Challenger Lifts EnviroLift EV1020QC Instruction manual

Rev. 8/25/20
EVQC-IOM-A.doc
MODEL EV1020QC Quick Cycle
(10,000 LB CAPACITY – 2500 LB PER ARM)
INSTALLATION,OPERATION &MAINTENANCE MANUAL
Two Post, Inground, Cassette EnviroLift™
2311 South Park Rd. Louisville, Kentucky 40219
Email:[email protected]Web site:www.challengerlifts.com
Office 800-648-5438 / 502-625-0700 Fax [phone]
IMPORTANT: READ THIS MANUAL COMPLETELY BEFORE
INSTALLING or OPERATING LIFT

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
2
General Specifications
EV1020QC
ARise Height (Screw Pads Highest Position) 74”
BOverall Width 110 1/4”
CDrive Thru 83 1/2”
DArm/Pad Reach (min/max) 19 5/8” Min / 42 1/8” Max
EOverall Length (min/max) NA
Screw Pad Height 4-1/8” Min. / 6-3/8” Max.
*Lifting Capacity
(Hydraulic Pressure at Cap.)
10,000 lbs
(2550 psi)
Max Load Per Arm 2,500 lbs
** Lifting Time 24 Sec. (approximate)
Motor
3HP, 208/230 Volt,
Single Phase, 60 Hz
* Lift capacity ratings are based on loads equally distributed on all four arms.
** Lifting and lowering speeds may vary depending on the type, viscosity and
temperature of the oil as well as vehicle weight.
EV1020QC

Rev. 8/25/20
EVQC-IOM-A.doc
VERTICAL CLEARANCE
Check the height of the area where the lift is to be
installed. Clearance should be calculated based on
the full raised height of the lift.
Failure by purchaser to
provide adequate
clearance could result in
unsatisfactory lift performance, property
damage, or personal injury.
LOCATION
This lift has been evaluated for indoor use only
with an operating ambient temp. range of 5 –
40°C (41– 104°F)
ELECTRICAL REQUIREMENTS
For lift installation and operation it is necessary
to have a dedicated circuit with circuit breaker or
time delay fuse. Refer to wiring diagram for
circuit sizing.
FLOORING
A qualified person should be consulted to
address seismic loads and other local or state
requirements.
SAFETY NOTICES AND DECALS
For your safety, and the safety of others, read and
understand all of the safety notices and decals
included here.
READ ENTIRE MANUAL BEFORE
ASSEMBLING,INSTALLING,
OPERATING,OR SERVICING THIS
EQUIPMENT.
PROPER MAINTENANCE AND
INSPECTION IS NECESSARY FOR SAFE
OPERATION.
DO NOT OPERATE A DAMAGED LIFT.
Safety decals similar to those shown here are
found on a properly installed lift. Be sure that all
safety decals have been correctly installed on the
Power Unit reservoir. Verify that all authorized
operators know the location of these decals and
fully understand their meaning. Replace worn,
faded, or damaged decals promptly.
Do not attempt to raise a
vehicle on the lift until the
lift has been correctly
installed and adjusted as described in this
manual.
WARNING
WARNING

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
4
WARNING:
DO NOT permit personnel to operate lifts who are not familiar with the
information contained in these instructions.
Safety devices and controls are provided for your protection. DO NOT alter any
devices to serve a special purpose. Never interfere with safety features built into
the controls or the lift lock. DO NOT block valves open.
Study these instructions carefully to become familiar with the general installation
procedure. Before installing your Challenger EnviroLift™, inspect the lift to insure that it
is complete and undamaged. If it is apparent that the lift has been mishandled in
shipment, or if parts or assemblies are missing, note the damage or missing part(s) on
the shipping papers and notify Challenger Lifts, Inc. immediately.
The Challenger 2-Post EnviroLift™ consists of two packages, the lift-containment assy.
and an accessory package. This accessory package includes the superstructures,
arms, power unit and hardware box.
In addition to the components furnished with the lift, certain tools, equipment, supplies
and materials are required. The installer or purchaser of the lift must furnish these
items:
TOOLS &SUPPLIES
(MINIMUM REQUIRED)
Forklift, cherry picker, crane, winch truck, chain falls, winches, or hoist to unload
and erect lift
Machinist level, or four-foot carpenters level to check cylinder plumb
Drywall Square, chalk line, or transit for bay layout
Wiring, conduit, wiring devices for electrical power supply, Shop Air supply with
filter lubricator
Hand tools for lift assembly
6” x 6” wood beam (length will vary based on soil conditions and pit width)
Quantity 4 of each: 1/2-13 x 18” lg all thread rods, 1/2 Washers, and 1/2-13 nuts.
2" sch. 40 PVC for air / hyd. chase
12 Qtz 10wt Dexron III ATF
Hydraulic Hose (4000 psi working/16000 psi min. Burst) SAE #6 9/16-18 37°
Female Swivel Both Ends. Fittings must conform to the SAE J514 Guidelines.
This hose will connect the power unit to a fitting in the center of the tub. The
length of hose needed to run from the chase to the fitting is 50inches.
Five yards pea gravel as backfill.
Accepted Oils – Do not use oils with detergents, hydraulic fluid is not provided with the
lift shipment
-10 wt. anti-foam, anti-rust hydraulic / biodegradable oil
-Dexron III ATF

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
5
Installation Procedure
Location
Locate lift to allow plenty of working room on all sides. Allow room for workbenches at
front of bay, aisles, lubrication equipment or other obstructions. Check overhead
clearances. Ordinarily 12 feet is ample for automobiles. Observe the recommended
minimums in Fig 1.
13'-0" Min.
Nearest Obstruction
10'-0" Min.7'-0" Min.
Fig. 1
New Construction Excavation
New construction requires an excavation as shown in Fig. 2. NOTE: Concrete must be
finished to edge of concrete tie (3/16” below top of concrete ties, see Fig. 2 below). All
depths are measured from the finished floor level. Failure to comply will void the
warranty. The power unit may be installed on the nearest wall or floor pedestal. The
power unit should be located out of the working area around the lift and vehicle, but
close enough to allow good visibility while operating the lift. Hydraulic and air lines from
the lift should be recessed under the slab in a 2” sch. 40 PVC chase. CLI will supply
the proper coupling to join the PVC chase to the lift.
Concrete Tie Anchor
102 1/4"
9'-0"
8'-0" 3'-0"
Clean Pea Gravel
Back Fill
2" PVC Chase
8 1/4"
18"
135° Typ.
3/16"
Finished Floor
Fig. 2

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
6
Existing Facility Excavation
Excavation is the same as in new construction. However, it will be necessary to break
out a trench 6"-8" wide by 12" deep to run the PVC chase.
Installation
1. For best balance of lift / containment assembly while lowering into excavation,
sling using the shipping straps provided. See Fig. 3. DO NOT remove or loosen
any of the bearing assembly bolts at this time.
Note: The assembly weighs approximately 2300 lbs.
Hoist
PVC Chase Inlet
Lift /Containment Assembly
Bolts Removed For
1/2-13 x 18 All Thread
Fig. 3
2. Using a chain hoist and tripod, fork lift, crane, etc. for lifting; lower the lift /
containment assembly in the excavation being sure the PVC inlet hole is toward
the power unit, until the top of the assembly is 1/8" to 1/4" above finished floor
level and aligned with the previously determined center lines. Refer to Figures 1
and 3.
3. Remove the outer two bolts from each end of the center cover plate and replace
with ½-13 x 18 threaded rods. Attach two 6 x 6 timbers using ½-13 nuts and
washers, to support the lift / containment assembly on the existing floor or forms.
Remove the shipping straps and replace the bolts. Torque the bolts to 60 ft-lbs.
Bend concrete tie anchors out 90 degrees and down 45 degrees. Refer to
Figures 3 and 4.

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
7
Finished
Floor
1/2-13 x 18
All Thread Rod
1/2-13
Nut and Washer
6 x 6 Support
1/2-13 x 18
All Thread Rod
Lift / Containment
Assembly
Concrete Tie Anchor
1/2-13
Nut and Washer
Existing Floor New Floor
Fig. 4
4. Plumb and level using a machinist level on top of each bearing assembly. Level
in several directions. DO NOT level off the lift frame.
5. Select the power unit location so that the driver or passenger side of the vehicle
is within view. Operator should be in a position to notice any misalignment of the
vehicle during the lifting operation.Run the 2" PVC chase from the control area
and join to the lift / containment assembly using the coupling provided. Use a
soap water solution to ease assembly. All PVC joints must be leak proof. The
power unit end of the chase should be finished as shown in Fig. 5 to prevent
contamination from entering the chase, while allowing the system to breathe.
18.0" Min.
2" PVC Chase
Lock Release Valve Bracket Assy.
Power Unit
Wall Mounting Bracket
5/16-18 Hex Bolt, Washer and Nut
Fig. 5
Note: The power unit location needs to be high enough to avoid inadvertently
depressing the lowering valve handle with a tool cart, oil pan, etc.

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
8
6. Before beginning to back fill take care to protect the plunger tops, cover joints and
hardware from debris. Duct tape should be used to cover these joints. Make sure
all factory supplied thread protectors and caps are in place. Recheck plumb and
back fill approximately 2 feet with pea gravel. Recheck plumb and continue back
filling using pea gravel and rechecking plumb to within 18 inches of finished floor
level. DO NOT use a mechanical tamper or saturate the fill to achieve
compaction, hand tamp only.
7. Check plumb and elevation, adjust if necessary. DO NOT remove 6 x 6 supports
at this time.
Existing Floor / Block Out
8. If a Block Out is used or an Existing floor needs to be saw cut for excavation the
Cut Out/Block Out should be a minimum of 6' x 11' as per the figure below.
13' Min.
Nearest Obstruction
7' Min.
6' Min.
11' Min.
9. Pour concrete floor taking care not to run concrete in or on top of the lift /
containment assembly. NOTE: Concrete must be finished to edge of concrete tie
(3/16” below top of concrete ties, see Fig. 2). The floor should slope away from
the lift for drainage. The floor slope should not exceed 1/16” per foot. 3500 psi
concrete, steel reinforced per local commercial practice is required. The new
concrete must be mechanically joined to the existing floor with rebar.
10. After the concrete has set up remove the 6 x 6 supports, threaded rods, and
shipping straps. Replace the cover bolts with the ½-13 x 2” HFHB. The shipping
strap bolt replacements are supplied in the hardware box. Torque the bolts to 60
ft-lbs.
11. After the concrete has set up, remove the 6 x 6 supports and threaded rods.

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
9
Replace the cover bolts and torque to 60 ft-lbs.
12. DO NOT use the lift until the concrete has fully cured to 3500 psi.
New Floor
13. Pour 8” to 12” of concrete around the top of the lift / containment assembly and
install rebar to tie in the finished floor. Refer to Fig. 6.
6 x 6 Support
Lift / Containment
Assembly
1/2-13 x 18
All Thread Rod
1/2-13
Nut and Washer
8"-12"
Rebar
Fig. 6
14. After the concrete has set up remove the 6 x 6 supports, threaded rods, and
shipping straps. Replace the cover bolts with the ½-13 x 2” HFHB. The shipping
strap bolt replacements are supplied in the hardware box. Torque the bolts to 60
ft-lbs.
15. Pour concrete floor taking care not to run concrete in or on top of the lift /
containment assembly. The floor should slope away from the lift for drainage.
The floor slope should not accede 1/16" per foot.
16. DO NOT use the lift until the concrete has fully cured to 3500 psi.
17. Install the power unit mounting bracket or floor pedestal using the anchors
provided. IMPORTANT: The electric motor must be mounted at least 18 inches
above the finished floor level as per National Electric Code NFPA70. Assemble
the power unit and lock release valve bracket to wall mounting bracket or pedestal
with 5/16-18 cap screws and nuts provided. Refer to Fig. 5.
18. Connect the power unit to a electrical source as shown in Fig. 7 below.

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
10
2/T11/L1
3/A14/A2
LOAD
INPUT
M
(Normally Open)
FIELD CONNECTIONS
A2A1
T9
T5
T4
T6
M
T8
T3
T7
T2
T1
12
34
56
L3
L2
L1
T3
T2
T1
FACTORY WIRED FOR
208−240V
6
4
2
5
3
1
RECONNECTIONS FOR
440−480V
T3
T2
T1
T9
T6
T7
T4
T8
T5
FOR THREE PHASE
M
FOR SINGLE PHASE
Wiring Diagram
Fig. 7

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
11
19. Fill the reservoir with 12 quarts of 10 weight hydraulic / biodegradable oil or
Dexron III ATF.
20. Remove the center cover plate from the lift / containment assembly to expose the
hydraulic connection. Attach the 37 deg. Union adapter (supplied) to the hard
hydraulic line. Attach the 37 deg. Elbow adapter (supplied) to the power unit
pressure port. Fish the hydraulic hose assembly through the PVC chase starting
at the power unit end.
21. The shop air supply must be clean, dry, lubricated, and regulated to 90-120
psi. The air supply must run through a Filter/Regulator/Lubricator (FLR) within 30
feet of factory assembled air valve. Failure to provide clean, dry lubricated
and pressure regulated air will void warranty on pneumatic components.
Push ¼” airline through the PVC chase beginning at the power unit. Connect the
airline to the appropriate push lock fittings at each end. Refer to Fig. 8.
NOTE: DO NOT bypass factory supplied in-line filter.
3/8 Hose Barb (For Inlet Shop Air)
In-Line Air Filter
1/4" Push Lock Fitting
Fig. 8
22. Finish Energize the power unit to run the cylinder up about 3 feet. Loosen the
bleed screw at the top of each cylinder, and allow the trapped air to escape.
Bleed both cylinders until clear oil is seen. Refer to Fig. 9. Raise the lift to full
stroke and continue to run the power unit for another 10 seconds to check for
hydraulic leaks.
Fig. 9

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
12
23. While the lift is in up position actuate the air valve and check for proper operation
of the locking mechanism.
24. Replace the center cover plate and torque bolts to 60 ft-lbs.
25. With the plungers raised slight (1”-2”) to avoid damaging the wiper. Position the
bolster over the pistons and attach using the 7/8-9x3 1/2 cap screws and lock
washers provided and torque to 120 ft-lbs. Lightly grease each arm pin and hole
with anti-seize and install the swing arms with pins and snap rings.
26. Extend the foot pad to both extents and apply “anti-seize” to the three retaining
rings and where the double screw makes contact with the base of the foot pad.
27. With the lift lowered, arms extended fully and foot pad in the lowest position,
check clearance of the foot pad screw to ensure it does not make contact with the
floor. Use the height adjustment bolt (see figure 10) to either raise or lower the
bolster as necessary. If there is more then 3/8” of clearance on both screws with
the bolt fully seated against the bottom of the bolster remove the bolt.
Fig. 10
28. Finish installation by cleaning around the top of the lift / containment unit and
Thoroughly seal joints between the cover plate, bearing plates, and the perimeter
with a premium silicone caulk.
FEMALE ARM SHIM INSTALL (3-STAGE ARMS ONLY)
29. Extend the arm fully and lift up on the male portion, Fig 11.
30. Using a hammer to set, place the shim on the mouth of the female arm. Use the
provide self-locking set screw and 1/8” Allen head wrench to securely lock the
shim in place.
Fig. 11 – Arm Shim, 3-Stage
Lifting a Vehicle

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
13
Be sure the adapters are in the lowered position and the arms are parked as seen in
Fig. 1 before attempting to drive on or off of the lift. Failure to do so may damage the
adapters or vehicle.
Adjust the adapters laterally and fore and aft to contact points of maximum stability in
accordance with the vehicle manufacturer’s recommended lifting points.
Remember that positioning the adapters to yield the widest and longest distances
between points of contact with the vehicle lifting points provides the maximum
stability.
Adapters may be used in lowered, intermediate or raised height positions as necessary
to clear mufflers, pipes, brake lines etc. To obtain maximum stability when adapters are
used at maximum height position, front and rear adapters should be rotated to oppose
each other.
When Lifting Framed vehicles it is required that you use the Frame Engaging
Adapters ((10318) Optional). Failure to do so on slick (undercoated) and or
pitched frame rails may result in personal or property damage.
To raise depress the run switch on the power unit and hold until the vehicles tires just
clear the floor. STOP and check adapters for proper contact of vehicle manufacturers
recommended lifting points and stability of the vehicle. Continue to raise the vehicle to
a few inches above the desired working height. Lower the lift by depressing the
lowering valve handle until the lock is engaged. DO NOT go under vehicle unless lock
is engaged and all four adapters are securely contacting the vehicle manufacturers
recommended lifting points.
Lowering a Vehicle
To lower, raise lift slightly and disengage lock by depressing lock release palm button.
Continue to hold lock release palm button and depress the lowering valve handle until
the lift is completely lowered. Return adapters to there lowest position and park the
swing arms to provide unobstructed exit of the vehicle.
Loss of Power
If for any reason the lift will not raise off the locks or the locks will not retract, consult factory
authorized personnel.
DO NOT OVERRIDE ANY SAFETY FEATURE IN AN ATTEMPT TO LOWER THE LIFT.
Trouble Shooting
If any problems are encountered please contact your local Challenger Representative.

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
14
OWNER/OPERATOR CHECKLIST
31. Demonstrate the operation of the lift to the
owner/operator and review correct and safe lifting
procedures using the Lifting It Right booklet as a
guide.
32. Return all provided literature (including this
manual) to the literature pack envelope and
deliver the envelope to the
owner/operator/employer
33. Complete the online warranty registration (refer to
the included warranty statement).
OPERATION PROCEDURE
SAFETY NOTICES AND DECALS
This product is furnished with graphic safety warning
labels, which are reproduced on page 3 of these
instructions. Do not remove or deface these warning
labels, or allow them to be removed or defaced. For
your safety, and the safety of others, read and
understand all of the safety notices and decals
included.
OWNER/EMPLOYER RESPONSIBILITIES
This lift has been designed and constructed according to
ANSI/ALI ALCTV-2017 standard. The standard applies to lift
manufactures, as well as to owners and employers. The
owner/employer’s responsibilities as prescribed by ANSI/ALI
ALOIM-2008, are summarized below. For exact wording refer
to the actual standard provided with this manual in the literature
pack.
The Owner/Employer shall insure that lift operators are
qualified and that they are trained in the safe use and
operation of the lift using the manufacturer’s operating
instructions; ALI/SM 93 -1, ALI Lifting it Right safety
manual; ALI/ST-90 ALI Safety Tips card; ANSI/ALI ALOIM-
2008, American National Standard for Automotive Lifts-
Safety Requirements for Operation, Inspection and
Maintenance; ALI/WL Series, ALI Uniform Warning Label
Decals/Placards; and in case of frame engaging lifts,
ALI/LP-GUIDE, Vehicle Lifting Points/Quick Reference
Guide for Frame Engaging Lifts.
The Owner/Employer shall establish procedures to
periodically inspect the lift in accordance with the lift
manufacturer’s instructions or ANSI/ALI ALOIM-2008,
American National Standard for Automotive Lifts-Safety
Requirements for Operation, Inspection and Maintenance;
and the employer shall insure that the lift inspectors are
qualified and that they are adequately trained in the
inspection of the lift.
The Owner/Employer shall establish procedures to
periodically maintain the lift in accordance with the lift
manufacturer’s instructions or ANSI/ALIOIM-2008,
American National Standard for Automotive Lifts-Safety
Requirements for Operation, Inspection and Maintenance;
and the employer shall insure that the lift maintenance
personnel are qualified and that they are adequately
trained in the maintenance of the lift.
The Owner/Employer shall maintain the periodic
inspection and maintenance records recommended
by the manufacturer or ANSI/ALI ALOIM-2008,
American National Standard for Automotive Lifts-
Safety Requirements for Operation, Inspection and
Maintenance.
The Owner/Employer shall display the lift
manufacturer’s operating instructions; ALI/SM 93 -
1, ALI Lifting it Right safety manual; ALI/ST-90 ALI
Safety Tips card; ANSI/ALI ALOIM-2008, American
National Standard for Automotive Lifts-Safety
Requirements for Operation, Inspection and
Maintenance; and in the case of frame engaging lift,
ALI/LP-GUIDE, Vehicle Lifting Points/Quick
Reference Guide for Frame Engaging Lifts; in a
conspicuous location in the lift area convenient to
the operator.
IMPORTANT SAFETY INSTRUCTIONS
When using your garage equipment, basic safety
precautions should always be followed, including
the following:
1. Read all instructions.
2. Care must be taken as burns can occur from
touching hot parts.
3. To reduce the risk of fire, do not operate
equipment in the vicinity of open containers of
flammable liquids (gasoline).
4. Keep hair, loose clothing, fingers, and all parts
of body away from moving parts.
5. Use only as described in this manual. Use only
manufacturer’s recommended attachments.
6. ALWAYS WEAR SAFETY GLASSES.
Everyday eyeglasses only have impact
resistant lenses, they are not safety glasses.
SAVE THESE INSTRUCTIONS

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
15
Maintenance
To avoid personal injury, permit only qualified personnel to perform maintenance on this equipment. Maintenance
personnel should follow lockout/tagout instructions per ANSI Z244.1.
The following maintenance points are suggested as the basis of a routine maintenance program. The actual maintenance
program should be tailored to the usage of the lift. See ANSI/ALI ALOIM booklet for periodic inspection checklist and
maintenance log sheet.
If lift stops short of full rise or chatters, check fluid level and bleed both cylinders per Installation Instructions.
Replace all Safety, Warning or Caution Labels if missing or damaged (See Installation instructions page 3.)
Daily
Drain water from air supply to avoid contamination of lock release components.
Check lock operation. The lock operation should be heard as lift is raised.
Inspect lifting adapters for damage.
Keep area around lift / containment assembly clean and free of dirt, sand, water, etc. to
prevent scoring of the plunger.
Remove excess grease and debris from plunger by wiping them down with a clean cloth.
Monthly
Check fluid level in the power unit.
Check for proper torque on all superstructure bolts (120 ft-lbs.).
Clean and lubricate lifting arm pins and pads.
Quarterly
Grease Lift Guide bearings using Mobil, Mobilith SHC 1500 synthetic grease. Each guide
bearing is supplied with two grease zerk and should take 10-12 pumps (hand pump only) while
raising and lowering the lift empty.

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
16
Parts Break Down
Model EV1020QC
IMPORTANT
Replace all worn, damaged, or broken parts with parts approved by Challenger Lifts Inc.
or with parts meeting Challenger Lifts Inc. specifications.
Contact your local Challenger Lifts Parts Distributor for pricing and availability.
(Call Challenger Lifts Inc. [phone] for the Parts Distributor in your area)

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
17
EV1020QC Super Structure
Item Part Qty. / Lift Description
1 B2270 4
Foot Pad Assembly (items 1A-1F)
1A A1104-H 4
Rubber Insert
1B A1101-1H 4
Foot Pad Weld
1C B17256 4
2 x 30mm Retaining Ring
1D B17257 8
3 x 45mm Retaining Ring
1E B2261 4
Threaded Sleeve
1F B17276-1 4
Threaded insert
2 B2211 4
Roll Pin, 6mm DIA x 30mm Lg.
7 B2218C 4 Male Arm Weld
8 B2202-02 4
Roll Pin, Ø12mm x 80mm Lg.
9 CS1020010200C 2 Intermediate Arm Weld Left
CS1020020200C Intermediate Arm Weld Right
10 CS1020010100B 2 Female Arm Weld Left
CS1020020100B Female Arm Weld Right
11 16125 4
1 7/8 Snap Ring
12 B17259 4
Arm Pin
13 B17001EV 2
Bolster
14 B17250SLD 2 3-Stage Arm Assembly Left
B17250SRD 3-Stage Arm Assembly Right
15 16473 12
7/8-9 x 3-1/2” Hex Head Cap Screw
16 16160 2
Finishing Plug
17 16154 12
7/8 External Tooth Lock Washer
18 17314 2
M12 x1.75 x 20mm Lg. Hex Head Cap Screw, Gr. 8.8 Zinc Plated
19 B2202-01 4
Roll Pin, 12mm Dia x 60mm Lg.
20 17425 4
Female Arm Shim, 3-Stage
21 17426 4
¼-20 x ¼” Lg. Self Lock Set Screw
22 CS1020-04 4
Stop Block
23 17350 8
8mm x 10mm Lg. Flat Head Bolt
24 CS1020-05 4
Stop Loop

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
18
Containment
1
1
1
1
Item Part Qty./Lift Description
1 17200 1 Single Piece Rubber Gasket
2 17380 1 Containment Tub (Not Serviceable after Installation)
3 15009 1 2" PVC Grommet (Not Serviceable after Installation)
4 17321 2 Concrete Tie Weld-Short (Not Serviceable after Installation)
5 17320 2 Concrete Tie Weld-Long (Not Serviceable after Installation)

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
19
2
3
5
2
8
Bearings
Item Part Qty / Lift Description
1 17152 22 ½-13 x 2” lg Hex Flange Head Bolt
2 16485EV 4 Wiper
3 16486EV 4 Bearing
4 VS5096 2 1/8 NPT Grease Fitting
5 B17212 2 Bearing Weld
6 16132 12 ¼” x 12” lg Grease Line
7 17410 4 ¼” Push Lock Cross
8 16129 12 1/8 NPT x ¼” Push Lock Elbow
9 16429 1 Cover Plate
10 17205 2 Bearing Assembly
11 16163 4 Male Connector 1/4 Tube x 1/8 NPT
12 17411 4 ¼” x 2” Grease Line

Models EV1020QC
Installation, Operation and Maintenance
Rev. 8/25/20
EVQC-IOM-A.doc
20
Frame
8
8
8
8
9
9
9
9
11
11
11
11
10
10
10
10
12
12
12
12
2
2
2
23
3
3
3
3
3
3
3
1
1
1
12 2
2
2
1
1
1
12 2
2
23
3
3
3
4
13
14
56
7
4
13
14
56
7
4
13
14
56
7
4
13
14
56
7
15 16 17
15 16 17
15 16 17
15 16 17
15 16 17
15 16 17
15 16 17
15 16 17