Champion Power Equipment 11051 System manual

OWNER’S MANUAL & OPERATING INSTRUCTIONS
WINCH KIT
with SPEED MOUNT™HITCH ADAPTER
10006 Santa Fe Springs Road
Santa Fe Springs CA 90670
USA / 1-877-338-0999
www.championpowerequipment.com
SAVE THESE INSTRUCTIONS
Important Safety Instructions
are included in this manual.
MADE IN CHINA
REV 11051-20131115
4536 kg (10,000 lb.)
11051
MODLE NUMBER

*We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on the cover.
Have questions or need assistance?
Do not return this product to the store!
WE ARE HERE TO HELP!
Visit our website:
www.championpowerequipment.com
for more info:
• Product Info & Updates
•Frequently Asked Questions
• Tech Bulletins
• Product Registration
– or –
Call our Customer Care Team Toll-Free at:
1-877-338-0999

11051
4536 kg (10,000 lb.)
WINCH KIT
TABLE OF CONTENTS
Introduction....................1
Introduction.................. 1
This Booklet ................. 1
Accessories.................. 1
Manual Conventions ............... 2
Safety Rules ................... 3
Controls and Features .............. 5
Winch..................... 5
Assembly ..................... 6
Mounting................... 6
Mounting the Winch........... 6
Operation..................... 7
General Tips for Safe Operation....... 7
Self Recovery................. 7
Winching Techniques A-Z .......... 8
Maintenance ................... 9
Lubrication.................. 9
Cable Assembly Replacement........ 9
Specifications.................. 10
Performance Specifications........ 10
Parts Diagram ............... 11
Parts List.................. 12
Troubleshooting................. 13
Warranty..................... 14
Warranty Qualifications .......... 14
Repair/Replacement Warranty....... 14
Do Not Return The Unit
To The Place Of Purchase ......... 14
Warranty Exclusions............ 14
Limits of Implied Warranty
And Consequential Damage........ 14
Contact Information ............ 14
Address................. 14
Customer Service ........... 14
Technical Service ........... 14
with SPEED MOUNT™HITCH ADAPTER

1 REV 11051-20131115
ENGLISH 11051
INTRODUCTION
Introduction
Congratulations on your purchase of a Champion
Power Equipment winch. CPE designs and builds
winches to strict specifications. With proper use
and maintenance, this winch will bring years of
satisfying service.
This Booklet
Every effort has been made to ensure the accuracy
and completeness of the information in this manual.
We reserve the right to change, alter and/or improve
the product and this document at any time without
prior notice.
Accessories
Champion Power Equipment manufactures and
sells accessories designed to help you get the
most from your purchase. To find out more about
our covers, tree savers, hooks, fairleads, etc.,
please visit our web site at:
www.championpowerequipment.com
Record the model and serial numbers as well as date and place of purchase for future reference. Have
this information available when ordering parts and when making technical or warranty inquiries.
Champion Power Equipment Support
Model Number
Serial Number
Date of Purchase
Purchase Location
1-877-338-0999
11051

REV 11051-20131115 2
11051 ENGLISH
This manual uses the following symbols to help differentiate between different kinds of information.
The safety symbol is used with a key word to alert you to potential hazards in operating and owning
power equipment.
Follow all safety messages to avoid or reduce the risk of serious injury or death.
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
CAUTION
CAUTION used without the safety alert
symbol indicates a potentially hazardous
situation which, if not avoided, may result in
property damage.
CAUTION
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
DANGER
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
WARNING
If you have questions regarding your winch,
we can help. Please call our help line at
1-877-338-0999
NOTE
MANUAL CONVENTIONS

3 REV 11051-20131115
ENGLISH 11051
Do not use this winch for lifting or moving
people or animals.
DANGER
Keep yourself and others a safe distance to
the side of the cable when under tension.
DANGER
Never step over a cable or near a cable under
load.
DANGER
Read this manual thoroughly before operating
your winch. Failure to follow instructions could
result in serious injury or death.
WARNING
Do not exceed the rated capacity.
WARNING
The wire rope may break before the motor
stalls. For heavy loads at or near rated
capacity, use a pulley block/snatch block to
reduce the load on the wire rope.
WARNING
Do not move the vehicle to pull a load
(towing) on the winch cable. This could result
in cable breakage.
WARNING
Do not use the winch to secure or hold a
vehicle for a long period of time. Do not use
the winch to secure a vehicle for transport.
WARNING
Disconnect the remote control and battery
leads when not in use.
WARNING
Pull only on areas of the vehicle as specified
by the vehicle manufacturer.
WARNING
Avoid “shock loads” by using the control
switch intermittently to take up the slack in
the wire rope. “Shock loads” can far exceed
the rate capacity for the wire rope and drum.
Do not accelerate your vehicle while winching.
Loss of traction can cause a shock load on
the cable.
WARNING
Batteries contain acid and produce explosive
gases.
Keep sparks, flames and cigarettes away from
batteries at all times. Wear safety glasses and
protect the eyes at all times. Do not lean over
the batteries during operation.
WARNING
SAFETY RULES

REV 11051-20131115 4
11051 ENGLISH
Do not use as a hoist. Do not use for overhead
lifting.
WARNING
When re-spooling the cable, ensure that the
cable spools in the under-wind position with
the cable entering the drum from the bottom,
not the top.
To re-spool correctly, and while wearing
gloves, keep a slight load on the cable while
pushing the remote button to draw in the
cable. Walk toward the winch not allowing the
cable to slide through your hands. Do not let
your hands get within 30 cm (12 in.) of the
winch while re-spooling. Turn off the winch
and repeat the procedure until a few feet of
cable are left. Disconnect the remote control
and finish spooling by rotating the drum by
hand with the clutch disengaged. Keep hands
clear of the fairlead and drum while the winch
is under power .
WARNING
Use gloves to protect hands when handling
the cable. Never let the cable slide through
your hands.
CAUTION
Never release the free-spool clutch when
there is a load on the winch.
CAUTION
Use hook strap when handling the hook for
spooling or unspooling the wire rope.
CAUTION
Do not wrap the cable around any object and
hook it back onto itself.
CAUTION
Apply blocks to the wheels of the vehicle
when on an incline.
CAUTION
Duration of winching pulls should be kept as
short as possible.
If the motor becomes uncomfortably hot to
the touch, stop winching immediately and let
it cool down for a few minutes. Do not pull for
more than one minute at or near the rated load.
CAUTION
If the motor stalls, do not maintain power to
the winch.
Electric winches are designed and made for
intermittent use and should not be used in
constant duty applications.
CAUTION
SAFETY RULES

5 REV 11051-20131115
ENGLISH 11051
Read this owner’s manual before operating your winch. Familiarize yourself with the location and
function of the controls and features. Save this manual for future reference.
CONTROLS AND FEATURES
Winch
(1) Motor – 3.6 HP 12V DC motor provides power
to the planetary gear mechanism.
(2) Braking System – Braking action is
automatically applied to the winch drum by
a separate mechanical brake when the winch
motor is stopped and there is a load on the
wire rope.
(3) Solenoid – Power from the vehicle battery
flows through the weather sealed solenoid
switch before being directed to the winch
motor.
(4) Free spooling Clutch – The clutch allows the
operator to manually disengage (“Out”) the
spooling drum from the gear train, free spool.
Engaging the clutch (“In”) locks the winch into
the gear system.
(5) Planetary Gear System – The reduction gears
convert the winch motor power into extreme
pulling forces. This system allows high torque
while maintaining compact size and light
weight.
(6) Speed Mount™ Hitch Adapter – Adapter
for front or rear end class III hitch receiver
mounting and off-vehicle storage.switch before
being directed to the winch motor.
(7) Quick Connect Leads – 1.8 m (6 ft.) heavy
duty cables with quick connect leads.
(8) Remote Switch – Dual switches for powering
the rope in or out of your winch drum.
(9) Clevis Hook - Provides a means for connecting
the looped ends of cables to an anchor.
(10) Wire Rope – 9.2 mm x 26 m
(3/8 in. x 85 ft.) galvanized aircraft cable
designed specifically for load capacity of
4536 kg (10,000 lb.).
(11) Snatch Block – Used properly, the snatch
block can double the pulling power of winch,
or change your pulling directly without
damaging the wire rope.
(12) Roller Fairlead – When using the winch at an
angle the roller fairlead acts to guide the wire
rope onto the drum and minimizes damage
to the wire rope from abrasion on the winch
mount or bumper.
(13) Winch Drum – The winch drum is the cylinder
on which the wire rope is stored. It can feed or
wind the rope depending on the remote winch
switch.
1
13
6
8
4
3
9
7
12
10
11
5
2

REV 11051-20131115 6
11051 ENGLISH
This CPE 4536 kg (10,000 lb.) winch is designed
with a bolt pattern that is standard in this class
of winch. Many winch mounting kits are available
that utilize this bolt pattern for the most popular
trucks and Sport Utility Vehicles. If you cannot
find a kit locally, contact CPE and we will provide
you with the name of a dealer near you.
If you will utilize the CPE Speed Mount™ Hitch
Adapter, you must ensure that the three major
sections (motor, drum and gear housing) are
properly aligned. Proper alignment of the winch
will allow even distribution of the full rated load.
Mounting bolts must be SAE grade 5 or better
and torque to 34 ft. lbs.
CAUTION
Battery cables should not be drawn taut.
Leave some slack for cable movement.
CAUTION
ASSEMBLY
FUNCTION PROPERLY: Connect the red
(positive) lead of the quick connect to the
positive (+) terminal of the vehicle’s 12 volt
battery. Connect the black (negative) lead of
the quick connect to the negative (–) terminal
of the vehicle’s 12 volt battery.
Mounting the Winch
1. Insert 2 M10x35 bolts to the mounting
channel hole and attach the roller fairlead to
the mounting channel with the 2 flat washers,
lock washers and Nut M10 provided.
2. Extend the arms of the Speed Mount™ Hitch
Adapter and secure with 4 M8 bolts and M8
nuts.
3. Turn the winch up-side-down; insert 4 M10
nuts into the holes of the winch.
4. Place the Speed Mount™ Hitch Adapter on
the winch, making sure the winch is centered
in the middle of the mounting channel.
Disengage the clutch by moving the cam ring
to the “Out” position. Release the wire rope
and pull through the slot in the front of the
channel.
5. Attach using the 4 M10 Cap Screws with 4
lock washers and flat washers into the hole.
6. Attach the clevis hook and hand strap.
7. Insert the Speed Mount™ Hitch Adapter into
your hitch receiver and secure with the pin.
8. Connect the battery leads. FOR WINCH TO
9. Insert the male quick connect into the female
quick connect to complete the wiring.
10. Attach the remote lead to the winch and test
for proper operation.
11. Check for proper drum rotation. Turn the
clutch handle to the “out” position (free
spooling). Pull out some cable from the drum,
and then turn the clutch knob to the “In”
position to engage the gears. Press the cable
out button on the power switch. If the drum
is turning and releasing more cable then
your connections are accurate. If the drum
is turning and collecting more cable then
reverse the leads on the motor. Repeat and
check rotation.
Mounting the Winch Cont’d.
NEVER route electrical cables across any
sharp edges, through and/or near moving
parts, or near parts that may become hot.
CAUTION
Mounting

7 REV 11051-20131115
ENGLISH 11051
OPERATION
General Tips for Safe Operation
Your 11051 winch is rated at a 4536 kg
(10,000 lb.) capacity in first layer (max) when
spooling the first rope layer on the drum. Overloads
can damage the winch, motor and/or wire rope. For
loads over
3629 kg (8000 lb.) we recommend the use of the
pulley block/snatch block to double the wire rope
line. This will aid in two ways:
(a) reduce the number or rope layers on the drum,
as well as,
(b) reduce the load on the wire rope by as much
as 50%.
When doubling the line back to the vehicle,
attach to the tow hook, frame or other load bearing
part. The vehicle engine should be kept running
during operation of the winch to minimize battery
drain and maximize power and speed of the winch.
If the winch is used for a considerable time with
the engine off the battery may be drained and too
weak to restart the engine.
Get to know your winch before you actually need to
use it. We recommend that you set up a few test
runs to familiarize yourself with rigging techniques,
the sounds your winch makes under various loads,
the way the cable spools on the drum, etc.
Inspect the wire rope and equipment before each
use. A frayed or damaged rope shall be replaced
immediately. Use only manufacturer’s identical
replacement rope with the exact specifications.
Inspect the winch installation and bolts to ensure
that all bolts are tight before each operation. Store
the remote control inside your vehicle in a place
that it will not be damaged.
Any winch that appears to be damaged in any way,
is found to be worn, or operates abnormally MUST
BE REMOVED FROM SERVICE UNTIL REPAIRED.
It is recommended that the necessary repairs
be made by a manufacturer’s authorized repair
facility.
Pull only on areas of the vehicle as specified by
the vehicle manufacturer. Only attachments and/
or adapters supplied by the manufacturer are to
be used.
Self Recovery
Locate a suitable anchor such as a strong tree trunk
or boulder. Always use a sling as an anchor point.
A roller fairlead (included) will help guide the wire
rope and to reduce binding on short side pulls. Do
not winch from an acute angle as the wire rope will
pile up on one side of the drum causing damage to
wire rope and the winch.
Short pulls from an angle can be used to straighten
the vehicle. Long pulls should be done with the wire
rope at a 90° angle to the winch/vehicle.
When pulling a heavy load, place a blanket or jacket
over the wire rope 1.5 m - 1.8 m (5 ft. - 6 ft.) from
the hook.
In the event of a broken cable it will dampen
the snap back. For additional protection open
the hood of the vehicle. For pulls over 3629 kg
(8000 lb.), we recommend the use of the snatch
block/pulley block to double line the wire rope.
This reduces the load on the winch and the strain
on the rope by approximately 50%.
RIGHT WRONG
SINGLE LINE DOUBLE LINE

REV 11051-20131115 8
11051 ENGLISH
OPERATION
Winching Techniques A-Z
(a) Take time to assess your situation and plan
your pull.
(b) Put on gloves to protect your hands.
(c) Disengage the clutch to allow free- spooling
and also save battery power.
(d) Attach the hook strap to the clevis hook.
(e) Pull out the wire rope to your desired anchor
point using the hook strap.
(f) Secure the clevis hook to the anchor point:
Sling, chain or snatch block. Do not attach
the hook back onto the wire rope.
(g) Engage the clutch.
(h) Connect the remote control to the winch. If
you are going to control the winch from inside
your vehicle then pass the remote through an
open window to avoid the wires being pinched
in the door.
(i) Start your engine to ensure power is being
replenished to the battery.
(j) Drape a blanket or jacket over the wire rope
approximately 1.5 m - 1.8 m (5 ft. - 6 ft.)
from the hook. Open the hood for added
protection.
(k) Power in the wire rope guiding the wire under
tension to draw up the slack in the wire. Once
the wire is under tension, stand clear. Never
step over the wire rope.
(l) Double check your anchors and make sure all
connections are secure.
(m) Inspect the wire rope. Make sure there are at
least 5 wraps of wire rope around the winch
drum.
(n) Clear the area. Make sure all spectators stand
clear and that no one is directly in front or
behind the vehicle or anchor point.
(o) Begin winching. Be sure that the wire rope
is winding evenly and tightly around the
drum. The vehicle that is being winched can
be slowly driven to add assistance to the
winching process. Avoid shock loads; keep
the wire rope under tension.
Winching Techniques A-Z Cont’d.
(p) The vehicle to be winched should be placed
in neutral and the emergency brake released.
Only release the brake pedal when under full
tension. Avoid shock loads to the winch. This
can damage the winch, rope and vehicle.
(q) The winch is meant for intermittent use.
Under full load with a single line rig do not
power in for more than a minute without
letting the motor cool down for a few minutes
and then resume the winching operation.
(r) The winching operation is complete once the
vehicle is on stable ground and is able to
drive under its own power.
(s) Secure the vehicle. Be sure to set the brakes
and place the vehicle in park.
(t) Release the tension on the wire rope. The
winch is not meant to hold the vehicle for
long periods of time.
(u) Disconnect the wire rope from the anchor.
(v) Rewind the wire rope. Make sure that any wire
already on the drum has spooled tightly and
neatly. If not, draw out the wire and re-spool
from the point where the rope is tight.
(w) Keep your hands clear of the winch drum and
fairlead as the wire rope is being drawn in.
(x) Secure the hook and hook strap.
(y) Disconnect the remote control and store in a
clean, dry place.
(z) Clean and inspect connections and mounting
hardware for next winching operation.

9 REV 11051-20131115
ENGLISH 11051
MAINTENANCE
The owner/operator is responsible for all periodic
maintenance.
Lubrication
All moving parts within the electric winch having
been lubricated using high temperature lithium
grease at the factory. No internal lubrication is
required. Lubricate cable assembly periodically
using a light penetrating oil.
Cable Assembly Replacement
It is recommended that any modifications be
performed by a manufacturer’s authorized repair
facility, and that only manufacturer-supplied parts
be used.
1. Move the clutch to the “Out” position.
2. Extend cable assembly to its full length. Note
how the existing cable is connected to the
inside of the drum.
3. Remove old cable assembly and attach new
one.
4. Retract cable assembly onto drum being
careful not to allow kinking.
Complete all scheduled maintenance in a timely
manner. Correct any issue before operating the
winch.
Never operate a damaged or defective winch.
WARNING
Improper maintenance will void your warranty.
WARNING
For service or parts assistance, contact our
help line at 1-877-338-0999
NOTE

REV 11051-20131115 10
11051 ENGLISH
SPECIFICATIONS
Performance Specifications
– Rated Pull ..................................... 4536 kg (10,000 lb.)
– Gear Reduction Ratio ....................................... 216:1
– Motor.......................... Series Wound Motor 3.6 HP/2.7 kW (12V DC)
– Duty Cycle ..................................... Intermittent Use Only
– Drum Size.................... 63 mm (D) x 224.5 mm (L) [2.5 in. (D) x 8.8 in. (L)]
– Cable ......................... 9.2 mm (D) x 26 m (L) [3/8 in. (D) x 85 ft. (L)]
– Gross Weight...................................... 57 kg (125.7 lb.)
– Net Weight....................................... 53 kg (116.8 lb.)
– Height......................................... 26.7 cm (10.5 in.)
– Width.......................................... 14.2 cm (5.6 in.)
– Length ........................................ 55.5 cm (21.9 in.)
– Bolt Pattern............................ 25.4 cm x 11.4 cm (10 in. x 4.5 in.)
Line Speed and Motor Current (First Layer)
Line Pull LB 02000 4000 6000 8000 10000
KG 0907 1814 2722 3629 4536
Line Speed (12V DC) FPM 15.7 9.8 7. 2 5.9 4.9 3.9
MPM 4.8 3.0 2.2 1.8 1.5 1.2
Max Current A115 175 220 280 320 400
Run Time* Minutes 111111
Cooling Time** Minutes 555555
Line Pull and Cable Capacity Per Layer
Line of Cable 1234
Rated Line Pull LB 10000 8000 6600 5600
KG 4536 3629 2994 2540
Cable Capacity FT 18 39.4 64 85
M 5.5 12 19.5 26
– Use double line and snatch block for pulling loads over 3629 kg (8000 lb.).
* If the motor becomes uncomfortably hot to the touch, stop winching immediately and let it cool down for 5 minutes. Do not
pull for more than one minute at or near the rated load.
** Electric winches are designed and made for intermittent use and should not be used in constant duty applications.

11 REV 11051-20131115
ENGLISH 11051
SPECIFICATIONS
Parts Diagram

REV 11051-20131115 12
11051 ENGLISH
Parts List
#Part Number Description Qty
1P1010100 Gear Carrier Assembly
- Input 1
2P1010200 Gear Carrier Assembly
- Intermediate 1
3P1010300-N Gear Carrier Assembly
- Output 1
4P1010400 Cable Assembly 1
5P1011001-B Switch Assembly
- Black 1
6P1011002-BF Up-setting Solenoid
Assembly - Black Flat 1
7P1011003-BF Motor/End Bearing
Assembly - Black Flat 1
8P1011021 Gear Housing A 1
9810600-NA Brake Assembly 1
10 P1010900-N-BF Drum Assembly
- Black Flat 1
11 P1011005-N-BF Gear Housing End
Cover - Black Flat 1
12 P1011022 Pan Head Screw
M5x15 1
13 P1011023 Washer ø5 1
14 P1011024 Clutch Handle 1
15 P1011025 Clutch Seat 1
16 P1011026 Seal Ring ø20x1.8 1
17 P1011027 Spring 1
18 P1011028 Clutch Pin 1
19 P1011029 Set Screw M4x8 1
20 P1011010 Gear Housing End
Cover Seal 1
21 P1011030 Gear Housing B 1
22 P1011012 Bushing 1
23 P1011013 Thrust Washer 1
24 P1011014 Motor/End Bearing
Seal 2
25 P1011015-N-BF End Bearing - Black
Flat 1
#Part Number Description Qty
26 P1011016 Lock Washer ø6 8
27 P1011017 Cap Screw M6×20 8
28 P1011018 Thrust Disc 2
29 P1010008 Bushing - Drum 1
30 P1010012 Cap Screw M6×10 1
31 P1010013 Lock Nut M8 4
32 P1010014 Cap Screw M8×22 4
33 P1010015 Motor/Drum Bushing 1
34 810024 Lock Nut M10 6
35 810023 Flat Washer ø10 6
36 810022 Lock Washer ø10 6
37 810021 Cap Scerw M10×35 6
38 810025-N Terminal Protector 3
39 410022 Yellow Strap 1
40 P1011100 -BF Snatch Block - Black
Flat 1
41 P101120 0 -BF Speed Mount™ Hitch
Adapter - Black Flat 1
42 811000-BF Roller Fairlead - Black
Flat 1
43 P1011019 1.8 m (6 ft.) Cable
with Quick Connect 1
44 C10038 9.5 mm (3/8 in.)
Clevis Hook 1
45 810033 Motor Coupling 1
46 P1011033 Hexagonal Shaft I 1
47 P1011034 Hexagonal Shaft II 1
48 810035 Retainer-Ring 50 1

13 REV 11051-20131115
ENGLISH 11051
TROUBLESHOOTING
Problem Cause Solution
Motor does not turn on Switch Assembly not connected
properly
Insert Switch Assembly all the way into the connector
Loose battery cable connections Tighten nuts on all cable connections
Contactor malfunctioning Tap contactor to loosen contacts. Apply 12 volts to
coil terminals directly. A clicking indicates proper
activation
Defective Switch Assembly Replace Switch Assembly
Defective motor Check for voltage at armature port with Switch
pressed. If voltage is present, Replace motor
Water has entered motor Allow to drain and dry. Run in short bursts without
load until completely dry
Motor runs but Cable
drum does not turn
Clutch (Cam Ring) not engaged Move Cam Ring to the "In" position. If problem
persists, a qualified technician needs to check and
repair
Motor runs slowly or
without normal power
Insufficient current or voltage The battery is weak, recharge. Run winch with vehicle
motor running (battery should have a strong charge)
Loose or corroded battery cable
connections.
Clean, tighten, or replace
Motor overheating winch running time too long Allow winch to cool down periodically
Motor runs in one
direction only
Defective or stuck Contactor Tap Contactor to loosen contacts
Repair or Replace contactor
Defective Switch Assembly Replace Switch Assembly
For further technical support:
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
[e-mail]

REV 11051-20131115 14
11051 ENGLISH
WARRANTY
WARRANTY
CHAMPION POWER EQUIPMENT
2 YEAR LIMITED WARRANTY
Effective September 1, 2006. Replaces all undated
warranties and all warranties dated before September 1,
2006.
Warranty Qualifications
Champion Power Equipment (CPE) will register this
warranty upon receipt of your Warranty Registration Card
and a copy of your sales receipt from one of CPE’s retail
locations as proof of purchase.
Please submit your warranty registration and your proof of
purchase within ten (10) days of the date of purchase.
Repair/Replacement Warranty
CPE warrants to the original purchaser that the
mechanical and electrical components will be free of
defects in material and workmanship for a period of
one year (parts and labor) and two years (parts) from
the original date of purchase (90 days (parts and labor)
and 180 days (parts) for commercial & industrial
use). Transportation charges on product submitted for
repair or replacement under this warranty are the sole
responsibility of the purchaser. This warranty only applies
to the original purchaser and is not transferable.
Do Not Return The Unit
To The Place Of Purchase
Contact CPE’s Technical Service and CPE will
troubleshoot any issue via phone or e- mail. If the
problem is not corrected by this method, CPE will, at its
option, authorize evaluation, repair or replacement of the
defective part or component at a CPE Service Center.
CPE will provide you with a case number for warranty
service. Please keep it for future reference. Repairs
or replacements without prior authorization, or at an
unauthorized repair facility, will not be covered by this
warranty.
Warranty Exclusions
This warranty does not cover the following repairs and
equipment:
Normal Wear
Winches need periodic parts and service to perform well.
This warranty does not cover repair when normal use has
exhausted the life of a part or the equipment as a whole.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labor if this
winch is deemed to have been misused, neglected,
involved in an accident, abused, loaded beyond the
winch’s limits, modified, installed improperly or
connected incorrectly to any electrical component.
Normal maintenance is not covered by this warranty.
Other Exclusions
This warranty excludes: The winch cable. Cosmetic
defects such as paint, decals, etc. Accessory parts such
as storage covers. Failures due to acts of God and other
force majeure events beyond the manufacturer’s control.
Problems cause by parts that are not original Champion
Power Equipment parts.
Limits of Implied Warranty and
Consequential Damage
Champion Power Equipment disclaims any obligation to
cover any loss of time, use of this product, freight, or any
incidental or consequential claim by anyone from using
this winch. THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE
A unit provided as an exchange will be subject to the
warranty of the original unit. The length of the warranty
governing the exchanged unit will remain calculated by
reference to the purchase date of the original unit.
This warranty gives you certain legal rights which may
change from province to province. Your province may also
have other rights you may be entitled to that are not listed
within this warranty.
Contact Information
Address
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Rd.
Santa Fe Springs, CA 90670
www.championpowerequipment.com
Customer Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
[e-mail]
Fax no.: 1-562-236-9429
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
[e-mail]
24/7 Tech Support: 1-562-204-1188