel the product. Call the customer center when
in need of a repair.
(There is a risk of electrick shock, fire, injury, and burns.)
14. To avoid the risk of injury:
- Pregnant women, people who have malignancies, high fever, osteoporosis, people in
poor physical health, people in poor physical shape or undergoing any medical treatment,
and people suffering back, neck, shoulder or hip pain should consult their doctor before
using the product.
- If you have a pacemaker, defibrillator, other artificial implants or other medical devices,
consult with your doctor prior to use.
- If you have sensitive reactions or allergy to heat, you should also consult your doctor
before using the product.
- Do not use on bare skin; always wear clothing.
- Do not use if you have had any major surgeries, including back and/or hip surgeries.
- Consult your doctor prior to use if you have any external wound(s) or infection(s) on
the skin where the product will come into direct contact with your skin.
- Immediately stop using the unit if you start to feel sick or uncomfortable, or if the
massage seems too painful.
- As of now, there is no evidence to suggest that this product interferes with or influences
medications. Those taking any prescribed medications should consult their doctor before
using this product.
- Do not go to sleep while using the unit.
- Do not use the unit after drinking alcohol.
- Do not allow children or pets to play on or around the unit, especially during operation.
Caution
1. When using the internal projector, do not twist your body and use it with a straight posture.
2. When the product is set to high temperatures, there is a risk of burns, so set the projector’s
temperature at an optimal level. (Depending on the physical constitution or thickness of skin,
use the product at optimal temperature.)
3. Those with sensitive skin must use the product at lower temperatures. (There is a risk of burns)
4. Children, those who cannot control the temperature by themselves, and those who have weak
sensory skin must be cautious of using the product for an extended period even if it is set at a low
temperature because there is risk of receiving a burn. (Warning! Please use while wearing clothing.)
5. If there are any abnormal symptoms while using the product, you must consult a doctor
before using it again.
6. Do not bend the power cord or the outer wiring by force. (There is a risk of electric shocks and fires.)
7. Do not place flammable objects (candles, cigarettes and alcohol), objects with water in them,
heavy objects or sharp objects on top of the product. (They can cause electric shocks and damage.)
8. When climbing on or off the product, be cautious of the risk of falling.
9. Use according to the instruction manual and keep to the duration and methods instructed in the manual.
(Use 1~2 times a day and do not use other products unless supplied by the manufacturer.)
10. Do not use the external projector(s) for more than 2~3 minutes on one part of the body.
(The projector must be moved to another part of the body after 2~3 minutes.)
11. Do not apply shock to the product.
12. Do not throw the rmote control and swing or swirl the connecting cable.
(It can cause the injury and equipment failure.)
13. When you move or store the product, take care not to throw down it.
(It can cause the injury and equipment failure.)
14. The appliance has a heated surface. Persons insensitive to heat must be careful when using the appliance.
15. Do not jump on the product.
(It can cause the injury and equipment failure.)
16. The Automatic Thermal Massager is intended for muscle relaxation therapy by delivering heat and a
soothing massage to the applied areas.
※ Important information on symptoms
In some cases there may appear a so-called “initial aggravation“. This initial aggravation may begin with a
subjective increase of symptoms prior to the desired healing. The effect of initial aggravation is also known
from other treatments (for e.g. the science of homoeopathy), which is defined as the reaction of healing and
/ or the clearing of blockages. The initial aggravation that may occur does not constitute an exclusion
criterion of the application of product.
In the case of excessive pain related to pre-existing spinal conditions, distinct hypertension, cardiovascular
diseases or dizziness, please first reduce the intensity of usage (duration & temperature).
In cases in which the initial worsening leads to excessive continual pain please stop the therapy and consult
a medical doctor immediately to clarify if and under which circumstances the therapy can be continued or ceased.

Ground connection method
4
Danger
Contents
5
This product must be connected to a ground connection.
The ground connection reduces resistance against electric currents in case there are any
defects or breakdowns which may lead to electric shocks and damage. On the product,
there are conductors and electric terminals where the power cord is located. The power
cord has been installed to comply with regional laws; therefore it must be connected to
where there is a socket.
Check the connection of the product.
(Inappropriate connection may lead to electric shock and damage.)
If you suspect that the product’s power cord and connection point
has a problem, request investigation from an electrician or service
personnel. This product is for 100-240V~ and the power terminal is
installed as can be seen in the picture on the right. Connect the
power cord to a socket that looks like the one shown in the picture.
This product does not use an adaptor.
Notice to users
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limit for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equ-
ipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particular
installation, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Caution
- Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
>> Important Safety Issues
1. Product’s characteristics
2. The name of each part
Ⅰ. Introduction of the product 07
1. Check product’s composition
2. Check before product installation
3. Installation
4. Check after installation
Ⅱ. Installation and preparation 11
1. Remote control layout
2. How to use the remote control
3. How to use the product (by mode)
4. How to move the product
Ⅲ. Using the product 17
1. Self inspection
2. Management techniques and storage methods
3. Check before A/S request
4. Remote control error messages
5. Product specifications
6. Product warranty
Ⅳ. Management and matters that require attention 31
- Danger
- Warning
- Caution
01
Ⅴ. Service manual 39

Ground connection method
4
Danger
Contents
5
This product must be connected to a ground connection.
The ground connection reduces resistance against electric currents in case there are any
defects or breakdowns which may lead to electric shocks and damage. On the product,
there are conductors and electric terminals where the power cord is located. The power
cord has been installed to comply with regional laws; therefore it must be connected to
where there is a socket.
Check the connection of the product.
(Inappropriate connection may lead to electric shock and damage.)
If you suspect that the product’s power cord and connection point
has a problem, request investigation from an electrician or service
personnel. This product is for 100-240V~ and the power terminal is
installed as can be seen in the picture on the right. Connect the
power cord to a socket that looks like the one shown in the picture.
This product does not use an adaptor.
Notice to users
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limit for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equ-
ipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particular
installation, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Caution
- Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
>> Important Safety Issues
1. Product’s characteristics
2. The name of each part
Ⅰ. Introduction of the product 07
1. Check product’s composition
2. Check before product installation
3. Installation
4. Check after installation
Ⅱ. Installation and preparation 11
1. Remote control layout
2. How to use the remote control
3. How to use the product (by mode)
4. How to move the product
Ⅲ. Using the product 17
1. Self inspection
2. Management techniques and storage methods
3. Check before A/S request
4. Remote control error messages
5. Product specifications
6. Product warranty
Ⅳ. Management and matters that require attention 31
- Danger
- Warning
- Caution
01
Ⅴ. Service manual 39

6
MEMO
7
Ⅰ. Introduction
of the product
1. Product’s characteristics
2. The name of each part

6
MEMO
7
Ⅰ. Introduction
of the product
1. Product’s characteristics
2. The name of each part

Handle
1. Product’s characteristics
8
2. The name of each part
9
External Projector (3-Sphere)
(Applied part)
Remote Control
Connector
External Projector
Connector
Remote Control
Safety Latch
Supporting Frame
Main Heating
Element
Remote control
1. Aesthetically Pleasing, Easy-To-Use Exterior Design
The aesthetically pleasing, easy-to-use exterior design matches well with any
home interior article. The folding design of the supporting mat requires
minimum space and ensures convenience for the user.
3. Easy-To-Move Casters Installed
When the product is not in use, you can easily move and store it by using the
casters installed underneath.
4. Diverse Stimulation Programs
The different stimulation programs created based on the concept of alternative
medicine allow users to select programs that b needs.
5. Slim, Easy-To-Use Remote Control
The slim and light remote control has function keys in the form of icons for
more convenient product operation and simpler manipulation. Moreover, with
its acceptable-type design for the main body, the risk of loss is minimized.
6. External Projectors (3-Sphere) Provided
External projectors that can be used while this massaging equipment is
operated are provided as basic components; users may use the external
projectors for the abdomen, shoulders, arms, legs, and other body parts.
2. Body sensing function
The new body sensing function automatically measures the length of the spine
of the user, offering optimal, customized compressive stimulation.
Internal
Projector
Sensor for the opening of
auxiliary part detection
*Sensor for the opening of auxiliary part detection : It detects that the auxiliary part is open.
When the sensor is separated from the body (when you lift or close the auxiliary part),
however, it does not work.
Main body mat
(Applied part)
Auxiliary Part
Outer Fabric

Handle
1. Product’s characteristics
8
2. The name of each part
9
External Projector (3-Sphere)
(Applied part)
Remote Control
Connector
External Projector
Connector
Remote Control
Safety Latch
Supporting Frame
Main Heating
Element
Remote control
1. Aesthetically Pleasing, Easy-To-Use Exterior Design
The aesthetically pleasing, easy-to-use exterior design matches well with any
home interior article. The folding design of the supporting mat requires
minimum space and ensures convenience for the user.
3. Easy-To-Move Casters Installed
When the product is not in use, you can easily move and store it by using the
casters installed underneath.
4. Diverse Stimulation Programs
The different stimulation programs created based on the concept of alternative
medicine allow users to select programs that b needs.
5. Slim, Easy-To-Use Remote Control
The slim and light remote control has function keys in the form of icons for
more convenient product operation and simpler manipulation. Moreover, with
its acceptable-type design for the main body, the risk of loss is minimized.
6. External Projectors (3-Sphere) Provided
External projectors that can be used while this massaging equipment is
operated are provided as basic components; users may use the external
projectors for the abdomen, shoulders, arms, legs, and other body parts.
2. Body sensing function
The new body sensing function automatically measures the length of the spine
of the user, offering optimal, customized compressive stimulation.
Internal
Projector
Sensor for the opening of
auxiliary part detection
*Sensor for the opening of auxiliary part detection : It detects that the auxiliary part is open.
When the sensor is separated from the body (when you lift or close the auxiliary part),
however, it does not work.
Main body mat
(Applied part)
Auxiliary Part
Outer Fabric

10
MEMO
11
Ⅱ. Installation
and preparation
1. Check product’s composition
2. Check before product installation
3. Installation
4. Check after installation

10
MEMO
11
Ⅱ. Installation
and preparation
1. Check product’s composition
2. Check before product installation
3. Installation
4. Check after installation

1. Install where the ground is flat to avoid the risk of damaging the product.
2. Try and avoid installation where there is a lot of humidity or dust.
(To avoid risking electric shocks or fire.)
3. Install according to the designated order.
5. Do not drop the product or apply any force to it.
(This could cause malfunctioning.)
4. When installing, check that the rated voltage is 100-240V~
(To avoid circuit damage or fire.)
6. Do not use damaged power cords, plugs or old sockets.
7. You must connect to a socket with a connection terminal.
(To avoid risking electric shocks.)
1. Check product’s composition
12
2. Check before product installation
13
1
2
3
4
5
6
7
8
External projectors (3-Sphere)
Easy to use on body parts such as the abdomen, shoulders, arms,
legs and etc. Can be used with the main product or shared
between two people.
External projector cover
It can be used while covering the external projector.
Remote control
Simple to operate and check the product’s status.
Remote control back label
Describes the remote control button layout, and can be attached
to the back of the remote control.
Power cord
Connects with the main body and plugs into an outlet for use.
User manual
Information on how to use the product.
Outer fabric
Protects the product from pollution and prevents burns. Easy to
wash as it is detachable.
12
Remote control cable
To use the remote control, connect it to the main body.

1. Install where the ground is flat to avoid the risk of damaging the product.
2. Try and avoid installation where there is a lot of humidity or dust.
(To avoid risking electric shocks or fire.)
3. Install according to the designated order.
5. Do not drop the product or apply any force to it.
(This could cause malfunctioning.)
4. When installing, check that the rated voltage is 100-240V~
(To avoid circuit damage or fire.)
6. Do not use damaged power cords, plugs or old sockets.
7. You must connect to a socket with a connection terminal.
(To avoid risking electric shocks.)
1. Check product’s composition
12
2. Check before product installation
13
1
2
3
4
5
6
7
8
External projectors (3-Sphere)
Easy to use on body parts such as the abdomen, shoulders, arms,
legs and etc. Can be used with the main product or shared
between two people.
External projector cover
It can be used while covering the external projector.
Remote control
Simple to operate and check the product’s status.
Remote control back label
Describes the remote control button layout, and can be attached
to the back of the remote control.
Power cord
Connects with the main body and plugs into an outlet for use.
User manual
Information on how to use the product.
Outer fabric
Protects the product from pollution and prevents burns. Easy to
wash as it is detachable.
12
Remote control cable
To use the remote control, connect it to the main body.

3. Installation
14
3. Installation
15
5
부속품
Take out the product and components from the box. Components
1
Open the product using the supporting frame.
Take care not to insert any part of your body into the product when opening the product.
(There is risk of injury.)
3
Connect the outer fabric, remote control, and external projector properly.
4
Remote
Control
External
Projector
2Lay the product where the ground is flat and unlock the safety latch.
If the power cord is connected when the power switch is ”On”, it can cause mechanical failure.
Caution
Caution
Connect the power cord onto the main body and plug into a socket.
Do not touch the connector pin.
(Can cause bodily harm or mechanical failure.)
Warning
Accessaries
The supporting frame cannot open somewhat smoothly for safety reasons.
12

3. Installation
14
3. Installation
15
5
부속품
Take out the product and components from the box. Components
1
Open the product using the supporting frame.
Take care not to insert any part of your body into the product when opening the product.
(There is risk of injury.)
3
Connect the outer fabric, remote control, and external projector properly.
4
Remote
Control
External
Projector
2Lay the product where the ground is flat and unlock the safety latch.
If the power cord is connected when the power switch is ”On”, it can cause mechanical failure.
Caution
Caution
Connect the power cord onto the main body and plug into a socket.
Do not touch the connector pin.
(Can cause bodily harm or mechanical failure.)
Warning
Accessaries
The supporting frame cannot open somewhat smoothly for safety reasons.
12

Turn on power at the side of the main body.
(Turn off power when the product is not in use.)
2
1
3Press the power key of the remote control and check whether the
display turns on.
4. Check after Installation
16
1. Before connecting the power cord, connect the remote control first.
2. Set the temperature appropriately according to user when using the product.
3. After using the product, turn off power on the remote control, and then turn
off the main body.
1. Remote control layout
2. How to use the remote control
3. How to use the product by mode
4. How to move the product
Ⅲ. Using the
Product
17
12
*For the remote control’s screen,
refer to page 19.
Unfold the auxiliary part completely.
(The remote control will not work unless you unfold the auxiliary part.)
Caution
12

Turn on power at the side of the main body.
(Turn off power when the product is not in use.)
2
1
3Press the power key of the remote control and check whether the
display turns on.
4. Check after Installation
16
1. Before connecting the power cord, connect the remote control first.
2. Set the temperature appropriately according to user when using the product.
3. After using the product, turn off power on the remote control, and then turn
off the main body.
1. Remote control layout
2. How to use the remote control
3. How to use the product by mode
4. How to move the product
Ⅲ. Using the
Product
17
12
*For the remote control’s screen,
refer to page 19.
Unfold the auxiliary part completely.
(The remote control will not work unless you unfold the auxiliary part.)
Caution
12

12
18
2. How to use the remote control1. Remote control layout
19
Turning on the Remote Control
1. Check the condition of the product connections and press
the power key of the remote control.
- Press the remote control for 2~3 seconds to turn it off.
- Start the remote control after opening the auxiliary part.
2. Check the display on the remote control.
- External projectors appear only when they are connected.
- The current temperature is displayed, and the standby state is shown.
3. Select the mode to be used.
- Refer to pages 21~26 for the mode selection.
- Refer to page 20 for details on how to adjust the temperature.
Semi-automatic
mode button Internal/External projectors
button for selection
Power button
Semi-automatic
mode symbol
Manual mode symbol
Internal projector
position symbol
Automatic mode
button (Mode A)
Internal projector’s
temperature symbol
External projector’s
temperature symbol
Mode Symbol
Mode 1 button
Mode 2 button
Mode button
(Mode 3~9)
Up/Down button
Manual mode button
12
12

12
18
2. How to use the remote control1. Remote control layout
19
Turning on the Remote Control
1. Check the condition of the product connections and press
the power key of the remote control.
- Press the remote control for 2~3 seconds to turn it off.
- Start the remote control after opening the auxiliary part.
2. Check the display on the remote control.
- External projectors appear only when they are connected.
- The current temperature is displayed, and the standby state is shown.
3. Select the mode to be used.
- Refer to pages 21~26 for the mode selection.
- Refer to page 20 for details on how to adjust the temperature.
Semi-automatic
mode button Internal/External projectors
button for selection
Power button
Semi-automatic
mode symbol
Manual mode symbol
Internal projector
position symbol
Automatic mode
button (Mode A)
Internal projector’s
temperature symbol
External projector’s
temperature symbol
Mode Symbol
Mode 1 button
Mode 2 button
Mode button
(Mode 3~9)
Up/Down button
Manual mode button
12
12