Chattanooga Adapta ADP400 User manual

User Manual
ADP400 Traction Table
Moving
Rehabilitation
Forward™
ADAPTA®

FOREWORD ......................................1
Product Description .............................................. 1
ABOUT ADAPTA ADP400 TABLE .................24
Precautionary Instructions ....................................... 2
Cautions ........................................................ 3
Warnings ...................................................... 3-4
Dangers ......................................................... 4
NOMENCLATURE .................................5
Table Familiarization ............................................. 5
TECHNICAL SPECIFICATIONS ...................611
Specications ................................................... 6
Table Dimensions ................................................ 7
Cushion Dimensions ............................................. 8
Electromagnetic Compatibility Tables..........................9-11
SETUP........................................1214
Contents of Crate ...............................................12
Glide Leveler Adjustments ......................................12
Attaching Traction Unit Stand to Table ...........................13
Mounting Traction Unit to Stand .................................14
OPERATION ..................................1517
Adjusting Table Sections .....................................15-16
Table Height Adjustment........................................16
Relocating the Table (with Optional Retractable Caster)...........17
MAINTENANCE ..................................18
Cleaning .......................................................18
Service .........................................................18
Warranty Repair/Out of Warranty Repair .........................18
WARRANTY .....................................19
TABLE OF CONTENTS Adapta® ADP400

1
This manual has been written for the owners and operators of the Adapta ADP400 traction table. It contains general instructions for
operation, precautionary instructions, and maintenance recommendations. In order to obtain maximum life and efficiency from your
Adapta ADP400 traction table, and to assist in the proper operation of the unit, read and understand this manual thoroughly.
The specifications put forth in this manual were in effect at the time of the publication. However, owing to DJO, LLC’s policy of
continuous improvement, changes to these specifications may be made at any time without obligation on the part of DJO, LLC.
Before administering any treatment to a patient, you should become acquainted with the operating procedures, as well as the
warnings, and precautions.
Product Description
The Adapta ADP400 offers state-of-the-art traction technology. With its outstanding design features, stability and ease-of-operation,
the Adapta ADP400 traction table is the perfect complement to Triton, TX or Tru-Trac traction units. The adjustable head and lumbar
sections also adapt to all common treatment positions allowing the ADP400 to double as a treatment table. The Adapta ADP400
features the following: an electric hand control high-low adjustment, a full working surface, and a lumbar section that separates to
eliminate friction during lumbar traction.
This equipment is to be used only under the prescription and supervision of a licensed practitioner.
© 2010 DJO, LLC Vista, California, USA. Any use of editorial, pictorial, or layout composition of this publication without express written consent from DJO, LLC is strictly prohibited. This
publication was written, illustrated, and prepared for distribution by DJO, LLC.
FOREWORD Adapta® ADP400

2
The precautionary instructions found in this section and throughout
this manual are indicated by specific symbols. Understand these
symbols and their definitions before operating this equipment. The
definitions of these symbols are as follows:
Caution -
Text with a “CAUTION” indicator will explain possible safety infractions
that could have the potential to cause minor to moderate injury or
damage to equipment.
Warning -
Text with a “WARNING” indicator will explain possible safety infractions
that will potentially cause serious injury and equipment damage.
Danger -
Text with a “DANGER” indicator will explain possible safety infractions
that are imminently hazardous situations that would result in death or
serious injury.
NOTE:
Throughout this manual “NOTE”may be found. These Notes are helpful
information to aid in the particular area or function being described.
PRECAUTIONARY INSTRUCTIONS
ABOUT ADAPTA ADP400 TABLE Adapta® ADP400

3
Read, understand, and practice the precautionary and operating•
instructions found in this manual. Know the limitations and
hazards associated with your treatment table. Observe any and all
precautionary and operational decals placed on the unit.
DO NOT operate this table in an environment where other•
devices are being used that intentionally radiate electromagnetic
energy in an unshielded manner. Portable and mobile RF
communications equipment can affect Medical Electrical
Equipment.
This table generates, uses, and can radiate radio frequency energy•
and, if not installed and used in accordance with the instructions,
may cause harmful interference to other devices in the vicinity.
However, there is no guarantee that interference will not occur
in a particular installation. Harmful interference to other devices
can be determined by turning this table on and off. Try to correct
the interference using one or more of the following: reorient or
relocate the receiving device, increase the separation between
the equipment, connect the table to an outlet on a different
circuit from that which the other device(s) are connected and
consult the DJO, LLC Service Department for help.
Keep table out of high moisture environments.•
This table should be operated, transported, and stored in•
temperatures between 0° F (-18° C) and 140° F (60° C), with
relative humidity ranging from 30% - 80%.
Do not exceed table weight capacity of 400 lbs (182 kg).•
ABOUT ADAPTA ADP400 TABLE
U.S. federal law restricts this device to sale by, or on the order of, a•
licensed practitioner.
Make certain that the table is electrically grounded by connecting•
only to a grounded electrical service receptacle conforming to the
applicable national and local electrical codes.
Care must be taken when operating this equipment adjacent to or•
stacked with other equipment. Potential electromagnetic or other
interference could occur to this or other equipment. Try to minimize
this interference by not using other equipment in conjunction with
it.
Do not leave the table unlocked and unattended at any time.•
Never place your hands and feet near the working mechanism of•
the table when making any and all adjustments to height or table
sections.
Do not sit or allow patients to sit on the Head Section of the table.•
The Head Section will involuntarily lower as it is not designed to
support sitting.
Support the table section(s) with both hands when making any•
adjustments.
Inspect cables and connectors before each use.•
Adapta® ADP400

4
ABOUT ADAPTA ADP400 TABLE
Use only accessories that are specially designed for the Adapta•
ADP400 traction table. Do not use accessories manufactured
by other companies on the Adapta ADP400. DJO, LLC is not
responsible for any consequence resulting from using products
manufactured by other companies. The use of other accessories or
cables may result in increased emissions or decreased immunity of
the Adapta ADP400.
When making adjustments to the table sections, make certain the•
patient weight is removed before adjusting.
Do not lift table by Head Section.•
Never transport a patient on the ADP400 table. This table is not•
designed to support a patient during transport.
Do not smoke on or around the table.•
Do not allow any unsupervised patient access to the traction table.•
The table sections should be locked before the loading or•
unloading of a patient. Do not reposition or allow the patient to
get on or off the table while the table is ascending or descending.
This table should only be operated under the prescription and•
supervision of a licensed medical practitioner that is familiar with
the precautionary measures and operational functions associated
with the table being used.
Do not allow anything to be under the table while the table is in•
operation.
Adapta® ADP400

5
TABLE FAMILIARIZATION
NOMENCLATURE
HEAD
SECTION
MID
SECTIONS
LOWER
SECTION
HEAD
SECTION LOCK
RELEASE
MID SECTION
LOCK RELEASE
LOWER SECTION
LOCK RELEASE
UPPER
FRAME
LOWER FRAME
FOOT PEDAL
OPTIONAL
TRACTION
UNIT STAND
CASTERS
GLIDE LEVELING
FEET
RETRACTABLE
CASTER
RAISE/
LOWER LEVER
OPTIONAL
Adapta® ADP400

6
TECHNICAL SPECIFICATIONS
Meets Directive 93 /42 /EEC
IEC/UL/EN: 60601-1
EN 60601-1-2
CAN/CSA C22.2 No. 601.1
Operation 120V 230V
Rated Frequency: 60 Hz 50/60 Hz
Current: 1.6A 1.0A
Power Input: 200W 230W
Fuses: 1.6A (Non-serviceable) 1.0A (Non-serviceable)
Lifting Capacity: 400 lbs (182 kg) 400 lbs (182 kg)
Protected: Class I, Type B Class I, Type B
Duty Cycle: 10% 10%
Table Length (Head to Toe): 77 in (195.6 cm) 77 in (195.6 cm)
Adapta® ADP400

7
TECHNICAL SPECIFICATIONS
TABLE DIMENSIONS
NOSE AND FOOT CUSHIONS
INCLINE UP TO 90°
25°
21.5 in - 41.5 in
(54.6 cm - 105.4 cm)
Adapta® ADP400

8
TECHNICAL SPECIFICATIONS
CUSHION DIMENSIONS
97 in (246.4 cm)
27 in
(68.6 cm)
77 in (195.6 cm)
23 in (58.4 cm)
26 in (66 cm) 16 in (40.6 cm) 9 in
(23 cm)
Adapta® ADP400

9
TECHNICAL SPECIFICATIONS
ELECTROMAGNETIC COMPATIBILITY TABLES
The following tables apply on to the 230 Vac System.
Guidance and manufacturer’s declaration – electromagnetic emissions
The Adapta ADP400 traction table is intended for use in the electromagnetic environment specified below. The
customer or the user of the Adapta ADP400 traction table should assure that it is used in such an environment.
Emission tests Compliance Electromagnetic environment -
guidance
RF emissions
CISPR 11 Group 1
The Adapta ADP400 traction table
uses RF energy only for its internal
function. Therefore, its RF
emissions are very low and are not
likely to cause any interference in
nearby electronic equipment.
RF emissions
CISPR 11 Class B
The Adapta ADP400 traction table
is suitable for use in all
establishments, including domestic
establishments and those directly
connected to the public low-voltage
power supply network that supplies
buildings used for domestic
purposes.
Harmonic emissions
IEC 61000-3-2 Class A
Voltage fluctuations
IEC 61000-3-3 Complies
Adapta® ADP400

10
TECHNICAL SPECIFICATIONS
ELECTROMAGNETIC COMPATIBILITY TABLES
Guidance and manufacturer’s declaration – electromagnetic immunity
The Adapta ADP400 traction table is intended for use in the electromagnetic environment specified below. The
customer or the user of the Adapta ADP400 traction table should assure that it is used in such an environment.
Immunity test IEC 60601
test level Compliance level Electromagnetic environment - guidance
Electrostatic discharge
(ESD)
IEC 61000-4-2
±6kV contact
±8kV air
±6kV contact
±8kV air
Floors should be wood,
concrete or ceramic tile. If
floors are covered with
synthetic material, the
relative humidity should
be at least 30%.
Electrical fast
transient/burst
IEC 61000-4-4
±2kV for power supply
lines
±1kV for input/output
lines
±2kV for power supply
lines
±1kV for input/output
lines
Mains power quality
should be that of a typical
commercial or hospital
environment.
Surge (1)
IEC 61000-4-5
±1kV differential mode
±2kV common mode
±1kV differential mode
±2kV common mode
Mains power quality
should be that of a typical
commercial or hospital
environment.
Voltage dips, short
interruptions and voltage
variations on power
supply input lines
IEC 61000-4-11
<5% UT
(>95% dip in UT)
for 0.5 cycle
40% UT
(60% dip in UT)
for 5 cycles
70% UT
(30% dip in UT)
for 25 cycles
<5% UT
(>95% dip in UT) for 5 sec
<5% UT
(>95% dip in UT)
for 0.5 cycle
40% UT
(60% dip in UT)
for 5 cycles
70% UT
(30% dip in UT)
for 25 cycles
<5% UT
(>95% dip in UT) for 5 sec
Mains power quality
should be that of a typical
commercial or hospital
environment. If the user of
the Adapta ADP400
traction table requires
continued operation
during power mains
interruptions, it is
recommended that the
Adapta ADP400 traction
table be powered from an
uninterrupted power
supply or a battery.
Power frequency
(50/60Hz) magnetic field
IEC 61000-4-8
3 A/m 3 A/m
Power frequency magnetic
fields should be at levels
characteristic of a typical
location in a typical
commercial or hospital
environment.
NOTE UTis the a.c. mains voltage prior to application of the test level.
NOTE (1) – These results apply to the 230 Vac Power Supply.
Guidance and manufacturer’s declaration – electromagnetic immunity
The Adapta ADP400 traction table is intended for use in the electromagnetic environment specified below. The
customer or the user of the Adapta ADP400 traction table should assure that it is used in such an environment.
Immunity test IEC 60601
test level Compliance level Electromagnetic environment - guidance
Portable and mobile RF
communications equipment
should be used no closer to any
part of the Adapta ADP400
traction table, including cables,
than the recommended separation
distance calculated from the
equation applicable to the
frequency of the transmitter.
Recommended separation
distance
Conducted RF
IEC 61000-4-6
3 Vrms
150 kHz to 80 MHz
3 V d= [3.5]√P
V1
Radiated RF
IEC 61000-4-3
3 V/m
80 MHz to 2.5 GHz
3 V/m d= [3.5]√P80 MHz to 800 MHz
E1
d= [7]√P800 MHz to 2.5 GHz
E1
where Pis the maximum output
power rating of the transmitter in
watts (W) according to the
transmitter manufacturer and dis
the recommended separation
distance in meters (m).
Field strengths from fixed RF
transmitters, as determined by an
electromagnetic site surveya,
should be less than the compliance
level in each frequency rangeb.
Interference may occur in the
vicinity of equipment marked with
the following symbol:
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.
aField strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land
mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically
with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site
survey should be considered. If the measured field strength in the location in which the Adapta ADP400 traction
table is used exceeds the applicable RF compliance level above, the Adapta ADP400 traction table should be
observed to verify normal operation. If abnormal performance is observed, additional measures may be
necessary, such as reorienting or relocating the Adapta ADP400 traction table.
bOver the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Adapta® ADP400

11
TECHNICAL SPECIFICATIONS
ELECTROMAGNETIC COMPATIBILITY TABLES
Recommended separation distances between portable and mobile RF communications equipment and the
Adapta ADP400 traction table
The Adapta ADP400 traction table is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the Adapta ADP400 traction table can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the Adapta ADP400 traction table as recommended below.
Rated maximum output
power of transmitter
W
Separation distance according to frequency of transmitter
m
150 kHz to 80 MHz
d= [3.5]√P
V1
80 MHz to 800 MHz
d= [3.5]√P
E1
800 MHz to 2.5 GHz
d= [7]√P
E1
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
11.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance din
meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where Pis the
maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.
Adapta® ADP400

12
SETUP
CONTENTS OF CRATE
After removing top and side panels of shipping crate, you may notice
metal bands and plastic straps. These are used to secure various
sections of the table and must be removed before the table can be
lifted out. The table must be lifted directly upward in order to clear all
shipping restraints.
Visually inspect for damage. Report any damage to the carrier
immediately.
A MINIMUM OF TWO PEOPLE WILL BE REQUIRED TO LIFT AND
MOVE THE TABLE. TABLE SHOULD BE LIFTED BY THE BASE
FRAME.
Do not lift the table by the Head Section.•
Contents of Crate:
Model ADP400:
•AdaptaADP400Table
•TractionUnitStand
•PivotPlate
•MainsPowerCord-130in(330cm)incablelength,unshielded,18AWG
•HandControl-32in(81cm)incablelength,unshielded,26AWG
•FootPedal(Optional) - 32 in (81 cm) in cable length, unshielded, 26 AWG
•UserManual(CD-ROM)
Glide Leveler Adjustments:
Use a carpenter’s level (fluid bubble type) to make adjustments to
each Glide Leveler of the table and tighten each glide with a regular
crescent wrench.
Adapta® ADP400

13
SETUP
ATTACHING TRACTION UNIT STAND TO TABLE
Attach the Pivot Plate to the table
and fasten with the two supplied
1/4-20 screws.
NOTE: Make sure that the holes
of the Pivot Plate and the
table are aligned before
securing the Pivot Plate to
the table.
Attach the two supplied 1/4-20
ESNA nuts to each screw and
tighten with a 7/16" wrench.
Attach the Traction Unit Stand to
the aligning holes of the Pivot Plate
and the table.
Place the two supplied 13 mm
flat washers underneath the Pivot
Plate.
Attach the two supplied 9/16"
ESNA nut and tighten with a 9/16"
wrench.
Position the adjustment knob
of the Traction Unit Stand to the
desired degree of the Pivot Plate.
Adapta® ADP400

14
SETUP
MOUNTING TRACTION UNIT TO STAND
NOTE: The traction unit should be mounted facing the direction of
pull so the Traction Cord does not contact the side of the slot
from which it extends.
1. To secure the traction unit to the
traction stand, loosen the
clamp from the traction unit. Fit
the traction unit to the stand and
tighten the clamp up onto the
stand.
2. Attach the mounting screw onto
the traction stand at the front
of the unit. The mounting screw is
provided with traction units only.
•Topreventaccidentaldisengagement,thetractionunitmustbe
securely attached to the mounting surface of the traction stand. It is
the responsibility of the user to verify the adequacy of the
installation before use in patient therapy.
•ThetractionstandisdesignedforChattanoogatraction
units only. Securement of other traction units need to follow
traction manufacturing recommendations. DJO, LLC is not
responsible for any consequence resulting from using products
manufactured by other companies.
Adapta® ADP400

15
OPERATION
ADJUSTING TABLE SECTIONS
When making adjustments to the table sections, make certain the•
patient weight is removed before adjusting.
Never place your hands and feet near the working mechanism of•
the table when making any and all adjustments to height or table
sections.
Elevating Head Section
Raise the Head Section by hand to
the desired elevation.
Lowering Head Section
Lift the Head Section lever and
lower the Head Section to the
desired elevation.
Support the Head Section when
lowering.
Locking Mid Section
Turn the Lock Release Knob
toward the Lower Section of the
table to lock the Mid Section in
place.
Unlocking Mid Section
Turn the Lock Release Knob
toward the Head Section of the
table to unlock the Mid Section.
Adapta® ADP400

16
OPERATION
ADJUSTING TABLE SECTIONS
Elevating Lower Section
Raise the Lower Section to the
desired elevation.
Lowering Lower Section
Turn the Lower Section lever and
move the Lower Section down to
the desired elevation.
TABLE HEIGHT ADJUSTMENT
Raising and Lowering Table
Push the Up Arrow button to raise
the table and the Down Arrow
button to lower the table to the
desired height.
Raising and Lowering Table
with Optional Foot Pedal
Step on the corresponding side
of the foot pedal to raise or lower
the table to the desired height.
Adapta® ADP400

17
OPERATION
RELOCATING THE TABLE WITH OPTIONAL RETRACTABLE CASTER
Never transport a patient on the ADP400 table. This table is not•
designed to support a patient during transport.
Moving the Table
Push the Caster Lock lever
completely down with the foot.
This will bring the swivel caster
down to allow the table to be
moved to another location.
Parking the Table
After moving the table to the
desired location, raise the Caster
Lock lever with toe of the shoe.
This will raise the swivel caster and
cease table movement.
Adapta® ADP400