Cerio OW-300N2-A2 User manual

CERIO Corporation
OW-300N2-A2
1000mW eXtreme Power 11N 300Mbps
Outdoor Access Point
User Manual

Table of Contents
1. Introduction.............................................................................................................5
1.1 Overview.....................................................................................................................................5
1.2 Applications in Wireless Network........................................................................................5
1.3 Features......................................................................................................................................7
2. AP Mode Configuration........................................................................................9
2.1 Choose Your Operating Mode ( AP Mode ).......................................................................9
2.2 External Network Connection.............................................................................................10
2.3 Configure OW-300N2-A2 LAN IP Address.......................................................................10
2.4 Wireless General Setup........................................................................................................12
2.5 Configure Wireless Advanced Setup................................................................................14
2.6 Create Virtual AP –Virtual AP Setup................................................................................19
2.8 WDS Setup - Expand your Wireless Network.................................................................28
2.9 WDS Status..............................................................................................................................28
2.10 Associated Clients.................................................................................................................29
3. WDS Mode Configuration..................................................................................30
3.1 Choose Your Operating Mode ( WDS Mode ) .................................................................30
3.2 External Network Connection ( Network Requirement )..............................................30
3.3 Configure OW-300N2-A2 LAN IP Address.......................................................................30
3.4 Wireless General Settings...................................................................................................32
3.5 Configure Wireless Advanced Setup................................................................................35
3.6 WDS Setup...............................................................................................................................40
3.7 WDS Status..............................................................................................................................41
4. Client Bridge + Repeater AP Mode Configuration......................................41
4.1 Choose Your Operating Mode(Client Bridge + Repeater AP) ....................................42
4.2 External Network Connection ( Network Requirement )..............................................42
4.3 Configure OW-300N2-A2 LAN IP Address.......................................................................42
4.4 Wireless General Setup........................................................................................................45
4.5 Configure Wireless Advanced Setup................................................................................46
4.6 Site Survey...............................................................................................................................51
4.7 Station Profile .........................................................................................................................52
4.8 Remote AP Status..................................................................................................................54
4.9 Repeater AP Setup.................................................................................................................54
4.10 Repeater AP MAC Filter Setup............................................................................................58
5. Router AP Mode Configuration........................................................................59
5.1 Choose Your Operating Mode ( Router AP Mode ).......................................................60
5.2 External Network Connection.............................................................................................60

5.3 Configure DDNS Setup.........................................................................................................65
5.4 Configure OW-300N2-A2 LAN IP Address.......................................................................65
5.5 Wireless General Setup........................................................................................................67
5.6 Configure Wireless Advanced Setup................................................................................69
5.7 Create Virtual AP –Virtual AP Setup................................................................................74
5.8 Virtual AP General Configuration......................................................................................75
5.9 WDS Setup - Expand your Wireless Network.................................................................83
5.10 WDS Status..............................................................................................................................83
5.11 Associated Clients.................................................................................................................84
6. WISP + AP Mode Configuration.......................................................................84
6.1 Choose Your Operating Mode ( WISP + Repeater AP Mode )....................................84
6.2 External Network Connection ( Network Requirement )..............................................85
6.3 Configure CPE(WAN) Setup................................................................................................85
6.4 Configure OW-300N2-A2 LAN IP Address.......................................................................90
6.5 Configure DDNS Setup.........................................................................................................92
6.6 Wireless General Setup........................................................................................................92
6.7 Configure Wireless Advanced Setup................................................................................94
6.8 Site Survey...............................................................................................................................99
6.9 Station Profile .......................................................................................................................100
6.10 Remote AP Status................................................................................................................103
6.11 Repeater AP Setup...............................................................................................................103
6.12 Repeater AP MAC Filter Setup..........................................................................................107
7. System Management ........................................................................................108
7.1 Configure Management......................................................................................................109
7.2 Configure System Time......................................................................................................111
7.3 Configure UPnP Setup........................................................................................................112
7.4 Configure SNMP Setup.......................................................................................................113
8. Configure Advance Setup...............................................................................115
8.1 DMZ..........................................................................................................................................115
8.2 IP Filter....................................................................................................................................116
8.3 MAC Filter...............................................................................................................................118
8.4 Virtual Server.........................................................................................................................119
8.5 Parental Control ...................................................................................................................121
8.6 QoS..........................................................................................................................................123
8.7 IP Routing...............................................................................................................................124
8.8 Time Policy............................................................................................................................126
9. Configure Utilities Setup .................................................................................127
9.1 Profile setting........................................................................................................................127

9.2 Firmware Upgrade ...............................................................................................................128
9.3 Network Utility.......................................................................................................................130
9.4 PoE Bridge.............................................................................................................................130
9.5 Reboot.....................................................................................................................................131
10. Configure Status.........................................................................................132
10.1 Overview.................................................................................................................................132
10.2 DHCP Client...........................................................................................................................132
10.3 Extra Info................................................................................................................................133
10.4 Event Log...............................................................................................................................135
Appendix A. Windows TCP/IP Settings.........................................................137
Appendix B. WEB GUI Valid Characters............................................................139
Appendix C. MCS Data Rate.................................................................................143
Appendix D. Enabling UPnP in Windows XP.................................................144

1. Introduction
1.1 Overview
CERIO’s OW-300N2-A2 eXtreme Power 11n 2.4GHz 2x2 +10dBi + Heater Outdoor Bridge/Access
Point (1000mW) utilizes a built-in CenOS 3.0 software core and is compatible with CERIO
Wireless Management Software. Our CenOS 3.0 software core and CWMS management
software promotes operation efficiency and network management, making them very suitable for
outdoor wireless deployment. OW-300N2-A2 is the perfect outdoor device for reliably delivering
last mile wireless services to businesses or residential broadband subscribers.
OW-300N2-A2 utilizes 1000mW output Tx Power with built-in 10dBi patch antennas, and also
supports 2x2 external N-Type Antenna Connectors (users must enter the software UI to select
either built-in antennas or external N-Type antennas, they cannot be used simultaneously). This
device and use Wifi Mesh or WDS to provide clients with an Ethernet connection to an expanded
local wireless network. CERIO’s OW-300N2-A2 incorporates a built-in heater with smart
sensory control to detect when the device’s temperatures drop too low. This device is powered
through Power over Ethernet, allowing both data and power to be supplied through Cat5 cabling.
1.2 Applications in Wireless Network
Smart of PoE Bridge application
The CERIO OW-300N2-A2 incorporates Power over Ethernet Bridge function. PoE Bridge support
provide power to subsequent PD devices such as IP Cameras and Access Points . This
passthrough technology passes surplus electricity to other devices such as OW-2xxN2-Series /
OW-3xxN2-Series AP or other 48V PoE PD. PoE Bridge provides convenience and cost
reduction when setting up a wireless network.
CERIO’s OW-300N2-A2 eXtreme Power 11n 2.4GHz 2x2 +10dBi + Heater Outdoor Bridge/Access
Point (1000mW) supports 5 operation modes: Router AP mode/ Router AP + WDS mode, Pure
AP / AP + WDS Mode, Pure WDS Mode, Client Bridge + Universal Repeater AP Mode, and
finally WISP + Repeater AP Mode. CERIO’s OW-300N2-A2 utilizes built-in software interface and
is compatible with our remote management systems for simplified deployment, and reduction in
maintenance cost.

Wireless Architecture Mode
Router AP Mode (Gateway + Access Point + WDS)
Router AP without WDS , It can be deployed as a gateway with wireless Access Point
Router AP with WDS, It can be deployed as a gateway with wireless Access Point and provides
WDS link for network extension
Pure AP Mode & AP+WDS Mode
It can be deployed as a tradition fixed wireless Access Point
It allow wireless clients or Stations(STA ) to access
This enables the wireless interconnection of Access Point in an IEEE802.11 network. and
accept wireless clients at the same time
Pure WDS Mode (Repeater)
This enables the wireless interconnection of Access Point in an IEEE802.11 network
It allows a wireless network to be expanded using multiple access point without the need for a
wired backbone to link them
This also be referred to as repeater mode
It cannot allow wireless clients or Stations (STA) to access
Client Bridge + Repeater AP Mode
It can be used as an Client Bridge + Repeater AP to receive wireless signal over last mile
applications, helping WISPs deliver wireless broadband Internet service to new residential
and business customers.
In this mode, OW-300N2-A2 is enabled with DHCP Server functions. The wired clients of
OW-300N2-A2 are in the same subnet from Main Base Station and it accepts wireless
connections from client devices
WISP +AP Mode
Wi-Fi connection as WAN , in CPE mode , the device run as DHCP server to assign IP
address to clients out of a private IP address pool behind a NAT

It can be used as an Outdoor Customer Premises Equipment (CPE) to receive wireless signal
over last mile application, helping WISPs deliver wireless broadband Internet service to
residents and business customers
In the CPE mode, OW-300N2-A2 is a gateway enabled with NAT and DHCP Server functions.
The wired clients connected to OW-300N2-A2 are in different subnet from those connected to
Main Base Station, and, in CPE mode, it does not accept wireless association from wireless
clients.
1.3 Features
IEEE 802.11n Compliance in 2Tx / 2Rx Design
Enables Bandwidth of up to 300Mbps(Tx), 300Mbps(Rx) link rate
Support IEEE 802.11n, Operates in the 2.4GHz ISM Band
1000mW at 2.4Ghz eXtreme High Power
Built in +10dBi , 2.4GHz (H60, E60) Directional Panel Antenna
Support 2x2 External N-Type Antenna Connectors
Topology : Point to Point , Point to Multi Point
Support Over load current protection for the board design . and 3 LEDs Wireless Signal
Strength
Weather-Proof Housing (IP67/ 68 Approved)
Weather-Proof M-13 RJ45 Connector
Support Power over Ethernet (PoE) & PoE Bridge by LAN Port function.
Wide Range Voltage Input PoE Power support (12-68VDC)
Built-in lightning arrester (15kV ESD)
Built in Heater of automatically
Networking
Supports Static IP, Dynamic IP(DHCP Client) and PPPoE on Wi-Fi WAN Connection
Supports VPN Pass Throughput ( PPTP , IPSec , L2TP ) and MAC Cloning
Proxy DNS ,Dynamic DNS ,NTP Client
Virtual DMZ, Virtual Server (IP / Port Forwarding)
Supports IP / MAC Filter and Support Bandwidth traffic Shaping

Wireless Feature
Transmission power control : 1~100%
Channel selection : Manual or Auto
No of associated clients per AP : 32
Setting for max no associated clients : Yes
Supports 8 virtual ESSID and associated clients per AP to 32 and the Pure WDS Max. 4
Setting for transmission speed
Dynamic Wireless re-transmission
IEEE 802.11i Preauth (PMKSA Cache )
IEEE 802.11d -Multi country roaming
Channel Bandwidth setting : 20MHz or 20/40MHz
HT Tx/Rx Stream selection : 1 or 2
Short Slot support
Authentication/Encryption (Wireless Security)
Blocks client to client discovery within a specified VLAN
WEP 64/128 bit /EAP-TLS + Dynamic WEP , EAP-TTLS + Dynamic WEP
PEAP/MSPEAP + Dynamic WEP
WPA-PSK/TKIP,WPA-802.1x/TKIP, 802.11i WPA2-PSK/CCMP/AES 128/256bit,
WPA2 (802.1x /CCMP / AES 128/256bit ), No. of registered RADIUS servers : 1
Setting for TKIP/CCMP/AES 128/256bit (ASCII 63 & HEX 64 )key’s refreshing period
Hidden SSID broadcast support, and VLAN assignment on BSSID
Access Control list (ACL) by MAC Address
Quality of Service
Download and Upload traffic control and support Traffic Analysis and Statistics
Packet classifications via DSCP (Differentiated Services Code Point) and Support
IEEE802.11e WMM
Control Policy by IP/IP Ranges/ MAC/ Service , Layer-7 Protocol Support
No. of Max. Policy setting : 10
DiffServ/TOS , COS, IEEE 802.1Q Tag VLAN priority control

Management
Web-Based management interface, Intuitive Web Management Interface,
Administrative Access : HTTP and HTTPS and support CLI access via Telnet and SSH
Supports Firmware Upgrade via Web , Reset to Factory Defaults,
Supports SNMP v1/v2c/v3 , MIB II
UPnP (Universal Plug and Play)
NTP Time Synchronization
SNMP Traps to a List of IP Address
Support Event log
Antenna switchable control (use Built-in 10dBi patch or External antenna).
2. AP Mode Configuration
When AP mode is chosen, the system can be configured as an Access Point. This section provides
detailed explanation for users to configure in the AP mode with help of illustrations. In the AP mode,
functions listed in the table below are also available from the Web-based GUI interface.
2.1 Choose Your Operating Mode ( AP Mode )
OW-300N2-A2 Operating mode supports five operation modes: Router AP mode, AP mode,
WDS mode, CPE mode and Client Bridge + Repeater AP mode, respectively with built-in
remote management features.
The system administrator can set the desired mode via this page, and then configure the system
according to their deployment needs, Please click on System -> Operating Mode and follow the
below setting.

2.2 External Network Connection
Network Requirement
Normally, OW-300N2-A2 connects to a wired LAN and provides a wireless connection point to
associate with wireless client. Then, Wireless clients could access to LAN or Internet by
associating themselves with OW-300N2-A2 set in AP mode.
2.3 Configure OW-300N2-A2 LAN IP Address
Here are the instructions to setup the local IP Address and Netmask
Please click on System -> LAN and follow the below setting.
Ethernet Connection Type
Check either “Static IP” or “Dynamic IP” button as desired to set up the system IP of LAN port.

Static IP: The administrator can manually setup the LAN IP address when static IP is
available/ preferred.
IP Address : The IP address of the LAN port; default IP address is 192.168.2.254
IP Netmask : The Subnet mask of the LAN port; default Netmask is 255.255.255.0
IP Gateway : The default gateway of the LAN port
Dynamic IP: This configuration type is applicable when the OW-300N2-A2is connected
to a network with the presence of a DHCP server; all related IP information will be
provided by the DHCP server automatically.
Hostname : The Hostname of the LAN port.
DNS: Check either “No Default DNS Server” or “Specify DNS Server IP” button as desired
to set up the system DNS.
Primary : The IP address of the primary DNS server.
Secondary : The IP address of the secondary DNS server.
802.1d Spanning Tree
The spanning tree network protocol provides a loop free topology for a bridged LAN between
LAN interface and 8 WDS interfaces from wds0 to wds7. The Spanning Tree Protocol, which
is also referred to as STP, is defined in the IEEE Standard 802.1d
Click Save button to save your changes. Then click Reboot button to activate your changes.

2.4 Wireless General Setup
The administrator can change the data transmission, channel and output power settings for the
system. Please click on Wireless -> General Setup and follow the below setting.
MAC Address : The MAC address of the Wireless interface is displayed here.
Band Mode : Select an appropriate wireless band; bands available are 801.11 b/g/n mixed
mode
Country : a region, the OW-300N2-A2 support region for US,ETSI and Japan
Channel : Choosing the best WiFi channel
Auto Scan : Smart channel judgment, the function can auto choose use best Channel
AP List : the function support search neighborhood AP and print site survey list
TX Power : You can adjust the output power of the system to get the appropriate coverage for
your wireless network. Specify digit numbers between level 1to level 9 (the unit is %) for your
environment. If you are not sure which setting to choose, then keep the default setting level 9
(100%).
HT Physical Mode

HT TxStream/RxStream : By default, it's 2
Channel Bandwidth : The "20/40” MHz option is usually best. The other option is
available for special circumstances.
Extension Channel : Only for Channel Bandwidth “40” MHz. Select the desired channel
bonding for control.
MCS : This parameter represents transmission rate. By default (Auto) the fastest possible
transmission rate will be selected. You have the option of selecting the speed if
necessary.
Shout GI : Short Guard Interval, by default, it's “Enable”. it's can increase throughput.
However, it can also increase error rate in some installations, due to increased sensitivity
to radio-frequency reflections. Select the option that works best for your installation.
Aggregation : By default, it's “Enable”. Select “Disable” to deactivate Aggregation.
A part of the 802.11n standard (or draft-standard). It allows sending multiple frames per
single access to the medium by combining frames together into one larger frame. It
creates the larger frame by combining smaller frames with the same physical source and
destination end points and traffic class (i.e. QoS) into one large frame with a common
MAC header.
Aggregation Frames : The Aggregation Frames is in the range of 2~64, default is 32. It
determines the number of frames combined on the new larger frame.
Aggregation Size : The Aggregation Size is in the range of 1024~65535, default is
50000. It determines the size (in Bytes) of the larger frame.
Change these settings as described here and click Save button to save your changes. Click
Reboot button to activate your changes. The items in this page is for AP's RF general settings
and will be applied to all VAPs and WDS Link.

2.5 Configure Wireless Advanced Setup
The administrator can change the Slot Time, ACK Timeout, RTS threshold and fragmentation
threshold settings for the system. Please click on Wireless -> Advanced Setup and follow the
below setting.
Slot Time : Slot time is in the range of 9~1489 and set in unit of microsecond. The
default value is 9microsecond.
Slot time is the amount of time a device waits after a collision before retransmitting a
packet. Reducing the slot time decreases the overall back-off, which increases
throughput. Back-off, which is a multiple of the slot time, is the random length of time a
station waits before sending a packet on the LAN. For a sender and receiver own right of
the channel the shorter slot time help manage shorter wait time to re-transmit from

collision because of hidden wireless clients or other causes. When collision sources can
be removed sooner and other senders attempting to send are listening the
channel(CSMA/CA) the owner of the channel should continue ownership and finish their
transmission and release the channel. Then, following ownership of the channel will be
sooner for the new pair due to shorter slot time. However, when long duration of existing
collision sources and shorter slot time exist the owners might experience subsequent
collisions. When adjustment to longer slot time can’t improve performance then RTS/CTS
could supplement and help improve performance.
ACK Timeout : ACK timeout is in the range of 1~372 and set in unit of microsecond.
The default value is 64 microsecond.
All data transmission in 802.11b/g request an “Acknowledgement” (ACK) send by
receiving radio. The transmitter will resend the original packet if correspondent ACK failed
to arrive within specific time interval, also refer to as “ACK Timeout”.
ACK Timeout is adjustable due to the fact that distance between two radio links may vary
in different deployment. ACK Timeout makes significant influence in performance of long
distance radio link. If ACK Timeout is set too short, transmitter will start to “Resend”
packet before ACK is received, and throughput become low due to excessively high
re-transmission.
ACK Timeout is best determined by distance between the radios, data rate of average
environment. The Timeout value is calculated based on round-trip time of packet with a
little tolerance, So, if experiencing re-transmissions or poor performance the ACK
Timeout could be made longer to accommodate.
Slot Time and ACK Timeout settings are for long distance links. It is important
to tweak settings to achieve the optimal result based on requirement.
Beacon Interval : Beacon Interval is in the range of 40~3500 and set in unit of
millisecond. The default value is 100 msec.
Access Point (AP) in IEEE 802.11 will send out a special approximated 50-byte frame,
called “Beacon”. Beacon is broadcast to all the stations, provides the basic information of
AP such as SSID, channel, encryption keys, signal strength, time stamp, support data
rate.
All the radio stations received beacon recognizes the existence of such AP, and may
proceed next actions if the information from AP matches the requirement. Beacon is sent
on a periodic basis, the time interval can be adjusted.
By increasing the beacon interval, you can reduce the number of beacons and associated

overhead, but that will likely delay the association and roaming process because stations
scanning for available access points may miss the beacons. You can decrease the
beacon interval, which increases the rate of beacons. This will make the association and
roaming process very responsive; however, the network will incur additional overhead
and throughput will go down.
DTIM Interval : The DTIM interval is in the range of 1~255. The default is 1.
DTIM is defined as Delivery Traffic Indication Message. It is used to notify the wireless
stations, which support power saving mode, when to wake up to receive multicast frame.
DTIM is necessary and critical in wireless environment as a mechanism to fulfill
power-saving synchronization.
A DTIM interval is a count of the number of beacon frames that must occur before the
access point sends the buffered multicast frames. For instance, if DTIM Interval is set to
3, then the Wi-Fi clients will expect to receive a multicast frame after receiving three
Beacon frame. The higher DTIM interval will help power saving and possibly decrease
wireless throughput in multicast applications.
RTS Threshold : TRTS Threshold is in the range of 1~2347 byte. The default is 2347
byte.
The main purpose of enabling RTS by changing RTS threshold is to reduce possible
collisions due to hidden wireless clients. RTS in AP will be enabled automatically if the
packet size is larger than the Threshold value. By default, RTS is disabled in a normal
environment supports non-jumbo frames.
Short Preamble : By default, it’s “Enable”. To “Disable”is to use Long 128-bit Preamble
Synchronization field.
The preamble is used to signal "here is a train of data coming" to the receiver. The short
preamble provides 72-bit Synchronization field to improve WLAN transmission efficiency
with less overhead.
IGMP Snooping : the process of listening to Internet Group Management Protocol (IGMP)
network traffic. The feature allows a network switch to listen in on the IGMP conversation
between hosts and routers. By listening to these conversations the switch maintains a
map of which links need which IP multicast streams. Multicasts may be filtered from the
links which do not need them and thus controls which ports receive specific multicast
traffic.

Greenfield : In wireless WLAN technology, greenfield mode is a feature of major
components of the 802.11n specification. The greenfield mode feature is designed to
improve efficiency by eliminating support for 802.11b/g devices in an all draft-n network.
In greenfield mode the network can be set to ignore all earlier standards.
WMM QoS : This affects traffic flowing from the access point to the client station.
Configuring QoS options consists of setting parameters on existing queues for different
types of wireless traffic. You can configure different minimum and maximum wait times
for the transmission of packets in each queue based on the requirements of the media
being sent. Queues automatically provide minimum transmission delay for Voice, Video,
multimedia, and mission critical applications, and rely on best-effort parameters for
traditional IP data.
As an Example, time-sensitive Voice & Video, and multimedia are given effectively higher
priority for transmission (lower wait times for channel access), while other applications
and traditional IP data which are less time-sensitive but often more data-intensive are
expected to tolerate longer wait times.
AC Type：
Queue
AC_BK
Background
Low
High throughput. Bulk data that requires maximum
throughput and is not time-sensitive is sent to this
queue (FTP data, for example).

AC_BE
Best Effort
Medium
Medium throughput and delay. Most traditional IP
data is sent to this queue.
AC_VI
Video
High
Minimum delay. Time-sensitive video data is
automatically sent to this queue.
AC_VO
Voice
High
Time-sensitive data like VoIP and streaming media
are automatically sent to this queue.
CWmin：Minimum Contention Window. This parameter is input to the algorithm that
determines the initial random backoff wait time ("window") for retry of a transmission.
The value specified here in the Minimum Contention Window is the upper limit (in
milliseconds) of a range from which the initial random backoff wait time is
determined.。
CWmax：Maximum Contention Window. The value specified here in the Maximum
Contention Window is the upper limit (in milliseconds) for the doubling of the random
backoff value. This doubling continues until either the data frame is sent or the
Maximum Contention Window size is reached. Once the Maximum Contention
Window size is reached, retries will continue until a maximum number of retries
allowed is reached. Valid values for the "cwmax" are 1, 3, 7, 15, 31, 63, 127, 255,
511, or 1024. The value for "cwmax" must be higher than the value for "cwmin".。
AIFS：The Arbitration Inter-Frame Spacing Number specifies a wait time (in
milliseconds) for data frames。
TxOP Limit：Transmission Opportunity is an interval of time when a WME AP has
the right to initiate transmissions onto the wireless medium (WM). This value
specifies (in milliseconds) the Transmission Opportunity (TXOP) for AP; that is, the
interval of time when the WMM AP has the right to initiate transmissions on the
wireless network.。
ACM bit：Admission Control Mandatory, ACM only takes effect on AC_VI and
AC_VO. When you do not click Checkbox, it means that the ACM is controlled by the

connecting AP. If you click Checkbox, it means that the Client is in charge。
No ACK policy bit：Acknowledgment Policy, WMM defines two ACK policies:
Normal ACK and No ACK. Click “Checkbox” indicates “No ACK”
When the no acknowledgement (No ACK) policy is used, the recipient does not
acknowledge received packets during wireless packet exchange. This policy is
suitable in the environment where communication quality is fine and interference is
weak. While the No ACK policy helps improve transmission efficiency, it can cause
increased packet loss when communication quality deteriorates. This is because
when this policy is used, a sender does not retransmit packets that have not been
received by the recipient.
When the Normal ACK policy is used, the recipient acknowledges each received
uncast packet.。
Antenna: OW-300N2-A2 utilizes 2 built-In 10dBi Directional antenna and also supports 2
N-type antenna connections. Administrator can enter the software UI and select either built-in
directional antennas or N-Type external antenna. Internal and external antennas cannot be
used simultaneously. By default, OW-300N2-A2 is set to built-in directional antennas.
2.6 Create Virtual AP –Virtual AP Setup
The administrator can create Virtual AP via this page. Please click on Wireless -> Virtual AP
Setup and follow the below setting.

VAP: Display number of system's Virtual AP.
MAC Address: The MAC address of the VAP Interface is displayed here. When you
enable AP and reboot system, the MAC address will display here
ESSID: Display Virtual AP's ESSID; default is AP00~AP07.
Status: Display VAP status; default VAP0 is always on and only VAP0 can support WPS
function.
Security Type: Display Virtual AP's Security Type; default is disabled.
MAC Filter Setup: Click “Setup” button for configuring Virtual AP's Access Control List.
VAP Edit: Click “Edit” button for configuring Virtual AP's settings and security type.
Change these settings as described here and click Save button to save your changes. Click
Reboot button to activate your changes
2.7 Virtual AP General Configuration
For each Virtual AP, administrators can configure general settings and security type. Click
Wireless -> Virtual AP Setup, click “Edit” of Virtual AP List and then Virtual AP Configuration
page appears.