Champion Phlebotomy Sprit BDC Operation manual

OWNER'S OPERATING AND MAINTENANCE MANUAL
1-800-237-3377
CHAMPIONCHAIR.COM
Phlebotomy Collection
Document No. 006020 Rev R
Spirit BDC
(2570/2571)
Shown: 2570
Solace BDC
(2572/2573)
Shown: 2572
Unity BDC
(2574/2575)
Shown: 2574

Page 2 of 30
manual
Document No.: 006020 - Revision: R
IMPORTANT
READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE US-
ING THIS PRODUCT!
Do NOT install, maintain or operate this equipment without reading and following this manual,
otherwise injury and/or damage may result.
IF YOU HAVE ANY QUESTIONS OR CONCERNS, PLEASE CONTACT CHAMPION MANUFACTURING,
INC .
Champion assumes no responsibility for damage or injury caused by improper assembly, instal-
lation, use, or maintenance of these products.
No part of this manual may be duplicated in any form without the prior consent of Champion
Manufacturing, Inc . Unauthorized duplication/distribution of these materials may result in civil
prosecution to the maximum extent allowed by law.
The information contained in this manual is subject to change without notice.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE!
These instructions are available online at no charge.
Visit ChampionChair.com to download.

Page 3 of 30
manual
Document No.: 006020 - Revision: R
TABLE OF CONTENTS
Important Safety Information..................................................................................................... 6
Intended Use Statement.............................................................................................................. 5
Transportation, Storage, Handling & Disposal Instructions.................................................. 5
GENERAL CARE & CLEANING....................................................................................................... 6
Tools Required............................................................................................................................... 7
SPIRIT BDC: MODEL 2570/2571 .................................................................................................. 8
Glide Foot Installation............................................................................................................. 8
Seat Installation ....................................................................................................................... 9
Arm Assembly and Installation ............................................................................................. 10
Urethane Flip-Up Arm Level Adjustments .......................................................................... 11
Cabinet Assembly and Installation....................................................................................... 12
Removing and Re-Installing Cabinet Drawer ..................................................................... 13
Pivot Arm Pivot-Point Adjustment........................................................................................ 14
SOLACE BDC: MODEL 2572/2573 ............................................................................................... 15
Glide Foot Installation............................................................................................................. 15
Seat Installation ....................................................................................................................... 16
Arm Assembly and Installation ............................................................................................. 17
Urethane Flip-Up Arm Level Adjustments .......................................................................... 18
Cabinet Assembly and Installation....................................................................................... 19
Removing and Re-Installing Cabinet Drawer ..................................................................... 20
Pivot Arm Pivot-Point Adjustment........................................................................................ 21
Unity BDC: MODEL 2574/2575 .................................................................................................... 22
Glide Foot Installation............................................................................................................. 22
Seat Installation ....................................................................................................................... 23
Arm Assembly and Installation ............................................................................................. 24
Urethane Flip-Up Arm Level Adjustments .......................................................................... 25
Cabinet Assembly and Installation....................................................................................... 26
Removing and Re-Installing Cabinet Drawer ..................................................................... 27
Pivot Arm Pivot-Point Adjustment........................................................................................ 28

Page 4 of 30
manual
Document No.: 006020 - Revision: R
IMPORTANT SAFETY INFORMATION
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING PRODUCT.
1. Chair should ALWAYS be positioned on a secure, level surface.
2. Children MUST be supervised at all times when seated in or when near the chair.
3. DO NOT stand on chair.
4. DO NOT use movable arm as a restraint device.
5. DO NOT put hands, feet or clothing into any openings when changing chair or accessory positions. Attendant
MUST confirm that users arms, legs, hands and feet are safe while changing chair and/or accessory positions
or SERIOUS INJURY MAY RESULT.
6. STAY CLEAR of moving parts.
7. DO NOT use chair for transporting in or with ANY type of vehicle or trailer. Champion chairs have not been
tested or approved for use by an occupant in any type of vehicle or trailer.
8. NEVER sit on chair arms or backrest; SERIOUS INJURY or damage may occur.
9. Failure to completely tighten the seat mounting screws or any fasteners on chair COULD RESULT IN INJURY.
10. Periodically check the tightness of all nuts, bolts and screws.
11. Immediately REMOVE FROM SERVICE; Any chair with broken parts, torn upholstery, or other mechanical or
visible damage.
12. USE ONLY Champion AUTHORIZED REPLACEMENT PARTS or ATTACHMENTS.
13. NEVER EXCEED the recommended weight capacity. ALWAYS refer to the weight capacity label on your chair.
In all cases the labeling on the chair at the time of delivery indicates the correct rating for your chair.
14. Flip-up arms are NOT intended to restrain patients or support patient weight.
15. NEVER leave patients unattended.
16. SAVE THESE INSTRUCTIONS for future reference and training.
WARNING

Page 5 of 30
manual
Document No.: 006020 - Revision: R
INTENDED USE STATEMENT
The Champion Blood Drawing Chair is a chair intended for use in medical settings. It is designed without wheels
and is not electrically powered. It is intended for use in blood donation, collection, or sampling procedures.
TRANSPORTATION, STORAGE, HANDLING & DISPOSAL
• The product should be transported in factory packaging, inside an appropriate medium for the
destination, i.e., air/sea cargo containers.
• The product should be stored in an environment that will inhibit rust/mold formation.
• Champion Manufacturing, Inc recommends not leaving the product in the factory packing in excess of
three (3) months.
• The product should always be handled in a manner consistent with the user instructions and in a
manner to prevent contamination after each use.
• The product has many recyclable components and to the extent practical, all effort should be used to
recycle responsibly. Otherwise the product components shall be disposed of in accordance with local
statutes.

Page 6 of 30
manual
Document No.: 006020 - Revision: R
GENERAL CARE & CLEANING
• Periodically inspect tightness of all screws, bolts, nuts, or other fasteners.
Champion Manufacturing, Inc’s full-line of products are built to provide durability and reliability when properly
cared for. In general all of our products should be:
1. Cleaned
2. Disinfected (per facility policy)
3. Rinsed
4. Allowed to air dry
It is important to note that disinfecting a product is not the same as cleaning the product. Disinfectants alone
will not provide adequate cleaning, they do not have grease or oil cutting properties to remove grime or hair and
skin oils. Over time, the appearance and feel and performance of your upholstery may diminish if not cleaned
properly.
CLEANING
Remove grime, hair and body oils; Your furnishings should be cleaned with mild soap & water solution and
a damp cloth on a regular basis (especially where skin & hair make contact with upholstery). Avoid harsh
detergents or chemicals that could damage the upholstery or finish of your chair. If the furnishing’s upholstery
is disinfected with chemicals or bleach mixtures, the chair MUST be wiped o using only clean water on a damp
cloth and then be allowed to air dry. Failure to rinse upholstery with clean water can result in a build-up of
residues over time that can dry out the upholstery and cause changes to the look and feel of the upholstery and
eventually can lead to cracking.
Please refer to any instruction labels or tags that may have been included with your product for complete care
and cleaning instructions. Retain information on the label or tag for future use.
For additional cleaning information, please visit www.championchair.com/cleaning-instructions/
For Custom Vinyl, please refer to the manufacturer’s instructions.

Page 7 of 30
manual
Document No.: 006020 - Revision: R
TOOLS REQUIRED
MODELS 2570, 2571, 2572, 2573, 2574 AND 2575
• Multiple size wrench included (or suitable , ” & ” or adjustable wrenches)
• Phillips-head screwdriver
• Scissors or box cutter
• Powered tools not recommended
PREPARATION: BEFORE YOU BEGIN
1. Carefully examine your product for any damage. Be sure to inspect all components.
IF DAMAGE IS EVIDENT, CONTACT FREIGHT CARRIER OR CHAMPION IMMEDIATELY.
2. Remove all packaging material and any hardware that was secured for shipping.
3. Carefully remove all components and any included tools and/or parts from the carton.
4. You may need to cut packaging materials with a box cutter or scissors to access the product. Use CAUTION
to avoid personal injury or damage to the product.
5. Save all boxes and packaging material until AFTER you have assembled your product and have verified that
all components are functioning properly. These material are required if it becomes necessary to return the
product.
6. DO NOT install, maintain or operate this equipment without reading and following this manual otherwise
injury and/or damage may result. IF YOU HAVE QUESTIONS OR CONCERNS PLEASE CONTACT Champion
Manufacturing, Inc .
CHAMPION ASSUMES NO RESPONSIBILITY FOR DAMAGE OR INJURY CAUSED BY IMPROPER ASSEMBLY,
INSTALLATION, USE, OR MAINTENANCE OF THESE PRODUCTS.

Page 8 of 30
manual
Document No.: 006020 - Revision: R
SPIRIT BDC: MODEL 2570/2571
GLIDE FOOT INSTALLATION
1. Place chair on side and install four (4) Glide Feet in threaded holes on the bottom of the Chair Frame (FIG.
1 & 2).
2. Li and position the chair to the upright position, with Glide Feet on a level floor.
3. If the Chair Frame does not sit level on the floor, loosen select Glide Feet individually as needed to achieve
stable, level positioning of the chair.
4. Continue adjusting until the Chair Frame is level and stable.
SHOWN: Model 2570 Spirit BDC
with Cabinet
SHOWN: Model 2571 Spirit BDC
with Standard Arm
FIG. 1
x4
FIG. 2
x4

Page 9 of 30
manual
Document No.: 006020 - Revision: R
SEAT INSTALLATION
Failure to completely tighten the seat mounting screws COULD RESULT IN SERIOUS
INJURY.
1. Position Chair Frame in upright position. Check tightness of all installed screws, bolts, nuts and other
fasteners in case they loosened during shipping.
2. Align the mounting holes on the plastic Seat with the Seat Support holes. Hole spacing of Seat and Seat
Supports will be narrower toward front of chair. Seat can only be installed facing one direction (FIG. 1).
3. Using the included wrench (or your own ” tool), install the four (4) included Seat Screws through the
holes of Chair Frame, and into the four (4) holes on bottom of the plastic Seat. Make sure screws are
completely tightened (FIG. 1).
NOTE: These “special” screws MUST BE USED for maximum grip in this seating application. They can be
slightly diicult to “get started” in the holes on the plastic Seat.
TIP: Use even pressure and, if available, a “” nut-driver” (screwdriver-type handle with a ” socket on end)
however, this task can be accomplished with the included wrench.
WARNING
FIG. 1

Page 10 of 30
manual
Document No.: 006020 - Revision: R
ARM ASSEMBLY AND INSTALLATION
1. If the Arm Assembly has not yet been installed, insert it into the Receiving Tube on the Seat Frame
Assembly (FIG. 1). This applies to any style arm assembly.
• ALWAYS make sure that the slot in the Arm Assembly faces the Knob installed on the receiving tube
(FIG. 1).
2. Then adjust the arm to the desired height and tighten the knob. Screw the Knob into the Slot. This will
“capture” the arm and keep it from being able to be pulled out of the frame accidentally.
IMPORTANT: DO NOT OVER-TIGHTEN. The Knob will NOT need to be extremely tight to eectively hold
arms in position.
FIG. 1

Page 11 of 30
manual
Document No.: 006020 - Revision: R
URETHANE FLIP-UP ARM LEVEL ADJUSTMENTS
Use a ⅛” Hex Key to make minor leveling adjustments to the Urethane Flip-Up Armrest as needed.
1. Rest the Hinge Plate flat on the Hinge Arm Support Bracket.
2. Insert the ⅛” Hex Key into the underlying access hole as shown and turn the screw located inside clockwise
until the screw is firmly pressed against the Arm’s Hinge Plate (FIG. 1).
FIG. 1

Page 12 of 30
manual
Document No.: 006020 - Revision: R
CABINET ASSEMBLY AND INSTALLATION
* MODEL 2570
1. Remove the cabinet from the frame (FIG. 1). Use CAUTION to avoid personal injury or damaging the
product.
2. Remove packaging materials from cabinet assembly.
3. The cabinet installs on the PATIENT LEFT side of chair (FIG. 2). Insert the cabinet assembly into the receiving
tube. ALWAYS make sure that the slot in the Arm Assembly faces the knob installed on the receiving tube
(FIG. 2).
4. Adjust the Cabinet to the desired height and tighten knob.
5. Cabinet installation is complete (FIG. 3). Be sure to tighten the BLACK KNOB to secure the cabinet even if
no height adjustment is made. This will ensure cabinet is secure for use.
FIG. 2
FIG. 3
FIG. 1

Page 13 of 30
manual
Document No.: 006020 - Revision: R
REMOVING AND RE-INSTALLING CABINET DRAWER
* MODEL 2570
1. To remove drawer, open drawer until the drawer stops. Using your finger, locate the drawer stop tab
mounted to the bottom of the drawer top. Press the tab against the drawer top and slide the drawer past the
tab (FIG. 1).
2. To reinstall the drawer, insert the rear part of the drawer past the drawer stop, then slide the drawer into the
frame (FIG. 2). Bin dividers can be installed into the grooves as needed (FIG. 2).
FIG. 2
FIG. 1

Page 14 of 30
manual
Document No.: 006020 - Revision: R
PIVOT ARM PIVOT-POINT ADJUSTMENT
Your Pivot Arm Assembly may be configured in one of two (2)
directions:
• Pivot point located near the back of the chair. This will
provide arm support that is straight or at a slight angle
to the side of the patient (standard position) (FIG. A).
• Pivot point located near front of chair. This will provide
arm support across the front of the patient’s body.
1. If you wish to change the standard setup of the Pivot Arm
(FIG. 1) so that the pivot point is toward the front of the
chair, proceed to the next step. Otherwise, skip this step. If
you ordered Dual Pivot Arms, you can choose which Arm(s),
if any, you wish to alter. This change may be made before or
aer Arm Assembly is installed on the chair.
2. Use a Phillips or #2 square bit screwdriver to remove the
four (4) wood screws on the underside of the arm assembly
that hold the pivot arm assembly onto the steel arm support.
3. Aer removing the four (4) wood screws, rotate the steel arm support 180° (FIG. 2).
4. Reinstall the four (4) wood screws to secure the arm support in the new position (FIG. 3).
FIG. 1 FIG. 2 FIG. 3

Page 15 of 30
manual
Document No.: 006020 - Revision: R
SOLACE BDC: MODEL 2572/2573
GLIDE FOOT INSTALLATION
1. Place chair on side and install four (4) Glide Feet in threaded holes on the bottom of the Chair Frame (FIG.
1 & 2).
2. Li and position the chair to the upright position, with Glide Feet on a level floor.
3. If the Chair Frame does not sit level on the floor, loosen select Glide Feet individually as needed to achieve
stable, level positioning of the chair.
4. Continue adjusting until the Chair Frame is level and stable.
SHOWN: Model 2572 Solace BDC with
Cabinet
SHOWN: Model 2573 Solace BDC
with Standard Arm
FIG. 1
x4
FIG. 2
x4

Page 16 of 30
manual
Document No.: 006020 - Revision: R
SEAT INSTALLATION
Failure to completely tighten the seat mounting screws COULD RESULT IN SERIOUS
INJURY.
1. Position Chair Frame in upright position. Check tightness of all installed screws, bolts, nuts and other
fasteners in case they loosened during shipping.
2. Align the screws on bottom of the Seat Assembly, with the Seat Support holes. (Hole spacing of Seat
Supports will be narrower toward front of Chair). Seat can only be properly installed facing one direction. Be
sure that all four (4) Seat Screws go completely through the Seat Support straps on chair frame (FIG.
1).
3. Install four (4) lock nuts to the screws on the Seat Assembly and completely tighten with ” wrench (FIG.
1).
WARNING
FIG. 1

Page 17 of 30
manual
Document No.: 006020 - Revision: R
ARM ASSEMBLY AND INSTALLATION
1. If the Arm Assembly has not yet been installed, insert it into the Receiving Tube on the Seat Frame
Assembly (FIG. 1). This applies to any style arm assembly.
• ALWAYS make sure that the slot in the Arm Assembly faces the Knob installed on the receiving tube
(FIG. 1).
2. Then adjust the arm to the desired height and tighten the knob. Screw the Knob into the Slot. This will
“capture” the arm and keep it from being able to be pulled out of the frame accidentally.
IMPORTANT: DO NOT OVER-TIGHTEN. The Knob will NOT need to be extremely tight to eectively hold
arms in position.
FIG. 1

Page 18 of 30
manual
Document No.: 006020 - Revision: R
URETHANE FLIP-UP ARM LEVEL ADJUSTMENTS
Use a ⅛” Hex Key to make minor leveling adjustments to the Urethane Flip-Up Armrest as needed.
1. Rest the Hinge Plate flat on the Hinge Arm Support Bracket.
2. Insert the ⅛” Hex Key into the underlying access hole as shown and turn the screw located inside clockwise
until the screw is firmly pressed against the Arm’s Hinge Plate (FIG. 1).

Page 19 of 30
manual
Document No.: 006020 - Revision: R
CABINET ASSEMBLY AND INSTALLATION
* MODEL 2572
1. Remove the cabinet from the frame (FIG. 1). Use CAUTION to avoid personal injury or damaging the
product.
2. Remove packaging materials from cabinet assembly.
3. The cabinet installs on the PATIENT LEFT side of chair (FIG. 2). Insert the cabinet assembly into the receiving
tube. ALWAYS make sure that the slot in the Arm Assembly faces the knob installed on the receiving tube
(FIG. 2).
4. Adjust the Cabinet to the desired height and tighten knob.
5. Cabinet installation is complete (FIG. 3). Be sure to tighten the BLACK KNOB to secure the cabinet even if
no height adjustment is made. This will ensure cabinet is secure for use.
FIG. 2
FIG. 3
FIG. 1

Page 20 of 30
manual
Document No.: 006020 - Revision: R
REMOVING AND RE-INSTALLING CABINET DRAWER
* MODEL 2572
1. To remove drawer, open drawer until the drawer stops. Using your finger, locate the drawer stop tab
mounted to the bottom of the drawer top. Press the tab against the drawer top and slide the drawer past the
tab (FIG. 1).
2. To reinstall the drawer, insert the rear part of the drawer past the drawer stop, then slide the drawer into the
frame (FIG. 2). Bin dividers can be installed into the grooves as needed (FIG. 2).
FIG. 2
FIG. 1