Cerio OW-400-A2 User manual

V1.0a
CERIO Corporation
OW-400-A2
eXtreme Power AC1200 2.4GHz / 5GHz 2x2 +17dBi
+Heater Outdoor Bridge/AP ( 800mW )
Quick Start Guide
(QSG)

V1.0a
1. Product Appearance and size.................................................................................................. 3
2. Product bottom of description................................................................................................. 4
3. Product positive/back of description..................................................................................... 5
4. Product top of description........................................................................................................ 5
5. Product setup............................................................................................................................... 6
5.1 Setup waterproof connector for RJ-45...................................................................... 6
5.2 Multifunctional Bracket for Pole/Wall Mount Installation..................................... 6
6. Set windows OS network .......................................................................................................... 8
7. Login web management by OW-400-A2 .............................................................................. 11

V1.0a
1.Product Appearance and size
Flank
Bottom
Top

V1.0a
2.Product bottom of description
(1) Ethernet 1 (RJ-45) connect port, PoE in and reset button
(2) Ethernet 2 (RJ-45) connect port, Support PoE Bridge。
(3) LED information
(4) Waterproof external N-Type connect for 5G
1
2 3
4
Heater LED
2.4Gsignal LED
Ethernet 2 LED
Ethernet 1 LED
Power LED
Reset button
5G signal LED

V1.0a
3.Product positive/back of description
* Vents keep the worst from happening. They allow enclosures and containers to breathe, equalizing
pressure and reducing condensation while filtering out liquids and other contaminants. The result:
greater product performance, increased durability, higher reliability and peace of mind.
4.Product top of description
Built-in 17dBi directional panel antenna
Front
Back
1 2
1. Ground connection
2. Wall/Pole Mounting
Bracket connect
3. Automatically adjustable
Vent design
3
Top
Waterproof external N-Type connect for 2.4G

V1.0a
5.Product setup
5.1 Setup waterproof connector for RJ-45
1) Open the Shuttered for Ethernet Port
5.2 Multifunctional Bracket for Pole/Wall Mount Installation
CERIO’s OW-400-A2’s supports both Pole and Wall Mounting. Using the provided mounting
bracket, users can deploy OW-400-A2 in a wide range of outdoor environments.
2) Lock waterproof connect for Ethernet Port
3) Install waterproof cork of RJ-45 cable
dedicated 4) Will RJ-45 connection to Ethernet port
and locking waterproof cork

V1.0a
Instructions: Use the provided screws to
secure the mounting bracket on the back of
OW-400-A2. The bracket can be attached two
different ways.
Wall Mounting
Instructions: Use the provided screws and wall
anchors to wall mount OW-400-A2. Plastic wall anchors
are always recommended to safely support the device’s
weight.
Vertical Mounting Bracket Setup Horizontal Mounting Bracket Setup

V1.0a
6.Set windows OS network
Example of Segment: (Windows 7)
IP Segment Set-up for Administrator's PC/NB
Set the IP segment of the administrator's computer to be in the same range as OW-400-A2 for
accessing the system. Do not duplicate the IPAddress used here with IP Address of OW-400-A2 or
any other device within the network.
Step 1 :
Please click on the computer icon in the bottom right window, and click “Open Network and
Sharing Center”
Step 2 :
In the Network and Sharing Center page, Please click on the left side of “Change adapter setting”
button

V1.0a
Step 3 :
In “Change adapter setting” Page. Please find Local LAN and Click the right button on the
mouse and Click “Properties”
Step 4 :
In “Properties” page, please Click “Properties” button to TCP/IP setting

V1.0a
Step 5 :
In Properties page to setting IP address, please find “Internet Protocol Version 4 (TCP/IPv4)”
and double click or click “Install”button.
Step 6 :
Select “Use the following IP address”, and fix in IP Address : 192.168.2.#
ex. The # is any number by 1 to 253
Subnet mask : 255.255.255.0
And Click "OK" to complete the fixed computer IP setting
Double click
Or click Install button

V1.0a
7.Login web management by OW-400-A2
Launch as web browser to access the web management interface of system by entering
the default IPAddress, http://192.168.2.254, in the URL field, and then press Enter.
Browser will pop up "login" page. Please key in username and password into the system
on OW-400-A2.
The system manager Login Page then appears.
Enter “root” as User name and “default” as Password, and then click “OK” to login to
the system.
Login information
Please base your Software version check to OW-400-A2 CenOS5.0 User’s Manual
By CenOS5.0 Software Router / AP / WDS/Client Bridge + RepeaterAP/ WISP+
Repeater AP mode
Default IPAddress 192.168.2.254
Account
root
Password
default