Char-Griller 1414 User manual

OM1414 A.3 ™ & © Char-Griller / A&J Mfg.
OWNER’S MANUAL
Model # 1414
3-in-1
Charcoal Grill
Keep your receipt with this manual for Warranty.
Grill with Full Cart – Page 3
Portable Grill - Page 18
Side Fire Box - Page 12

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 2
STOP! CALL FIRST! DO NOT
RETURN PRODUCT TO STORE.
CALL [phone] This product has been built to the highest quality standards.
Call us should you have any questions not addressed in these instructions, or for
service information.
No Returns on Used Grills
PARTS LIST AND TOOLS REQUIRED
(Tools Not Included)
Pliers and 7/16" nut driver
Parts Bag Contains:
“U” handle Bolt
1pc
Damper Circle
2pcs
Lock
Bracket
1 pcs
8pcs
1 1/2” Hex Bolt
Lock
Washer
15 pcs
2 pcs
Push on Wheel
Caps Washer
1/4”
5 pcs
1/2” Hex Bolt
15 Pcs 35 pcs
Hex Nut
1/4”
Have your grills serial number (located on the back of the grill body or on the leg)
when calling.
# QTY Part Name Part #
1 1 SIDE SHELF 20-0114
2 1 HOOD HANDLE 55-0017
3 1 GRILL BODY 20-0166
4 1 WIRE HANDLE 55-0016
5 1 FIRE GRATE 20-0028
6 1 U HANDLE 55-0004
7 2 DAMPER CIRCLE 10-0036
8 1 ASH DRAWER 20-0100
9 2 LEG BRACE 10-0175
10 1 WIRE RACK 20-0103
11 2 WHEEL 55-0026
12 2 HUB CAP 55-0007
13 2 SHORT LEG 20-0106
14 2 LONG LEG 10-0174
15 2 LEG CROSS BAR 10-0173
16 1 DRAWER LATCH 10-0172
17 2 COOKING GRATE 10-0086
1
2
3 4
5
6
7
7
8
9
9
10
11
12
13
14
15
16
17
1 3/4” Hex Bolt
8 Pcs

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 6
Step 5. Attach the WHEEL to the spindle coming out of the SHORT LEGS. Install
one WASHER, COTTER PIN and HUB CAP onto the spindle after the WHEEL.
Repeat this on the opposite SHORT LEG.
Axle
Wheel
Washer
Cotter Pin
Hub Cap
Short Leg
Step 6: Attach the GRILL BODY to the Cart/Leg Assembly (Make sure that the damper
is on the same side as the wheels) with four 1 3/4” Hex Bolts.
Hex Bolts
(4) 1 3/4” Hex Bolts
(4)Hex Nuts
Hex Nuts
Grill Body
Cart/Leg Assembly
Damper
(2) Axel Cap
(2) Cotter Pin
(2) Flat Washer

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 7
Step 7: Attach WOOD HANDLE with two 1/2” HEX BOLTS, two LOCK WASHERS,
and two HEX NUTS.
(2) 1/2” Hex Bolts
(2)Hex Nuts
(2)Lock Washers
Wood Handle
Hex Bolts
Lock Washers
Hex Nuts
Step 8: Attach WIRE HANDLE to the right side of GRILL BODY with two 1/2” HEX
BOLTS, two LOCK WASHERS, and two HEX NUTS.
(2) 1/2” Hex Bolts
(2)Hex Nuts
(2)Lock Washers
Hex Bolts
WIRE HANDLE
Lock Washers
Hex Nuts
Grill Body

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 8
Step 9: Attach DRAWER LATCH to GRILL BODY right side with 1/2” HEX BOLT and
HEX NUT.
(1) 1/2” Hex Bolts
(1)Hex Nuts
Step 10: Attach SIDE SHELF to left side of Grill BODY with four 1/2” HEX BOLTS
and four HEX NUTS.
(4) 1/2” Hex Bolts
(4)Hex Nuts
Side Shelf Grill Body
Hex Bolts
Hex Nuts
Grill Body
Hex Nut
Hex Bolt
Drawer Latch

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 9
Step 11: Attach DAMPER CIRCLE to the ASH DRAWER with 1/2” HEX BOLT, FLAT
WASHER, LOCK WASHER, and HEX NUT, see below.
(1) 1/2” Hex Bolt
(1)Hex Nut (1)Lock Washer
(1)Flat Washer
Hex Bolt
Ash Drawer
Damper Circle
Flat Washer
Hex Nut
Lock Nut
Step 12: Attach U HANDLE to ASH DRAWER with two LOCK WASHERS and two
HEX NUTS.
(2)Lock Washers
(2)Hex Nuts
U Handle
Ash Drawer
Lock Washers
Hex Nuts

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 10
Step 13: Attach DAMPER CIRLE to GRILL BODY with HEX BOLT, FLAT WASHER,
LOCK WASHER, and HEX NUT, see below.
(1) 1/2” Hex Bolt
(1)Hex Nut (1)Lock Washer
(1)Flat Washer
Grill Body
Hex Bolt
Damper Circle
Flat Washer
Lock Washer
Hex Nut
Step 14: Tighten ALL BOLTS and NUTS. Insert a 1/2” BOLT and tighten with a NUT
for any open holes in Grill BODY after assembly.

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 11
Step 15: Place FIRE GRATE onto ASH DRAWER then slides it into GRILL BODY.
Ash Drawer
Grill Body
Fire Grate
Step 16: Place COOKING GRATE into GRILL BODY.
Cooking Grates
Grill Body
NO RETURNS ON USED GRILLS.

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 12
STOP! CALL CHAR GRILLER FIRST! DO NOT RETURN PRODUCT TO
THE STORE.
CALL Char Griller [phone] This product has been built to the highest quality
standards. Call us should you have any questions not addressed in these instruc-
tions, or for service information.
No Returns
on Used
Grills
(Tools Not Included)
Pliers 7/16" nut driver
Parts List::
1 Cooking Chamber
2 Damper Circle
2 Cast Iron Grates
2 Metal rod handle
1 Wood handle
1 Wire rack (for wood)
1 Side Drawer / Ash pan / Fire grate
1 Cast Iron Lifter
1 Lock Bracket
Phillips Head Screwdriver
Have your grills serial number (located on the back of the grill body or on the leg)
when calling.
PARTS LIST AND TOOLS REQUIRED
SIDE FIRE BOX

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 13
ASSEMBLY INSTRUCTIONS– SIDE FIRE BOX
Read all safety warnings and instructions carefully before
assembling and operating your grill.
IMPORTANT HINT: DO NOT TIGHTEN ANY NUTS AND BOLTS UNTIL
GRILL IS FULLY ASSEMBLED.
Remove and unwrap the grill and all of its parts from the packaging. Remove the
Cooking Grates, Warming Rack, Ash Pan, and Side Damper from the Main Grill
Body.
Step 1: Remove the FILLER PLATES from the SFB and main GRILL BODY that you
plan to install the SFB onto.
Grill Body
SFB
Filler Plates
Step 2: Attach SFB to main GRILL BODY. With a helper align the SFB in place over the
opening on the grill body then attach with six 1/2” BOLTS and NUTS.
(6) 1/2” Hex Bolts
(6)Hex Nuts
Grill Body
SFB
Hex Bolts
Hex Nuts

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 14
Step 3: Attach SPACER TUBES in between SFB and side braces and secure with two 2”
HEX BOLTS and HEX NUTS. The HEX BOLTS should go through from the SFB side,
see below. Align the SPACER TUBES with the corresponding holes on the leg brace and
SFB. Insert the 2” HEX BOLT through the SFB then through the SPACER TUBE , and
finally through the leg brace. Then secure the HEX BOLT with the HEX NUT.
(2)Hex Nuts
Hex Nuts
Step 4: Attach the WIRE HANDLE to the SFB right side with two 1/2” HEX BOLTS,
two LOCK WASHERS, and two HEX NUTS, see below.
(2) 1/2” Hex Bolts
(2)Hex Nuts
(2)Lock Washer
Hex Bolts
Hex Nuts
Lock Washers
SFB
Wire Handle
Side Brace
SFB
(2) 2” Hex Bolts
(2) Spacer Tubes
Hex Bolts
Spacer Tube

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 15
Step 6: Attach WOOD HANDLE to SFB HOOD with two 1/2” HEX BOLTS, two LOCK
WASHERS, and two HEX NUTS.
(2) 1/2” Hex Bolts
(2)Hex Nuts
(2)Lock Washers
Wood Handle
Hex Bolts
Lock Washers
Hex Nuts
Step 5: Attach DRAWER LATCH to GRILL BODY right side with 1/2” HEX BOLT and
HEX NUT.
(1)Hex Nut
(1) 1/2” Hex Bolt
Grill Body
Hex Bolt
Hex Nut
Drawer Latch

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 16
Step 8: Attach U HANDLE to ASH DRAWER with two LOCK WASHERS and two
HEX NUTS.
(2)Lock Washers
(2)Hex Nuts
U Handle
Ash Drawer
Lock Washers
Hex Nuts
Step 8: Tighten ALL BOLTS and NUTS. Insert a 1/2” BOLT and tighten with a NUT for
any open holes in Grill BODY after assembly.
Step 7: Attach DAMPER CIRCLE to the ASH DRAWER with 1/2” HEX BOLT, FLAT
WASHER, LOCK WASHER, and HEX NUT, see below.
(1) 1/2” Hex Bolt
(1)Hex Nut
(1)Lock Washer
(1)Flat Washer
Hex Bolt
Ash Drawer
Damper Circle
Flat WasherHex Nut
Lock Nut

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 17
Step 10: Place FIRE GRATE onto ASH DRAWER then slides it into SFB.
NO RETURNS ON USED GRILLS.
Step 11: Place COOKING GRATE onto SFB.
Ash Drawer
SFB
Fire Grate
SFB
Cooking Grates

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 18
STOP! CALL Char Griller FIRST! DO NOT RETURN PRODUCT TO STORE
CALL Char Griller [phone] This product has been built to the highest quality
standards. Call us should you have any questions not addressed in these instruc-
tions, or for service information.
No Returns on
Used Grills
PARTS LIST AND TOOLS REQUIRED
PORTABLE GRILL
(Tools Not Included)
Pliers 7/16" nut driver
Parts List::
1 Cooking Chamber
2 Legs
2 Damper Circle
2 Cast Iron Grates
2 Metal rod handles
1 Wood handle
1 Wire rack (for wood)
1 Side Drawer / Ash pan / Fire grate
1 Cast Iron Lifter
1 Lock Bracket
Phillips Head Screwdriver
Have your grills serial number (located on the back of the grill body or on the leg)
when calling.

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 19
ASSEMBLY INSTRUCTIONS– PORTABLE GRILL
Read all safety warnings and instructions carefully before
assembling and operating your grill.
IMPORTANT HINT: DO NOT TIGHTEN ANY NUTS AND BOLTS UNTIL
GRILL IS FULLY ASSEMBLED.
Note: All nuts go on the inside of the grill.
Remove and unwrap the grill and all of its parts from the packaging.
Step 1: Attach LEGS to GRILL BODY with four 1/2” HEX BOLTS and four HEX
NUTS, see below.
(4) 1/2” Hex Bolts
(4)Hex Nuts
Hex Bolts
Legs
Hex Nuts
Grill Body

OM1414 A.3 ™ & © Char-Griller / A&J Mfg. 20
Step 2: Attach WOOD HANDLE to GRILL HOOD with two HEX BOLTS, two LOCK
WASHERS, and two HEX NUTS, see below.
(2) 1/2” Hex Bolts
(2)Hex Nuts
Wood Handle
Grill Hood
Hex Bolts
Hex Nuts
Lock Washers
(2)Lock Washers
Step 3: Attach WIRE HANDLE to GRILL BODY with four HEX BOLTS and four HEX
NUTS, see below.
(4) 1/2” Hex Bolts
(4)Hex Nuts
Hex Bolts
Hex Bolts
Wire Handle
Wire Handle
Hex Nuts