Chamberlain SL600 User manual

• PLEASE READ THE MANUAL CAREFULLY BEFORE
INSTALLATION AND OPERATION
• THIS PRODUCT TO BE INSTALLED BY A TRAINED GATE
SYSTEMS TECHNICIAN ONLY.
SLIDE GATE OPERATOR
Models SL600 and SL1000
INSTALLATION MANUAL

2
TABLE OF CONTENTS
SAFETY
Safety Precautions For Slide and Ornamental Grill Type Gates................................................................3
Important Safety Information............................................................................................................... 4-5
INTRODUCTION
Specifications...........................................................................................................................................6
Carton Inventory......................................................................................................................................6
Tools Needed...........................................................................................................................................7
Overview of Gate Operator.......................................................................................................................7
INSTALLATION
Operator Dimensions...............................................................................................................................8
Prepare and Install the Mounting Plate.............................................................................................. 8-10
Install the Operator ................................................................................................................................11
Install Limit Switch Bracket ...................................................................................................................11
Disengage the Clutch.............................................................................................................................12
WIRING
Voltage Selection ...................................................................................................................................13
Power Wiring.........................................................................................................................................14
Install Entrapment Protection ...............................................................................................................15
Wiring Diagram......................................................................................................................................16
Battery Backup (Optional)......................................................................................................................17
TRAVEL LIMIT SETTINGS......................................................................................................................18
PROGRAMMING
Remote Control......................................................................................................................................18
Partial Open Setting...............................................................................................................................18
Erase All Codes......................................................................................................................................19
LiftMaster®Internet Gateway.................................................................................................................19
Erase a LiftMaster®Internet Gateway ....................................................................................................19
SETTINGS
Increased Starting Force........................................................................................................................20
Partial Open Setting...............................................................................................................................20
Auto Closing Setting..............................................................................................................................20
Limit Switch Setting...............................................................................................................................20
Force Adjustment...................................................................................................................................21
Soft Stop Setting ...................................................................................................................................21
Moving Speed Setting............................................................................................................................21
Opening/Closing Identification...............................................................................................................21
Flashing Light (Optional) .......................................................................................................................22
Photoelectric Sensor and Edge Sensor Connection...............................................................................22
OPERATION AND MAINTENANCE.................................................................................................... 23-25
TROUBLESHOOTING .............................................................................................................................26
REPAIR PARTS......................................................................................................................................27
ACCESSORIES .......................................................................................................................................28

3
MECHANICAL
ELECTRICAL
When you see these Safety Symbols and Signal Words on
the following pages, they will alert you to the possibility of
serious injury or death if you do not comply with the warnings
that accompany them. The hazard may come from something
mechanical or from electric shock. Read the warnings carefully.
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your gate and/or the gate
operator if you do not comply with the cautionary statements that
accompany it. Read them carefully.
Safety Precautions For Slide and Ornamental Grill Type Gates
SAFETY
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection contact edge sensing device MUST be installed to protect anyone who
may come near a moving gate.
• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID objects, such
as posts.
• A gate shall NOT open into public access ways.
• This operator is NOT intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the operator by a person responsible for their
safety.
• Children should be supervised to ensure that they DO NOT play with the operator.
• SAVE THESE INSTRUCTIONS.
IMPORTANT NOTE:
• BEFORE attempting to install, operate or maintain the operator, you must read and fully understand
this manual and follow all safety instructions.
• These instructions are intended to highlight certain safety related issues. These instructions are
not intended to be comprehensive. Because each application is unique, it is the responsibility of
the purchaser, designer, installer and end user to ensure that the total gate system is safe for its
intended use.
• Save These Instructions.

4
To reduce the risk of SEVERE INJURY or DEATH from an incorrect installation:
1. Vehicular gate systems provide convenience and security. Gate systems are comprised of many
component parts. The gate operator is ONLY one component. Each gate system is specifically
designed for an individual application.
2. Gate operating system designers, installers and users MUST take into account the possible
hazards associated with each individual application. Improperly designed, installed or maintained
systems can create risks for the user as well as the bystander. Gate systems design and
installation MUST reduce public exposure to potential hazards.
3. A gate operator can create high levels of force in its function as a component part of a gate
system. Therefore, safety features must be incorporated into every design. Specific safety
features include:
• Gate Edges • Guards for exposed rollers • Photoelectric Sensors
• Screen Mesh • Vertical Posts • Instructional and Precautionary Signage
4. Install the gate operator only when:
a. The operator is appropriate for the construction and the usage of the gate.
b. ALL openings of a horizontal slide gate are guarded or screened from the bottom of the gate
to a minimum of 4' (1.2 m) above the ground to prevent a 2 1/4" (6 cm) diameter sphere
from passing through the openings anywhere in the gate, and in that portion of the adjacent
fence that the gate covers in the open position.
c. ALL exposed pinch points are eliminated or guarded, and guarding is supplied for exposed
rollers.
5. The operator is intended for installation on gates used for vehicles. Pedestrians should be
supplied with a separate access opening.
6. The gate MUST be installed in a location so that enough clearance is supplied between the gate
and adjacent structures when opening and closing to reduce the risk of entrapment.
7. The gate MUST be properly installed and work freely in both directions prior to the installation
of the gate operator.
8. Controls MUST be far enough from the gate so that the user is prevented from coming in
contact with the gate while operating the controls.
9. BEFORE installing the drive, check that the driven part is in good mechanical condition, correctly
balanced and opens and closes properly.
SAFETY
IMPORTANT SAFETY INFORMATION

5
SAFETY
10. For a gate operator utilizing a non-contact sensor:
a. Reference owner’s manual regarding placement of non-contact sensor for each type of
application.
b. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips
the sensor while the gate is still moving.
c. One or more non-contact sensors shall be located where the risk of entrapment or
obstruction exists, such as the perimeter reachable by a moving gate or barrier.
11. For a gate operator utilizing a contact sensor such as an edge sensor:
a. A hard wired contact sensor shall be located and its wiring arranged so the communication
between the sensor and the gate operator is not subject to mechanical damage.
b. A wireless contact sensor such as the one that transmits radio frequency (RF) signals to the
gate operator for entrapment protection functions shall be located where the transmission of
the signals are not obstructed. A wireless contact sensor shall function under the intended
end-use conditions.
c. One or more contact sensors shall be located at the leading edge, trailing edge and post
mounted both inside and outside of a vehicular horizontal slide gate.
d. One or more contact sensors shall be located on the inside and outside leading edge of a
gate. Additionally, if the bottom edge of a gate is greater than 6" (15 cm) above the ground at
any point in its arc of travel, one or more contact sensors shall be located on the bottom
edge.
12. For horizontally moving pedestrian doors, ensure that entrapment between the driven part and
the surrounding fixed parts due to the movement of the driven part is avoided. This can be
achieved if the relevant distance does not exceed 8 mm. However, the following distances are
considered sufficient to avoid entrapments for the parts of the body identified:
a. For fingers, a distance greater than 25mm
b. For feet, a distance greater than 50mm
c. For heads, a distance greater than 300mm
d. For the whole body, a distance greater than 500mm
If these distances cannot be achieved, safeguarding devices must be provided.
IMPORTANT SAFETY INFORMATION
IMPORTANT: The MyQ feature and its accessories are not permitted for use in the countries of Peru
and Chile.

6
Specifications
INTRODUCTION
Carton Inventory
Main AC Supply: 110-127Vac / 220-240Vac; 50/60Hz
Motor Voltage: 24 Vdc
Input Power: 100 W
Ambient Temperature Range: -20 ~ +50 ˚C
Maximum Gate Weight: 600 Kg (Model SL600)
1000 Kg (Model SL1000)
Maximum Gate Width: 8 m
Maximum Pull Force (N): 780 (Model SL600)
970 (Model SL1000)
Protection Level: IP 44
Travel Speed: 22 cm/s
Daily Cycle Rate: Maximum 50 cycles per day
Gate Operator Weight: 6 Kg
Installation
Manual
(Not shown)
Remote Control, model TX4UNI (2)
M8x80 Expanding screw (4)
Mounting plate
Gate Operator
Release key (2)
M8 X40 Screw with
hexagon nut and plain
washer (4 sets)
Limit switch bracket (2)

7
Overview of Gate Operator
Tools Needed
Limit
Switch Bracket
Rack
Remote
Control
Gate
Operator
Gate
Photoelectric
Sensor
Flashing Light
Cables used must meet all National and Local Codes for outdoor use.
INTRODUCTION

8
Operator Dimensions
270 mm
294 mm
218 mm
INSTALLATION
3.98 cm
(1.57") 23.97 cm
(9.44")
30.47 cm (12")
39.97 cm
(15.74")
Figure 1
Prepare and Install the Mounting Plate
The instructions and illustrations in this manual are examples ONLY. Your installation may vary
depending on space, obstructions, and accessories. It is up to the installer to select the most suitable
solution.
1. Dig a hole to the side of the gate (Figure 1). The concrete pad should be deeper than the frost line.
Check all national and local codes.

9
INSTALLATION
1-3/4" (50 mm)
Figure 2
Figure 3
Figure 4
2. Prepare a trench and install the electrical
conduit. All conduit should be 3/4" diameter
maximum.
NOTE: The number of conduits will depend on
your site and the accessories to be installed.
3. Prepare a form box larger than the mounting
plate and insert the form box in the hole
(Figure 2). The form box should be 1-3/4" (50
mm) above the ground (Figure 2).
4. Insert an iron grid inside the form to reinforce
the concrete (Figure 2).
5. Fill the form box with concrete and wait for at
least 24 hours to allow the concrete to cure
(Figure 3).
6. Remove the form box (Figure 4).
7. Fill the hole around the concrete form with soil
(Figure 4).

10
INSTALLATION
11 cm
3 cm
TOP VIEW OF GATE
The distance between
the rack and the gate
should be 2.4 cm.
Gate
Rack
Mounting Plate
Mounting Plate
Rack
Figure 5
Cables
Figure 6
8. Position the mounting plate relative to the gate
(Figure 5).
9. Run all cables through the knockout (Figure 6).
10. Mark the mounting hole locations, drill with
a masonry bit. Screw the mounting plate into
place with provided anchoring hardware
(Figure 6).

11
INSTALLATION
Install the Operator
Make sure the sliding gate can be moved smoothly before installation. There must be a clearance
between rack and gear as shown, or the gate movement may be effected.
Limit Switch Bracket Installation
Attach the limit switch bracket to the rack with adjusting screws. If the limit switch bracket is installed
incorrectly, the gate cannot learn the travel limit.
110 mm
2-3 mm
Operator
Gate
Limit switch
bracket
Limit switch
spring
Rack
Gear
Wheel
Mounting plate
Track
Rack
Gear
Ground level
Limit switch
bracket
Limit switch bracket Adjust the limit
switch bracket
Adjusting screw
CORRECT INSTALLATION
Rack
INCORRECT INSTALLATION

12
INSTALLATION
Disengage the Clutch
Disengaged the clutch for the following reasons:
• To open or close the gate manually in case of power failure.
• To reset the functions.
• The operator needs maintenance.
1. Pull out the key guard.
2. Turn the release key, then pull manual release lever down to disengage the clutch.
3. To re-engage the clutch, return the manual release lever to the upright position making sure the
housing and release lever tabs are aligned and turn the release key to the lock position.
NOTE: Remember to lock the clutch after cover is in place and all operations are finished.
Key guard
Release key
Disengage
the clutch
Release key
Lock the clutch

13
To reduce the risk of SEVERE INJURY or DEATH:
• ANY maintenance to the operator or in the area near the operator MUST NOT be performed until
disconnecting the electrical power (AC or solar and battery). Upon completion of maintenance
the area MUST be cleared and secured, at that time the unit may be returned to service.
• Disconnect power at the fuse box BEFORE proceeding.
NOTE: The operator should be on a separate fused line of adequate capacity.
• ALL electrical connections MUST be made by a qualified individual.
• DO NOT install any wiring or attempt to run the operator without consulting the wiring diagram.
• ALL power wiring should be on a dedicated circuit and well protected.
• ALL power and control wiring MUST be run in separate conduit.
• BEFORE installing power wiring or control stations be sure to follow all specifications and
warnings described below. Failure to do so may result in SEVERE INJURY to persons and/or
damage to operator.
WIRING
Voltage Selection
The operator can be wired for either 110-127 Vac or 220-240 Vac through a jumper setting.
NOTE: Factory default jumper is installed for 220 Vac.
For 110-127 Vac installations:
1. Turn off the AC power from the main power
source circuit breaker.
2. Place the jumper on J3 and the cover on J2 on
the power board.
For 220-240 Vac installations:
1. Turn off the AC power from the main power
source circuit breaker.
2. Place the jumper on J2 and the cover on J3 on
the power board.
J3 J2
CN1
TR IN
TR OUT
CN3
110-127Vac 220-240Vac
J2
J3 OFF
ON ON
OFF
DC
+
CN4
BAT
CHCTR VBAT
CN2
CN7
PE
POWER LINE
NL
CN6
N 127V 230V
J3
J2
POWER BOARD

14
Power Wiring
The operator can be wired for either 110-127 Vac or 220-240 Vac.
1. Turn off the AC power from the main power
source circuit breaker.
2. Insert the AC power wires through the wire
input hole closest to the motor.
3. Connect the “hot” wire to the L terminal on the
power board.
4. Connect the neutral wire to the N terminal on
the power board.
5. Tighten the watertight connector nut.
6. Restore power to the operator.
WIRING
To reduce the risk of SEVERE INJURY or DEATH:
• DO NOT TOUCH the unused connections on J2 or J3 as they are energized.
• Replace cover before reconnecting or connecting power.
J3 J2
CN1
TR IN
TR OUT
CN3
110-127Vac 220-240Vac
J2
J3 OFF
ON ON
OFF
DC +CN4
BAT
CHCTR VBAT
CN2
CN7
PE
POWER LINE
NL
CN6
N 127V 230V
POWER BOARD
Power In

15
WIRING
Install Entrapment Protection Devices
Refer to Accessories page for the approved list of entrapment protection devices.
PHOTOELECTRIC SENSORS
The photoelectric sensor will function differently
depending on if it is connected to the IR1 or IR2
input. Refer to the "Settings" section on page 22 for
an explanation of the functionality.
1. Remove the factory jumper from the IR1 or IR2
input.
2. Connect the photoelectric sensor receiver to
IR1 and GND or IR2 and GND, depending on
the desired functionality.
3. Connect the photoelectric sensor transmitter to
IR+24V, IR1, and GND or to IR+24V, IR2, and
GND.
EDGE SENSOR
The Edge sensor can only be connected to the IR2
input.
1. Remove factory jumper from IR2 to GND.
2. Connect the edge sensor to IR2 and GND.
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect anyone who may come near a
moving gate.
• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as
posts or walls.
STOP
GND
IR2
SW2 SW1
GND
IR1
IR+24V
DCLAMP
+24V
CN3 CN2
CONTROL BOARD
Photoelectric
Sensor Receiver
IR1 Functionality
Photoelectric
Sensor Transmitter
STOP
GND
IR2
SW2 SW1
GND
IR1
IR+24V
DCLAMP
+24V
CN3 CN2
CN4
LED1 LED2 LED3 LED4 LED5
Edge Sensor
CONTROL BOARD
STOP
GND
IR2
SW2 SW1
GND
IR1
IR+24V
DCLAMP
+24V
CN3 CN2
IR2 Functionality
CONTROL BOARD
Photoelectric
Sensor Receiver
Photoelectric
Sensor Transmitter

16
WIRING
J3 J2
CN1
TR IN
TR OUT
CN3
110-127Vac 220-240Vac
J2
J3 OFF
ON ON
OFF
DC
+
CN4
BAT
CHCTR VBAT
CN2
CN7
PE
POWER LINE
NL
CN6
N
127V 230V
STOP
GND
IR2
SW2 SW1
GND
IR1
IR+24V
DCLAMP
+24V
CN3 CN2
M1M2
MOTOR DC
CN1
CN4
RV
FORCE LV
SBC
S2 S1
ON
1234 5678
ON
LED1 LED2 LED3 LED4 LED5
RF
LEARN
Transformer
(Input)
POWER IN
Backup Battery
Operator
Operator
Antenna
POWER BOARD
CONTROL BOARD
Transformer
(Out)
Emergency Stop
Switch
Limit Switch
Photoelectric
Sensor
DC Flashing
Light
Photoelectric Sensor or Edge
SBC is an
open/close
command for a
single gate.

17
WIRING
Battery Backup (Optional)
The batteries are charged in the circuit by the integrated transformer. Recommended items for a battery
backup application (not provided):
• Two 12V 4Ah batteries (McNair Model RB-FM-12V-4AH)
• Battery box (Attwood Model 9069-1)
• 3 x 18 AWG (1.00 mm) VM-1 105˚C 600V, 1 wire must have a 10A/250V in-line fuse
1. Disconnect AC power to the operator.
2. Insert the battery power wires through the same hole as the AC power wires.
3. Connect the battery cable to the BATTERY terminals on the power board.
4. Install battery box in desired location (no further than 10 feet from the operator).
5. Place the batteries in the battery box.
6. Connect a jumper with an in-line fuse between the positive (+) terminal on one battery and the
negative (-) terminal on the other battery.
7. Connect the positive battery cable wire to the positive (+) terminal on the battery.
8. Connect the negative battery cable wire to the negative (-) terminal on the other battery.
9. Reconnect AC power to the operator.
10. Place cover on the operator.
J3 J2
CN1
TR IN
TR OUT
CN3
110-127Vac 220-240Vac
J2
J3 OFF
ON ON
OFF
DC
+
CN4
BAT
CHCTR VBAT
CN2
CN7
PE
POWER LINE
NL
CN6
N 127V 230V
POWER BOARD
Jumper with
10A/250V
in-line fuse
(not provided)
+-

18
The travel limits can be set when the gate is closed or opened.
1. Press and hold the
SBC
button for 5 seconds. The DL5 will flash.
2. Press the remote control or
SBC
button.
3. The gate will open or close and stop when the limit switch bracket reaches the switch spring. The
gate operator will save the setting information.
The operator should move in the close direction first when setting the limits. If the gate moves in the
open direction flip the #5 dip switch to the opposite position.
NOTE: The gate operator will exit programming after 30 seconds of inactivity.
TRAVEL LIMIT SETTINGS
PROGRAMMING
Remote Control
1. Press and release the
LEARN
button, LED1 will light.
2. Press the remote control button that you would like to program.
The operator will automatically exit learn mode (LED1 will flash and go out) if programming is
successful. To program additional Security+ 2.0™ remote controls or remote control buttons, repeat
the programming steps above. Press the LEARN button a second time to exit programming at any time.
Partial Open Setting
1. Press and release the
LEARN
button, LED1 will light.
2. Press and release the
LEARN
button again, LED1 will begin flashing.
3. Press the remote control button that you would like to program to the partial open setting (must be
different than button controlling normal operation).
NOTICE: Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for this product could void the user’s authority to operate the equipment.
This device is designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

19
PROGRAMMING
Erase All Codes
1. Press and hold the
LEARN
button, LED2 will light.
2. Hold the LEARN button for approximately 8 seconds. LED1 will go out and all remote control codes
are now erased.
LiftMaster®Internet Gateway
IMPORTANT: The MyQ feature, Internet Gateway and its accessories are not permitted for use in the
countries of Peru and Chile.
To program the operator to the LiftMaster®Internet Gateway:
1. Connect the Ethernet cable to the LiftMaster®Internet Gateway and the router.
2. Connect power to the LiftMaster®Internet Gateway.
3. Create an online account by visiting www.myliftmaster.com.
4. Register the LiftMaster®Internet Gateway.
5. Use an internet enabled computer or smartphone to add devices. The LiftMaster®Internet Gateway
will stay in learn mode for three minutes.
6. Press the LEARN button on the operator (LED1 will light as it enters learn mode). The LiftMaster®
Internet Gateway will pair to the operator if it is within range and LED1 will flash and go out if
programming is successful.
Erase a LiftMaster®Internet Gateway
1. Press and hold the
LEARN
button, LED1 will light.
2. Hold the LEARN button for approximately 8 seconds. LED1 will go out and all remote control codes
are now erased.
3. Press and hold the LEARN button a second time, LED1 will light again.
4. Hold the LEARN button for approximately 8 seconds. LED1 will go out and all gateways are now
erased.

20
Increased Starting Force
When activated, the operator will run with higher
force for first 2+/-1 seconds than the normal
running force.
1 ON = Higher starting force
1 OFF = Standard starting force
Partial Open Setting
When on, the partial open setting will open the
gate 1 meter. Refer to the Programming section for
instructions to program the remote control for this
setting.
2 ON = Partial Open ON
2 OFF = Partial Open OFF
Auto Closing Setting
Switches shall be used to set timer to close
duration from 0-105 seconds by adding the values
of each switch in the ON position. Each switch
value shall be the following:
6 ON = 15 seconds
7 ON = 30 seconds
8 ON = 60 seconds
Limit Switch Setting
Factory default is set to OFF (normal open).
4 ON = Travel limit switch is set to
normal close
4 OFF = Travel limit switch is set to
normal open
1 2 3 4 5 6 7 8
S1
ON
OFF
Increased Starting Force is on
SETTINGS
1 2 3 4 5 6 7 8
S1
ON
OFF
Partial Open is on
1 2 3 4 5 6 7 8
S1
30 Seconds
ON
OFF
1 2 3 4 5 6 7 8
S1
Normal open
ON
OFF