Champion Power Equipment 11051 System manual

OWNER’S MANUAL & OPERATING INSTRUCTIONS
WINCH KIT
with SPEED MOUNT™HITCH ADAPTER
12039 Smith Ave.
Santa Fe Springs CA 90670
USA / 1-877-338-0999
www.championpowerequipment.com
SAVE THESE INSTRUCTIONS
Important safety instructions
are included in this manual.
MADE IN CHINA
REV 11051-20160127
4536 kg (10,000 lb.)
11051
MODLE NUMBER

5
ENGLISH 11051
Read this owner’s manual before operating your winch. Familiarize yourself with the location and
function of the controls and features. Save this manual for future reference.
CONTROLS AND FEATURES
Winch
(1) Motor – 3.6 HP (2.7 kW) 12V DC motor
provides power to the planetary gear
mechanism.
(2) Braking System – Braking action is
automatically applied to the winch drum by
a separate mechanical brake when the winch
motor is stopped and there is a load on the
wire rope.
(3) Solenoid – Power from the vehicle battery
flows through the weather sealed solenoid
switch before being directed to the winch
motor.
(4) Free Spooling Clutch – The clutch allows the
operator to manually disengage (“Out”) the
spooling drum from the gear train, free spool.
Engaging the clutch (“In”) locks the winch into
the gear system.
(5) Planetary Gear System – The reduction gears
convert the winch motor power into extreme
pulling forces. This system allows high torque
while maintaining compact size and light
weight.
(6) Speed Mount™ Hitch Adapter – Adapter
for front or rear end class III hitch receiver
mounting and off-vehicle storage.switch before
being directed to the winch motor.
(7) Quick Connect Leads – 1.8 m (6 ft.) heavy
duty cables with quick connect leads.
(8) Remote Switch – Dual switches for powering
the rope in or out of your winch drum.
(9) Clevis Hook - Provides a means for connecting
the looped ends of cables to an anchor.
(10) Wire Rope – 9.2 mm x 26 m (3/8 in. x 85 ft.)
galvanized aircraft cable designed specifically
for load capacity of 4536 kg (10,000 lb.).
(11) Snatch Block – Used properly, the snatch
block can double the pulling power of winch,
or change your pulling directly without
damaging the wire rope.
(12) Roller Fairlead – When using the winch at an
angle the roller fairlead acts to guide the wire
rope onto the drum and minimizes damage
to the wire rope from abrasion on the winch
mount or bumper.
(13) Winch Drum – The winch drum is the cylinder
on which the wire rope is stored. It can feed or
wind the rope depending on the remote winch
switch.
1
13
6
8
4
3
9
7
12
10
11
5
2

10
11051 ENGLISH SPECIFICATIONS
Performance Specifications
– Rated Pull ..................................... 4536 kg (10,000 lb.)
– Gear Reduction Ratio ....................................... 216:1
– Motor.......................... Series Wound Motor 3.6 HP/2.7 kW (12V DC)
– Duty Cycle ..................................... Intermittent Use Only
– Drum Size.................... 63 mm (D) x 224.5 mm (L) [2.5 in. (D) x 8.8 in. (L)]
– Cable......................... 9.2 mm (D) x 26 m (L) [3/8 in. (D) x 85 ft. (L)]
– Gross Weight...................................... 57 kg (125.7 lb.)
– Net Weight....................................... 53 kg (116.8 lb.)
– Height......................................... 26.7 cm (10.5 in.)
– Width.......................................... 14.2 cm (5.6 in.)
– Length ........................................ 55.5 cm (21.9 in.)
– Bolt Pattern............................ 25.4 cm x 11.4 cm (10 in. x 4.5 in.)
Line Speed and Motor Current (First Layer)
Line Pull LB 02000 4000 6000 8000 10000
KG 0907 1814 2722 3629 4536
Line Speed (12V DC) FPM 15.7 9.8 7.2 5.9 4.9 3.9
MPM 4.8 3.0 2.2 1.8 1.5 1.2
Max Current A115 175 220 280 320 400
Run Time* Minutes 111111
Cooling Time** Minutes 555555
Line Pull and Cable Capacity Per Layer
Line of Cable 1234
Rated Line Pull LB 10000 8000 6600 5600
KG 4536 3629 2994 2540
Cable Capacity FT 18 39.4 64 85
M 5.5 12 19.5 26
– Use double line and snatch block for pulling loads over 50%.
* If the motor becomes uncomfortably hot to the touch, stop winching immediately and let it cool down for 5 minutes. Do not
pull for more than one minute at or near the rated load.
** Electric winches are designed and made for intermittent use and should not be used in constant duty applications.