Chamberlain MIRACLE-ONE User manual

UL Listings and Instructions 2-5
Role of Specifiers and Designers 6
Role of Dealers, Installers and Trained Gate System Technicians 6
Role of End Users / Home Owners 7
Swing Gate Systems 7
Warnings and Precautions 8
“Open to the Inside” Mounting Specifications 9
“Open to the Outside” Mounting Specifications 10
Step-by-Step Operator Mounting Instructions 11-14
Removing the Control/Surge Suppressor Boards 15
Mounting the Control Box 15
Wiring 1 Operator to the Surge Suppressor Board 16
Wiring 2 Operators (Master/Second) to the Surge Suppressor Board 17
Choosing Gate Movement Direction 18
Sensor Adjustment 18
Adjustable Timer 19
Earth Ground Rod Installation 19
Connecting Power Supply 20
Wiring Additional Inputs 21
Single Operator Loop Size and Placement 22
Master / Second Loop Size and Placement 23
Loop Installation and Number of Wire Turns 24
Loop Detector Wiring 25
Photocell Installation 26
Single Control Board Description 27
Master / Second Control Board Description 28
Surge Suppressor Board Description 29
Alarm / Maglock Control Board Connections 30
UL Audio Alarm 31
Burglar Alarm and Proximity Switch 31
“Gate Opening Inside ” Installation of Maglock / Solenoid Relay 32
“Gate Opening Outside ” Installation of Maglock / Solenoid Relay 33
Close Delay Option (Master / Second Only) 34-35
Emergency Key Release 36
Troubleshooting 37-39
Optional Solar Power 40
Miracle 1 Accessories 41
Miracle 1 Parts Illustration 42
Miracle 1 Parts List / Maintenance 43
Features and Specifications 45
Quick Reference Surge Suppressor Wiring Diagram 46-47
Please DO NOT
Touch me!...
Unless you are an
Authorized Service
Technician!
TABLE OF CONTENTSTABLE OF CONTENTST A B L E O F C O N T E N T S
© 1998-2004 by Chamberlain Professional Products
Release 4
01/04
All rights reserved. No part of this manual may be
reproduced in any means without the expressed written
permission of the publisher. Materials, components and
specifications are subject to change without notice.
Attention: This handbook is exclusively for qualified installation personnel, and assistance and/or maintenance
service.
- The performances indicated in this handbook are valid only if a correct assembly has been carried out.
For Toll Free Technical Support: 1-888-ELITE-10
1

ETL LISTINGS AND INSTRUCTIONSETL LISTINGS AND INSTRUCTIONSE T L L I S T I N G S A N D I N S T R U C T I O N S
Install the gate operatoronly when:
The operatorisappropriate forthe constructionand the usage class of the gate.
All exposed pinch pointsare eliminated orguarded, and
Guarding issupplied forexposed rollers.
The operatorisintended forinstallationonly ongatesused forvehicles. Pedestrians must be
supplied with a separate access opening.
The gate must be installed ina locationso that enough clearance issupplied betweenthe gate
and adjacent structureswhenopening and closing to reduce the risk of entrapment. Swinging
gatesshall not openinto public access areas.
The gate must be properly installed and work freely inboth directions priorto the installationof
the gate operator.
Controlsmust be farenough from the gate so that the userisprevented from coming incontact
with the gate while operating the controls. Controlsintended to be used to reset anoperatorafter
2 sequential activations of the entrapment protectiondevice ordevicesmust be located inthe line
of sight of the gate outdoor. Easily accessible controlsshall have a security feature to prevent
unauthorized use.
All warning signs and placardsmust be installed where visible inthe area of the gate. A minimum
of two placardsshall be installed. A placard isto be installed inthe area of each side of the gate
and be visible to personlocated onthe side of the gate onwhich the placard isinstalled.
A)
B)
C)
D)
E)
F)
Installation Instructions Regarding the Gate Operator
1.
2.
3.
2

ETL LISTINGS AND INSTRUCTIONSETL LISTINGS AND INSTRUCTIONSE T L L I S T I N G S A N D I N S T R U C T I O N S
Fora gate operatorutilizing a non-contact sensorsuch asa photo beam:
See instructions onthe placement of non-contact sensorforeach type of application.
Care shall be exercised to reduce the risk of nuisance tripping, such aswhena vehicle
tripsthe sensorwhile the gate isstill moving.
One ormore non-contact sensors shall be located where the risk of entrapment or
obstructionexists, such asthe perimeterreachable by a moving gate orbarrier.
A hard wired contact sensorshall be located and itswiring arranged so that the
communicationbetweenthe sensorand the gate operatorisnot subjected to mechanical
damage.
A wireless contact sensorsuch asthe one that transmitsradio frequency (RF) signalsto
the gate operatorforentrapment protectionfunctions shall be located where the
transmissionof the signalsare not obstructed orimpeded by building structures, natural
landscaping orsimilarobstruction. A wireless contact sensorshall functionunderthe
intended end-use conditions.
One ormore contact sensors shall be located onthe inside and outside leading edge of a
swing gate. Additionally, if the bottom edge of a swing gate isgreaterthan6 inches(152
mm) above the ground at any point initsarc of travel, one ormore contact sensors shall
be located onthe bottom edge.
Fora gate operatorutilizing a contact sensorsuch asanedge sensor:
G)
H)
1.
2.
3.
1.
2.
3.
3

ETL LISTINGS AND INSTRUCTIONSETL LISTINGS AND INSTRUCTIONSE T L L I S T I N G S A N D I N S T R U C T I O N S
READ AND FOLLOW ALL INSTRUCTIONS.
Neverlet childrenoperate orplay with gate controls. Keep the remote control away from
children.
Alwayskeep people and objectsaway from the gate.
NO ONE SHOULD CROSS THE PATH OF A MOVING GATE!
Test the gate operatormonthly. The gate MUST reverse oncontact with a rigid object or
stop whenanobject activatesthe non-contact sensors. Afteradjusting the force orthe
limit of travel, retest the gate operator. Failure to adjust and retest the gate operator
properly canincrease the risk of injury ordeath.
Use the emergency release only whenthe gate isnot moving. Make sure the powerfor
the gate operatorisoff.
KEEP GATES PROPERLY MAINTAINED. Read the manual. Have a qualified service
personmake repairs to the gate orgate hardware.
The entrance isforvehiclesonly. Pedestrians must use separate entrance.
SAVE THESE INSTRUCTIONS.
1.
2.
3.
4.
5.
6.
7.
8.
Important Safety Instructions
Warning - To reduce the risk of injury or death:
4

ETL LISTINGS AND INSTRUCTIONSETL LISTINGS AND INSTRUCTIONSE T L L I S T I N G S A N D I N S T R U C T I O N S
Gate – A moving barriersuch asa swinging, sliding, raising lowering, rolling, orlike, barrier,
that isa stand-alone passage barrieroristhat portionof a wall orfence system that controls
entrance and/oregress by persons orvehiclesand completesthe perimeterof a defined
area.
Vehicular horizontal slide-gate operator (or system) – A vehiculargate operator(or
system) that controlsa gate which slidesina horizontal directionthat isintended foruse for
vehicularentrance orexit to a drive, parking lot, orthe like.
Residential vehicular gate operator – Class I – A vehiculargate
operator(orsystem) intended foruse ina home of one-to four
single family dwelling, ora garage orparking area associated
therewith.
Commercial/General access vehicular gate operator –
Class II – A vehiculargate operator(orsystem) intended for
use ina commercial locationorbuilding such asa
multi-family housing unit (five ormore single family units)
hotel, garages, retail store orotherbuilding servicing the
general public.
Commercial/General access vehicular gate operator –
Class III – A vehiculargate operator(orsystem) intended for
use inanindustrial locationorbuilding such asa factory or
loading dock area orotherlocations not intended to service
the general public.
Restricted access vehicular gate operator – Class IV – A
vehiculargate operator(orsystem) intended foruse ina
guarded industrial locationorbuilding such asanairport
security area orotherrestricted access locations not
servicing the general public, inwhich unauthorized access is
prevented via supervisionby security personnel.
5

6
Specifiers and designers should design an automatic vehicular gate system to:
• Incorporate UL 325 compliant equipment.
• Utilize an operator suited for gate system type, size, frequency of use, location and user population
(Refer to UL 325 for usage class definitions)
• Separate pedestrian access from vehicle access.
• Reduce or eliminate pinch points.
• Reduce risk of entrapment injuries by minimizing all gaps in the gate and enclosing the area of the
travel of the gate.
• Secure controls from unauthorized use.
• Locate all controls out of reach from the gate.
• Allow the user full view of the gate when operating.
• Consider special populations, such as children or the elderly.
• Conspicuously display all warnings and instructions.
• Be consistent with DASMA’s Automatic Gate Opener System Safety Guide.
ROLE OF SPECIFIERS AND DESIGNERS
Installers, during the course of the installation proceedings for each job, should:
• Confirm that the gate operator being installed is appropriate for the application.
• Confirm that the gate is designed and built according to current published industry standards.
• Confirm that all appropriate features and accessory devices are being incorporated, including both
primary and secondary entrapment protection devices.
• Make sure that the gate works freely before installing the operator.
• Repair or service worn or damaged gate hardware before installing the operator.
• Eliminate all gaps in the sliding gate below a 4 foot height that permit a 2 1/4 inch sphere to pass
through any location, including the area of the adjacent fence covered when the gate is in the open
position.
• Install the gate operator according to the manufacturer’s installation instructions.
• Adjust the operator clutch or load-sensing device to the minimum force setting that allows reliable gate
operation.
• Install operator inside fence line (DO NOT install operator on public side of fence line)
• Install a proper electrical ground to a gate operator.
• Install keypad controls where users cannot touch, or reach through gate while operating controls.
• Install controls where user has full view of gate operation.
• Install all warning signs (In accordance with UL 325) on both sides of the gate to warn persons in the
area of potential hazards associated with automatic vehicular gate operation.
• Test all features for proper functions before placing the automatic vehicular gate into service.
• Demonstrate the basic functions and safety features of the gate system to owners/end users/general
contractors, including how to turn off power and how to operate the manual disconnect feature.
• Leave safety instructions, product literature, installation manual and maintenance manual with end
user.
• Explain to the owners the importance of a service contract that includes a routine re-testing of the
entire system including the entrapment protection devices, and explain the need for the owners to
insure that this testing is performed routinely.
• Offer the owner/end user a maintenance contract, or contact them regularly to offer maintenance.
ROLE OF DEALERS, INSTALLERS AND
TRAINED GATE SYSTEM TECHNICIANS

7
End users should be made aware that they must:
• Contact a trained gate systems technician to maintain and repair the gate system (End users should
never attempt to repair the gate)
• Retain and utilize the installation and maintenance manual and safety instructions.
• Routinely check all gate operator functions and gate movement.
• Discontinue use if safety systems operate improperly, the gate is damaged, or the gate is difficult to
move.
• Never overtighten the operator clutch of load sensing device to compensate for a damaged or stiff
operating gate.
• Prominently display and maintain warning signs on both sides of the gate.
• Keep all obstructions clear of the vicinity of the path of the gate system.
• Actively discourage pedestrian use of the vehicular gate operating system.
• Prevent anyone from playing near any part of the gate system.
• Never allow anyone to climb under, over or through a gate or the adjacent fence area.
• Never allow children to operate gate.
• Keep portable controls out of reach of children.
• Never allow anyone to install an operating control within reach of the gate.
• Never allow anyone to install a horizontal slide gate with exposed rollers or openings large enough to
allow a sphere of 2 1/4 inches to pass through any portion of the gate below a 4 foot height, including
the area of the adjacent fence covered when the gate is in the open position.
• Always be certain that the gate area is clear of pedestrians before operating the gate.
ROLE OF END USERS/HOME OWNER
•Entrapment Zone Hazard - Body parts may become entrapped between a gate and a stationary object
when the gate begins to move, which can result in serious injury or death. Pedestrians must stay clear
of the gate path, and any area where gate motion is close to stationary objects.
•Pinch Points Hazard - The opening mechanism may have arms that can overlap with a scissoring
effect, which can result in serious injury. Pedestrians must stay clear of the opening mechanism at all
times, particularly when gate is opening.
Be sure that warning signs are prominently displayed on both sides of the gate and any other place
where danger exists.
SWING GATE SYSTEMS

WARNINGS AND PRECAUTIONSWARNINGS AND PRECAUTIONSWARNINGS AND PRECAUTIONS
Warning - To reduce the risk of injury to persons,
The Miracle-1 isforVehicular Gate useONLY!
DO NOT install onANY pedestriangates.DO NOT install onANY pedestrianpassagewaysor
doorways.
DO NOT install upside down.
DO NOT install next to
sprinklers orany area that
may expose bottom of
operatorto water.
Caution - If the “Timer” isto be left inthe “ON”position, thenadd a safety loop and center loop.
DO NOT install ona few pickets, they will bend.
Weld a reinforcement baracross entire gate.
DO NOT over-bend the
cord from the operator.
Doing thiswill cause the
wiresto eventually break.
DO NOT install onuphill ordownhill gates.
Be sure to read and follow all these important instructions before installationof the gate operator. Elite
Access Systems, Inc. isnot responsible forimproperinstallationorfailure to comply with local building and
electrical codes.
IMPORTANT SAFETY INSTRUCTIONS
WARNING - To reduce the risk of severe injury ordeath:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Neverlet childrenoperate orplay with gate controls. Keep the remote control away from children.
3. Alwayskeep the moving gate insight and away from people and objectsuntil it iscompletely closed.
NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.
4. KEEP GATESPROPERLY MAINTAINED. Read the owner’smanual. Have a qualified service personperiodically inspect and
make repairs to gate hardware.
5. SAVE THESE INSTRUCTIONS.
8

10.25"
90° / 105°
8.5"
6"
7.75"
25.75"
Miracle 1 in Closed Position
Miracle 1 in Open Position
Gate in Closed Position
Gate in Open Position
Out
In
PROCEDURE FOR INSTALLATION
Typical Masonry Column Setup Typical Steel
Post Setup
Important:
Weld Re-Bar
Behind Gate
Hinges for
Maximum
Strength
Heavy Steel
Plates for
Reinforcement
(Not Supplied)
Heavy Steel Plates for
Reinforcement
(Not Supplied)
Gate Hinge
Gate Hinge
Steel Re-Bar
10"
Minimum
Back Steel Bracket
(Reinforce if necessary)
Back Steel Bracket
(Reinforce if
necessary)
Gate Hinge
Gate Hinge
Indexing on central hole in
the back steel bracket.
Indexing on
mounting hole in
the front steel
bracket.
6"
Top View
Post Setup
Heavy
Steel
Plate
Open To The Inside
9

Gate in Open Position
Gate in Closed Position
90° / 105°
7.75"
8.5"
25.75"
Out
In
PROCEDURE FOR INSTALLATION
Typical Masonry
Column Setup
Typical Steel
Post Setup
Top View
Post Setup
Indexing on central hole in
the back steel bracket.
Indexing on
mounting hole in
the front steel
bracket.
This Plate
Not Supplied
Back Steel
Bracket
(Reinforce
if necessary)
Back Steel Bracket
(Reinforce if necessary)
Heavy Steel Plates
for Reinforcement
(Not Supplied)
Heavy Steel
Plate
Gate Hinge
Gate HingeGate Hinge
6"
6"
Miracle 1 in Open Position
Miracle 1 in Closed Position
Important:
Weld Re-Bar
Behind Gate
Hinges for
Maximum
Strength
Steel Re-Bar
Gate Hinge
Heavy Steel Plate for
Reinforcement
(Not Supplied)
Open To The Outside
10

PROCEDURE FOR INSTALLATION
Step 3: Position the Miracle 1 horizontally level on the closed gate, where desired. For strength purposes, the
front steel bracket must be attached in an area that can withstand heavy forces . Additional reinforcement steel
plates may be necessary for mounting.
Step 4: Position and level the operator brackets and reinforcement plates. (See next page) . Tack weld brackets
and plates in position.
Step 1: Remove the 4 screws and lift the
operator cover off.
Step 2: Release the mechanical lock by turning the
key to the horizontal position.
If using a gate crossbar, weld bar across all pickets. Do not weld
the crossbar on a few pickets, or they will bend.
The Miracle 1 can be mounted on top
of the gate frame.
Important:
Tack weld the front steel
bracket at the top of the
crossbar, so the operator
will not hit the crossbar
when in motion.
Mounting Instructions
11

PROCEDURE FOR INSTALLATION
2.25" Vertical Height Difference
Step 4 (con't): The gate must be in the closed position. Make sure the operator is kept level while tack
welding the front and back steel brackets and reinforcement steel plates in position. After all tack welding is
finished,
remove the operator!
Caution: Welding the brackets with the operator attached to the gate may damage the operator.
Step 5: With the operator removed, completely weld around the brackets and plates on the gate.
Step 6: Remove the nut, bolt and bushing from
the back operator bracket. Place the metal bushing
in the hole of the steel bracket that will be used.
Secure operator with the nut and bolt (See Below).
Step 7: Remove the nut from the traveler carriage at
the front of the operator. Secure operator to the front
bracket with the washer and nut (See Below).
Metal
Bushing
Traveler
Carriage
Front Bracket
Back
Bracket
Mounting Instructions
Refer to Step 7
Refer to Step 6
Important:
These nuts MUST be tight or
unit will not work correctly!
Important:
Washer Must be placed
between traveler carriage
and TOP of front bracket.
12

Click!
PROCEDURE FOR INSTALLATION
Step 9: Lock the operator by turning the
key to the vertical position while pushing
or pulling on the gate until you hear the
key release click into place. The gate
should not move after the operator has
been locked. Completing this successfully
finishes the basic mounting of the
operator to the gate. The next steps are to
make all electrical connections to the
operator and control board.
Step 10: The following pages show the correct electrical procedures needed for the operator. After completing
all the electrical connections
, continue to step 11 to complete the final adjustments on the operator.
Mounting Instructions
Step 8: Make sure that the operator is level or it will not function properly. An off-level installation may
cause the gate or operator to fail prematurely.
Push or Pull
13

Step 11: Adjust the travel distance of the gate with the limit switches. Loosen the 2 screws of each limit switch
armature. Slide to adjust. Position the
outside limit switches of each armature to stop the gate in the “full open”
and “full closed” positions. Re-tighten armature screws when gate positions are correct.
Step 12: Reinstall the operator cover with the 4 screws to complete
the installation.
Outside Limit
Switch
Outside Limit Switch
Inside Limit
Switch
Inside Limit Switch
Limit Switch
Armature
Limit Switch Armature
Adjustment Screws
Adjustment Screws
PROCEDURE FOR INSTALLATION
Adjusting the Limit Switches
14

REMOVING THE CONTROL / SURGE BOARDS
MOUNTING THE CONTROL BOX
Remove the four nutsand remove battery rack.
Reverse thisprocess to reinstall.
Mount control box with four screwsand washers
(recommend #10 thru 1/4-20 BoltsorScrews)
Do Not overtighten.
Caution: Do Not make new mounting holes, orenlarge existing holesincontrol box.
Use the four mounting holesprovided.
BLACK
MOTOR
WHITE RED
BRAKE
SINGLEOR MASTER ONLY SLAVE ONLY
BROWN BLUE
LIMITS
GREEN BLACK
MOTOR
WHITE RED
BRAKE
BROWN BLUE
LIMITS
GREEN CENTER LOOP +24VAC INPUT SAFETY LOOP EXIT LOOP BURGLAR ALARM INPUT GROUND RADIO +24VOLT ULSENSOR
LAKEFOREST, CALIFORNIA
www.eliteaccess.com
REVA
MIRACLESURGE PROTECTION
1 2 3 4 5 6 7 8 9101112 13141516 1718192021222324252627
®
8
BLACK
MOTOR
WHITE RED
BRAKE
SINGLEOR MASTER ONLY SLAVE ONLY
BROWN BLUE
LIMITS
GREEN BLACK
MOTOR
WHITE RED
BRAKE
BROWN BLUE
LIMITS
GREEN CENTER LOOP +24VAC INPUT SAFETY LOOP EXIT LOOP BURGLAR ALARM INPUT GROUND RADIO +24VOLT ULSENSOR
LAKEFOREST, CALIFORNIA
www.eliteaccess.com
REVA
MIRACLESURGE PROTECTION
1 2 3 4 5 6 7 8 9101112 13141516 1718192021222324252627
®
Unscrew the 4 Phillipshead screwsfrom the cover.
Unplug the J1 and J3 plugs.
Unplug battery connector.
Unplug all accessory wiresfrom Surge Suppressor'sremovable
terminals.
Disconnect ground wire.
Remove three Phillipsscrewsfrom control board and remove board.
Remove three Phillipsscrewsfrom surge suppressorboard and
remove board.
POWER
CHARGEOK
BATTERYLOW
®
ACCESSSYSTEMS INCACCESS SYST EMS I NC
MAGLOCK
REPLACEFUSE
WHENLEDISON
REVERSE
SENSOR
SYSTEM
ON
ALARM
ALARM
SENSOR
OPEN
INSIDE
OFF
NO
YES
ON
TIMER
CENTRAL
STRIKE
OPEN
SAFETY
LOOPRADIO
REC
CENTER
LOOP
CONTROL
603
STOPBY
POSITIVE
STOP
OPEN
OUTSIDE
1
1
1
1
2
22
3
3
5
5
4
4
6
6
7
7
4
15

Install the Conduit (supplied) to
secure the wire to the Miracle 1
Control Board Box.
If the conduit can not be used, Install
a dedicated water tight conduit for 6
wires. DO NOT run AC wire in same
conduit as 6 wires!
More than 20 ft run, you MUST use
Shielded Wire for the blue and
green lines. Shield must be
grounded .
Important:
BLACK
MOTOR
WHITE RED
BRAKE
SINGLE OR MASTER ONLY SECOND ONLY
BROWN BLUE
LIMITS
GREEN BLACK
MOTOR
WHITE RED
BRAKE
BROWN BLUE
LIMITS
GREEN CENTER LOOP +24 VAC INPUT SAFETY LOOP EXIT LOOP BURGLAR ALARM INPUT GROUND RADIO +24 VOLT UL SENSOR
LAKE FOREST, CALIFORNIA
www.eliteaccess.com
REV A
MIRACLE SURGE PROTECTION
123456 789101112 13141516 171819 20 21 22 23 24 25 26 27
®
WIRING 1 OPERATOR TO BOARD
8
BLACK
MOTOR
WHITE RED
BRAKE
SINGLE OR MASTER ONLY SECOND ONLY
BROWN BLUE
LIMITS
GREEN BLACK
MOTOR
WHITE RED
BRAKE
BROWN BLUE
LIMITS
GREEN CENTER LOOP +24 VAC INPUT SAFETY LOOP STRIKE INPUT BURGLAR ALARM INPUT GROUND RADIO +24 VOLT UL SENSOR
LAKE FOREST,CALIFORNIA
www.eliteaccess.com
REV A
MIRACLE SURGE PROTECTION
123456 789101112 13141516 171819 20 21 22 23 24 25 26 27
®
Black White Red Brown Blue Green
123456
Removable Terminal
Connector
Supplied
Conduit
Removable
Terminal
Connector
Caution: Do Not over-bend the cord from the operator. Doing this will cause the
wires to eventually break.
Caution: Do Not use wire less than 16 gauge up to 200 Ft.
Caution: Make sure BARE WIRE
makes good contact inside
removable terminal connectors.
DO NOT let wire insulation
interfere with connection.
Wire
16

Supplied Conduit
Supplied
BLACK
MOTOR
WHITE RED
BRAKE
SINGLE OR MASTER ONLY SECOND ONLY
BROWN BLUE
LIMITS
GREEN BLACK
MOTOR
WHITE RED
BRAKE
BROWN BLUE
LIMITS
GREEN CENTER LOOP +24 VAC INPUT SAFETY LOOP EXIT LOOP BURGLAR ALARM INPUT GROUND RADIO +24 VOLT UL SENSOR
LAKE FOREST, CALIFORNIA
www.eliteaccess.com
REV A
MIRACLE SURGE PROTECTION
123456 789101112 13 14 15 16 17 1819 20 21 22 23 24 25 26 27
®
Black White Red Brown Blue Green Black White Red Brown Blue Green Shield
WIRING 2 OPERATORS MASTER / SECOND
6 Wires, 16 AWG from operator in dedicated water tight
conduit. DO NOT run AC lines in same conduit!
Water Tight
J-Box Kit
Elite # K55-09853
Master Second
Operator 2 (Second)
Operator 1 (Master)
BLACK
MOTOR
WHITE RED
BRAKE
SINGLE OR MASTER ONLY SECOND ONLY
BROWN BLUE
LIMITS
GREEN BLACK
MOTOR
WHITE RED
BRAKE
BROWN BLUE
LIMITS
GREEN CENTER LOOP +24 VAC INPUT SAFETY LOOP STRIKE INPUT BURGLAR ALARM INPUT GROUND RADIO +24 VOLT UL SENSOR
LAKE FOREST,CALIFORNIA
www.eliteaccess.com
REV A
MIRACLE SURGE PROTECTION
123456 789101112 13141516 171819 20 21 22 23 24 25 26 27
®
1 2 3 4 5 6 7 8 9 10 11 12
Removable Terminal Connectors
Install the Conduit (supplied) to secure
the Master Operator to the Control Board
Box.
Install a dedicated water tight conduit
for the Second Operator. DO NOT run AC
wire in same conduit as 6 wires!
More than 20 ft run, you MUST use
Shielded Wire for the blue and green
lines. Shield must be grounded .
Important:
Caution: Do Not use wire less than 16 gauge
up to 200 Ft.
Removable
Terminal
Connector
Water
Tight
Conduit
(Not
Supplied)
Caution: Make sure BARE WIRE
makes good contact inside removable
terminal connectors. DO NOT let wire
insulation interfere with connection.
Wire
17

CHOOSING GATE MOVEMENT DIRECTION
SENSOR ADJUSTMENT
Switch the “Open Inside / Open Outside” switch onthe control board
to the corresponding positionforthe properdirection.
Important: It isnecessary to still adjust your limit switch at the close position.
The controllerwill look forthe limit close first and thenit will look forthe positive stop.
Set the sensoradjustment so whenthe gate hitsany object while opening,
it will stop and whenthe gate hitsany object while closing, it will reverse.
Note: If youactivate the operatorand the gate stopsinthe middle of the
driveway, the sensorisset too sensitive.
The gate opens outward.
Adjusted by Qualified
Service Personnel
Maximum Sensitivity
Minimum
Sensitivity
The gate opens inward.
Caution: The sensors must be adjusted while the gate isinthe opening orclosing cycle.
Option –
Stop by Positive - Stop
Thisoptionisto be turned to
“yes” if the gate will use
positive stopsat the close
position.
8
8
18

19
EARTH GROUND ROD INSTALLATION
ADJUSTABLE TIMER
Use 12 gauge ground wire
Propergrounding givesanelectrical charge, such asfrom
anelectrical static discharge ora nearlightning strike, a
path from which to dissipate itsenergy safely into the
earth.
Without thispath, the intense energy generated by
lightning could be directed towardsthe Elite gate operator.
Although nothing canabsorb the tremendous powerof a
direct lightning strike, propergrounding canprotect the
gate operatorinmost cases.
The earth ground rod must be located within3 feet from
the gate operator. Use the propertype earth ground rod for
your area.
The ground wire must be a single, whole piece of wire.
Never splice two wiresforthe ground wire. If youshould
cut the ground wire too short, break it, ordestroy its
integrity, replace it with a single wire length.
8 Ft
Before digging more than18" deep, contact local underground utility locating companies
Avoid damaging gas, power, or other underground utility lines.
Chamberlain Professional Products is not responsible for improper
installation or failure to comply with all necessary local building codes.
Connect ground
wire to green
wire from surge
suppressor
board
Set Timer
1 to 60 Seconds
Timer On
Timer Off
If secondary safety sensor devices are not used when
timer is ON, gate will hit vehicle obstructing gate path.