Chauvet Professional onAirPanel1IP User manual

User Manual
Model ID: ONAIRPANEL1IP

onAir IP Panel 1 User Manual Rev. 2
Edition Notes
The onAir IP Panel 1 User Manual includes a description, safety precautions, installation, programming,
operation and maintenance instructions for the onAir IP Panel 1 as of the release date of this edition.
Trademarks
CHAUVET, the Chauvet logo and onAir IP Panel 1 are registered trademarks or trademarks of Chauvet &
Sons, LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company
and product names and logos referred to herein may be trademarks of their respective companies.
Copyright Notice
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2022 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional information purposes
only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification, or printing of this
manual or its content for any other purpose without written consent from Chauvet.
Document Printing
For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4
paper (210 x 297 mm), configure the printer to scale the content accordingly.
Intended Audience
Any person installing, operating, and/or maintaining this product should completely read through the guide
that shipped with the product, as well as this manual, before installing, operating, or maintaining this
product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetprofessional.com.
Document Revision
This onAir IP Panel 1 User Manual is the 2nd edition of this document. Go to
www.chauvetprofessional.com for the latest version.

onAir IP Panel 1 User Manual Rev. 2
Table of Contents
i
TABLE OF CONTENTS
1. Before You Begin ....................................................................... 1
What Is Included ........................................................................................... 1
Claims ........................................................................................................... 1
Text Conventions .......................................................................................... 1
Symbols ........................................................................................................ 1
FCC Compliance........................................................................................... 1
RF Exposure Warning for North America, and Australia............................... 1
Safety Notes.................................................................................................. 2
Personal Safety.................................................................................................. 2
Mounting and Rigging ........................................................................................ 2
Power and Wiring............................................................................................... 2
Operation ........................................................................................................... 2
Expected LED Lifespan................................................................................. 2
2. Introduction ................................................................................ 3
Description .................................................................................................... 3
Features........................................................................................................ 3
Product Overview.......................................................................................... 3
Product Dimensions ...................................................................................... 4
3. Setup ........................................................................................... 5
AC Power...................................................................................................... 5
AC Plug .............................................................................................................. 5
Power Linking..................................................................................................... 5
DC Power...................................................................................................... 5
USB Software Update ................................................................................... 5
Signal Connections ....................................................................................... 6
Control Personalities .......................................................................................... 6
DMX Linking....................................................................................................... 6
Remote Device Management (RDM)....................................................................... 6
Art-Net™ Connection ......................................................................................... 6
sACN Connection............................................................................................... 6
Ethernet Connection Diagram............................................................................ 6
Lumenradio CRMX™ Connection...................................................................... 7
Initial Setup.............................................................................................................. 7
Configuration ........................................................................................................... 7
Product Pairing ........................................................................................................ 7
Accessory Slots............................................................................................. 7
Mounting ....................................................................................................... 8
Orientation.......................................................................................................... 8
Rigging ............................................................................................................... 8
Procedure........................................................................................................... 8
4. Operation .................................................................................... 9
Control Panel Description ............................................................................. 9
Control Options ............................................................................................. 9
Programming................................................................................................. 9
Menu Map ..................................................................................................... 10
Home Screen ................................................................................................ 13
Example Home Screens .................................................................................... 13
Configuration (DMX, Art-Net™, sACN) ......................................................... 14
Control Mode...................................................................................................... 14
Control Personalities .......................................................................................... 14
Starting Address................................................................................................. 14

Table of Contents
onAir IP Panel 1 User Manual Rev. 2
ii
Ethernet Setting ................................................................................................. 14
Universe .................................................................................................................. 14
Start Channel........................................................................................................... 14
IP Address ............................................................................................................... 15
Ethernet to DMX ...................................................................................................... 15
Control Channel Assignments and Values.................................................... 15
XYExtended(10)................................................................................................. 15
XYBasic(6) ......................................................................................................... 15
16Ch................................................................................................................... 16
15Ch2................................................................................................................. 16
15Ch1................................................................................................................. 17
11Ch................................................................................................................... 17
10Ch................................................................................................................... 18
8Ch2................................................................................................................... 18
8Ch1................................................................................................................... 19
6Ch..................................................................................................................... 19
5Ch..................................................................................................................... 19
4Ch..................................................................................................................... 19
3Ch..................................................................................................................... 19
1Ch..................................................................................................................... 20
Control Chart...................................................................................................... 20
Color Temperature Chart ................................................................................... 20
Configuration (Standalone) ........................................................................... 21
CCT Control ....................................................................................................... 21
Preset Buttons ......................................................................................................... 21
HSV Control ....................................................................................................... 21
XY Control.......................................................................................................... 21
Preset CCTs....................................................................................................... 21
Manual Color Mixer ............................................................................................ 21
Effect Macros ..................................................................................................... 22
Configuration (Settings) ................................................................................ 22
Red Shift ............................................................................................................ 22
Master/Slave ...................................................................................................... 22
DMX Loss........................................................................................................... 22
Dimmer Curve .................................................................................................... 22
Dimmer Speed Mode ......................................................................................... 22
Color Calibration ................................................................................................ 22
Pulse Width Modulation ..................................................................................... 22
Fan Mode ........................................................................................................... 22
Wireless Lumenradio CRMX™ Settings ............................................................ 23
Toggle CRMX™ ...................................................................................................... 23
Receiver Reset ........................................................................................................ 23
Wireless to DMX...................................................................................................... 23
Display Backlight................................................................................................ 23
Information ......................................................................................................... 23
Factory Reset..................................................................................................... 23
Web Server ................................................................................................... 23
Home.................................................................................................................. 23
Settings .............................................................................................................. 23
Output ................................................................................................................ 23
Security .............................................................................................................. 23
5. Maintenance................................................................................ 24
Product Maintenance .................................................................................... 24
6. Technical Specifications ........................................................... 25
Returns............................................................................................ 26
Contact Us ...................................................................................... 27

Page 1 of 27
onAir IP Panel 1 User Manual Rev. 2
Before You Begin
1. Before You Begin
What Is Included
Claims
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Text Conventions
Symbols
FCC Compliance
This device complies with Part 15 Part B of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
RF Exposure Warning for North America, and Australia
Warning! This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20cm between
the radiator and your body. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
• onAir IP Panel 1
• Seetronic Powerkon IP65 power cord
• Omega bracket with mounting hardware
•Juniorpin
• Quick Reference Guide
Convention Meaning
1–512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
<ENTER> A key to be pressed on the product’s control panel
Symbol Meaning
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
Any reference to data or power connections in this manual assumes the use of Seetronic
IP rated cables.
The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data
transmission protocol.

Page 2 of 27
Before You Begin
onAir IP Panel 1 User Manual Rev. 2
Safety Notes
Read all the following safety notes before working with this product. These notes contain important
information about the installation, usage, and maintenance of this product.
Personal Safety
• Avoid direct eye exposure to the light source while the product is on.
• Always disconnect the product from the power source before cleaning or replacing the fuse.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Do not touch the product’s housing when operating because it may be very hot.
Mounting and Rigging
• The product is intended for professional use only.
• Do not submerge this product (IP65). Temporary outdoor operation is fine.
• When using this product in an outdoor environment, use IP65 (or higher) rated power and data
cables. Secure unused power and data ports with attached IP65 covers.
•
CAUTION: When transferring product from extreme temperature environments, (e.g., cold truck to warm
humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a
failure, allow product to fully acclimate to the surrounding environment before connecting it to power.
• Not for permanent outdoor installation in locations with extreme environmental conditions. This
includes, but is not limited to:
• Exposure to a marine/saline environment (within 3 miles of a saltwater body of water).
• Locations where the normal high or low temperatures exceed the temperature ranges in this manual.
• Locations that are prone to flooding or being buried in snow.
• Areas where the product will be subjected to extreme radiation or caustic substances.
• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
• The product should be positioned so that prolonged staring into it at a distance closer than 19.7 in
(50 cm) is not expected.
• Make sure there are no flammable materials within 7.87 in (20 cm) of this product while it is operating.
• When hanging this product, always secure to a fastening device using a safety cable.
• Never carry the product by the power cord.
Power and Wiring
• Make sure the power cord is not crimped or damaged.
• Ensure that the product is connected to the proper voltage in accordance with the specifications in
this manual or on the product’s specification label.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
• Never connect this product to a dimmer pack or rheostat.
• Make sure to replace the fuse with another of the same type and rating.
• Never disconnect this product by pulling or tugging on the power cable.
• If the external flexible cable or cord of this product is damaged, it shall be replaced with a special
cable or cord exclusively available from the manufacturer or its service agent.
• The light source contained in this luminaire shall only be replaced by the manufacturer, its service
agent, or a similarly qualified person.
Operation
• Do not operate this product if there is damage on the housing, lenses, or cables. Have the damaged
parts replaced by an authorized technician at once.
• Do not cover the ventilation slots when operating to avoid internal overheating.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate the product at higher temperatures.
• The minimum startup temperature is -4°F (-20°C). Do not start the product at lower temperatures.
• The minimum ambient temperature is -22°F (-30°C). Do not operate the product at lower temperatures.
• In the event of a serious operation problem, stop using this product immediately!
Expected LED Lifespan
Over time, use and heat will gradually reduce LED brightness. Clustered LEDs produce more heat than single LEDs,
contributing to shorter lifespans if always used at full intensity. The average LED lifespan is 40,000 to 50,000
hours. To extend LED lifespan, maintain proper ventilation around the product, and limit the overall intensity.
This product contains no user-serviceable parts. Any reference to servicing in this User
Manual will only apply to properly trained, certified technicians. Do not open the housing
or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.
If your Chauvet product requires service, contact Chauvet Technical Support.

Page 3 of 27
onAir IP Panel 1 User Manual Rev. 2
Introduction
2. Introduction
Description
The onAir IP Panel 1 is an IP65 full-spectrum LED soft light with a 1x1 format for outdoor or indoor
operation. Ready for any broadcast setting, the onAir IP Panel 1 features high CRI/ TLC and TM-30
scores, a smooth 16-bit dimming curve, +/- green adjustment, an emulated redshift, built-in customizable
effects, and a drop-in slot for easy changing of accessories. Mounting options include a Jr Pin and an
Omega Bracket. PWM, DMX, RDM, CRMX™, Art-Net™, sACN, and an onboard control option ensure
camera-ready use. An optional 28 VDC input via 3-pin XLR enables use of an external battery pack to add
increased flexibility for all remote needs.
Features
• Full-spectrum LED 1x1 format soft light panel style fixture for broadcast, film, and special events
• IP65 rating for all weather use indoors or out.
• Linear color temperature presets from 2800 K to 8000 K with high CRI and CQS
• Virtual color wheel with color matched to popular gel colors
• +/- Green adjustment and emulated red-shift via DMX or on-board control
• RDM (Remote Device Management) and CRMX Wireless Control for added flexibility
• Adjustable PWM (Pulse Width Modulation) to avoid flickering on camera
• Virtually silent operation for use in studio applications
• Ultra-smooth 16-bit dimming curves and speeds to complement any lighting scheme.
• Easily switch mounting options from Jr Pin to Omega Bracket
• Drop-in slot for diffusers and intensifier filter (sold separately)
• Rugged design for years of rough use in the most extreme conditions.
• Easy to use on-board control with full access to all the features of the fixture without the need for a
dedicated controller.
• USB port for fixture software updates
• 28 VDC power input via 3-pin XLR to power the fixture from an external battery pack
Product Overview
Menu
buttons
LCD
display
5-pin
DMX
in
Power
out
Carry
handle
(x4)
Power
in
Control
knobs
Ethernet
port
CRMX™
antenna
USB C
port
5-pin
DMX
out
28 VDC
power
in
Ethernet
port
Preset
buttons

Page 4 of 27
Introduction
onAir IP Panel 1 User Manual Rev. 2
Product Dimensions
13.98 in
355 mm
22 in
559 mm
11.81 in
300 mm
21.81 in
554 mm
16.18 in
411 mm
19.6 in
497.8 mm
5.74 in
146 mm
13.97 in
354.9 mm
17.05 in
433.1 mm
1.1 in
28 mm

Page 5 of 27
onAir IP Panel 1 User Manual Rev. 2
Setup
3. Setup
AC Power
The onAir IP Panel 1 has an auto-ranging power supply and it can work with an input voltage range of 100
to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current
value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
The listed current rating indicates the product’s average current draw under normal conditions.
AC Plug
The onAir IP Panel 1 comes with a power input cord terminated with a Seetronic Powerkon IP65 connector
on one end and an Edison plug on the other end (U.S. market). If the power input cord that came with your
product has no plug, or if you need the change the plug, use the table below to wire the new plug.
Power Linking
The product supports power linking. You can power link up to 7 products at 100 V, up to 8 products at 120
V, up to 15 products at 208 V, up to 16 products at 230 V, or up to 17 products at 240 V.
This product comes with a power input cord. Power linking cables are available from Chauvet for purchase.
DC Power
The onAir IP Panel 1 has a 3-pin IP65 XLR power input that can work with an input voltage of 28 VDC
which is SELV voltage supplied by short-circuit-proof power supply.
USB Software Update
The onAir IP Panel 1 allows for software update through USB using the built-in USB port. To update the
software using a USB type C flash drive, do the following:
1. Power on the fixture and plug the flash drive into the USB port.
2. Once the flash drive has been detected, the message “Upgrade Firmware” will be displayed.
Press <ENTER>. If a different message appears on the display, search for the update software in
the main menu (Upgrade Firmware) and select from Only This Fixture, Multiple Fixture, or
Other Fixture Type. A list of the software update files will be displayed.
3. Select the file that needs to be uploaded. The message “Are you sure?” will be displayed. Press
<ENTER>.
4. If the selected file is correct, the update will be completed. Restart the product.
If the selected file is incorrect, the update will fail, and the display will go back to the main interface.
Repeat steps 1-3 using the correct file.
• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure
the product has an appropriate electrical ground to avoid the risk of electrocution or
fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
If AC power and DC power are input to the product at the same time, the product will
automatically give priority to AC power input.
The “Other Fixture Type” option can only be selected for connected products compatible
with the Upload 03 (the first 2 digits on the item code must be 03).

Page 6 of 27
Setup
onAir IP Panel 1 User Manual Rev. 2
Signal Connections
The onAir IP Panel 1 can receive a DMX, Art-Net™, sACN, or a wireless Lumenradio CRMX™ signal. The
product has 2 Seetronic Etherkon-compatible through ports and 5-pin DMX in and out ports. If using other
compatible products with this product, you can control each individually with a single controller.
Control Personalities
The onAir IP Panel 1 uses a 5-pin DMX data connection, Art-Net™, sACN, or wireless CRMX™ for its 14
control personalities, ranging from 1Ch to 16Ch.
• Refer to the Operation chapter to learn how to configure the onAir IP Panel 1 to work in these
personalities.
• The Control Channel Assignments and Values section provides detailed information regarding the
control personalities.
DMX Linking
You can link the onAir IP Panel 1 to a DMX controller using a 5-pin DMX connection or a CRMX™
connection. For more information about DMX, read the DMX primer at: https://
www.chauvetprofessional.com/wp-content/uploads/2016/06/DMX_Primer.pdf.
Remote Device Management (RDM)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate
bi-directionally along existing DMX cabling. Check the DMX controller’s User Manual or with the
manufacturer as not all DMX controllers have this capability. The onAir IP Panel 1 supports RDM protocol
that allows feedback to make changes to menu map options.
Art-Net™ Connection
Art-Net™ is an Ethernet protocol that uses TCP/IP which transfers a large amount of DMX512 data using
an ethernet connection over a large network. An Art-Net™ protocol document is available from
www.chauvetprofessional.com.
Art-Net™ designed by and copyright Artistic Licence Holdings Ltd.
sACN Connection
Also known as ANSI E1.31, streaming ACN is an Ethernet protocol that uses the layering and formatting of
Architecture for Control Networks to transport DMX512 data over IP or any other ACN compatible network.
Ethernet Connection Diagram
If you are not familiar with or need more information about DMX standards or the DMX
cables needed to link this product to a DMX controller, download the DMX Primer from the
Chauvet website: www.chauvetprofessional.com.
Computer/
controller
(running Art-Net™
or sACN protocol)
Switch or router
onAir IP Panel 1
To other Art-Net™ or sACN devices

Page 7 of 27
onAir IP Panel 1 User Manual Rev. 2
Setup
Lumenradio CRMX™ Connection
In optimal conditions, the onAir IP Panel 1 can operate up to 300 m (900 ft) away from the CRMX™
transmitter, The CRMX™ receiver in the onAir IP Panel 1 must be paired with the CRMX™ transmitter for
wireless operation.
Initial Setup
1. Turn the CRMX™ transmitter on.
2. Connect the CRMX™ transmitter to a DMX controller.
3. Place the onAir IP Panel 1 within 300 m from the CRMX™ transmitter.
4. Turn the onAir IP Panel 1 on.
Configuration
1. From the onAir IP Panel 1’s control panel, go to DMX Address.
2. Select the start address, as with any other DMX compatible product.
3. Go to Wireless Setting > Receive On/Off.
4. Select On. (The Signal Strength Indicator will show a ?in front of the bars)
5. Press the reset button on the CRMX™ transmitter. (The Signal Strength Indicator on the
onAir IP Panel 1 will show a ϟin front of the bars for 3 seconds while a connection is established.)
Product Pairing
If the onAir IP Panel 1 has already been paired with the CRMX™ transmitter, the Signal Strength Indicator
on top of the display will show the strength of the signal. In this case, the onAir IP Panel 1 is ready to work
in Wireless mode.
Pairing the onAir IP Panel 1 and a New CRMX™ Transmitter
1. From the onAir IP Panel 1 control panel, go to Wireless Setting > Receive Reset.
2. Select Yes.
3. From the CRMX™ transmitter, press <RESET>. The signal indicator on the transmitter will flash.
4. Once the transmitter has found the onAir IP Panel 1, the signal indicator on the CRMX™
transmitter will illuminate solid.
5. The display screen on the onAir IP Panel 1 will show the strength of the signal.
Accessory Slots
The onAir IP Panel 1 has 2 accessory slots that can be accessed by pressing the accessory slot tabs
inward and opening the hinged accessory slot cover.
• The back slot is for a diffuser or intensifier.
• The front slot is for accessories such as a honeycomb or barn doors.
CRMX™ operation can be interrupted or inhibited by people or liquid masses, including
water or snow, between the transmitter and receiver. For best results, keep the area
between the transmitter and receiver clear of any liquid masses.
• Do not use when the diffuser is removed. The diffuser cannot be removed when the
fixture is powered on.
• For fixed mounted luminaires, the risk group shall not exceed RG1 at the distance
obtaining 500 lx.

Page 8 of 27
Setup
onAir IP Panel 1 User Manual Rev. 2
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
For our CHAUVET Professional line of mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position, making sure there is adequate room for ventilation,
configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
• Before deciding on a location for the product, make sure there is easy access to the product for
maintenance and programming purposes.
• Make sure that the structure onto which you are mounting the product can support the product’s
weight. See the Technical Specifications for weight information.
• When mounting the product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
Procedure
The onAir IP Panel 1 comes with an omega bracket and a junior pin. Mounting clamps are sold separately.
Make sure the clamps are capable of supporting the weight of this product. Use at least two mounting
points per product. For the CHAUVET Professional line of mounting clamps, go to http://www.trusst.com/
products.
Mounting Diagram
Safety cableMounting clamp Omega bracket
Junior pin screw Junior pin

Page 9 of 27
onAir IP Panel 1 User Manual Rev. 2
Operation
4. Operation
Control Panel Description
Control Options
The onAir IP Panel 1 has 10 options for control:
• Wired DMX
Via 5-pin DMX port
• Wireless Lumenradio CRMX™
With the option to convert wireless input to wired DMX output
• Art-Net™ (wired ethernet)
With the option to convert ethernet input to wired DMX output
• sACN (wired ethernet)
With the option to convert ethernet input to wired DMX output
• CCT Control
Correlated Color Temperature, standalone with the control knobs
• HSV Control
Hue, Saturation, Value, standalone with the control knobs
•XYControl
Cartesian X and Y coordinates, standalone with the control knobs
• Preset CCTs
Preset Correlated Color Control options, standalone through the menu and preset buttons
• Manual Color Mixer
Individual color control to create custom colors, standalone through the display menu
•EffectMacros
Automatic programs, standalone through the display menu
Programming
Refer to the menu map to understand the menu options. The menu map shows the main menu and a
variable number of programming levels for each option.
• To access the main menu from the Home Screen, press <MENU>.
• To navigate to the desired option in the main menu, press <MENU> repeatedly until the option is
indicated, or use <UP> or <DOWN> to navigate directly.
• Press <ENTER> to select the indicated option.
• Use <UP> or <DOWN> to navigate within a programming level until the desired option is indicated.
• To return to the main menu, press <MENU> repeatedly until it shows on the display.
• Press and hold <MENU> to return to the home screen.
Control options can also be accessed through the Web Server.
Button/Knob Function
<MENU> Exits from the current menu or function
<ENTER> Enables the currently displayed menu or sets the currently selected value into the
selected function
<UP> Navigates upwards through the menu list or increases the numeric value when in a
function
<DOWN> Navigates downwards through the menu list or decreases the numeric value when
in a function
<DIM/INTENSITY> Increases or decreases the dimmer value or the intensity
<+/-GRN/HUE> Increases or decreases the green value, hue value, or X value
<CCT/
SATURATION> Increases or decreases the color temperature, saturation, or Y value
<PRESET A/B> Toggles between A presets (built-in) and B presets (custom)
<2800K/B1>
Selects a preset. Hold for 3 seconds to save the current look to the selected B
preset.
<3000K/B2>
<3200K/B3>
<4000K/B4>
<5000K/B5>
<5600K/B6>
<6000K/B7>
<6500K/B8>

Page 10 of 27
Operation
onAir IP Panel 1 User Manual Rev. 2
Menu Map
Refer to the onAir IP Panel 1 product page on www.chauvetprofessional.com for the latest menu map.
Main Menu Programming Levels Description
Protocol
DMX512
Sets the control protocolArtnet
sACN
DMX
Address 001–512*
Selects DMX address (*Highest
channel restricted to personality
chosen)
DMX
Channel
1Ch
Preset
CCTs Hue <-25–25> 1-channel: selects a preset CCT and hue
Manual
Color Mixer
Red <000–255> 1-channel: combine red, green, blue,
and white to make a custom color (0–
100%)
Green <000–255>
Blue <000–255>
White <000–255>
3Ch 3-channel: dimmer, color
temperature, hue
4Ch 4-channel: RGBW
5Ch 5-channel: 16-bit dimmer, color
temperature, hue, strobe
6Ch 6-channel: dimmer, RGBW, strobe
8Ch1 8-channel: RGBW 1 and 2
8Ch2 8-channel: 16-bit RGBW
10Ch 10-channel: dimmer, RGBW 1 and 2,
strobe
11Ch
11-channel: dimmer, RGBW, strobe,
color temperature, hue, effect
macros and speed, control
15Ch1
15-channel: 16-bit dimmer, 16-bit
RGBW, strobe, color temperature,
hue, effect macros and speed
15Ch2
15-channel: dimmer, RGBW 1 and 2,
strobe, color temperature, hue, effect
macros and speed, control
16Ch 16-channel: 16-bit RGBW 1 and 2
XYBasic(6) 6-channel: 16-bit dimmer, 16-bit X,
16-bit Y
XYExtended(10)
10-channel: 16-bit dimmer, 16-bit X,
16-bit Y, strobe, effect macros and
speed, control
Static
CCT Control Correlated color temperature control
HSV Control Hue, saturation, value control
XY Control X and Y coordinate control
Preset
CCTs
2800K
Dimmer
Hue
<000–255>
<-25–25>
Selects preset color temperature,
dimmer and hue
2900K
3000K
3100K
3200K
3300K
3400K
3500K
3600K
3700K
3800K
3900K
4000K
4100K

Page 11 of 27
onAir IP Panel 1 User Manual Rev. 2
Operation
Static
(cont.)
Preset
CCTs
(cont.)
4200K
Dimmer
Hue
<000–255>
<-25–25>
Selects preset color temperature,
dimmer and hue
4300K
4400K
4500K
4600K
4700K
4800K
4900K
5000K
5100K
5200K
5300K
5400K
5500K
5600K
5700K
6000K
6500K
7000K
7500K
8000K
Manual
Color Mixer
Red
<000–255> Combine red, green, blue, and white
to make custom color (0–100%)
Green
Blue
White
Effect
Macros
Color Chase
<001–100> Selects effect macro and speed
Police Car
Firetruck
Fire
Clouds
Fireworks
Paparazzi
Lightning
Red Shift On Enables or disables red shift
Off
Master/
Slave
Master Standalone mode
Slave Slave mode
DMX Loss
Hold Last Holds last signal received
Stop DMX Holds output
Blackout Blacks out the product
Dimmer
Curve
S Curve
Sets the dimmer curve
Linear
Square
Inverse Square
Dimmer
Mode
Off Instantaneous dimmer
Dimmer 1–3 Dimmer mode, fast (1) to slow (3)
Color
Calibration
Off Color calibration off
User
Calibration
Red
<125–255>
Sets maximum red LED value
Green Sets maximum green LED value
Blue Sets maximum blue LED value
White Sets maximum white LED value
Factory Calibration Color calibration set by factory
Main Menu Programming Levels Description

Page 12 of 27
Operation
onAir IP Panel 1 User Manual Rev. 2
LED
Frequency
600Hz
Sets the Pulse Width Modulation
frequency
1200Hz
2000Hz
4000Hz
6000Hz
25KHz
Fan Mode
Auto Sets the fan to auto mode
On Sets the fan to always on
Off Sets the fan to always off
Silent Sets the fan to silent
Wireless
Setting
Receive Off/
On
Off Enables/disables CRMX™
On
Receive
Reset
No Resets wireless receiver
Yes
Wireless To
DMX
No Enables/disables wireless to DMX
Yes
Back Light
10S Turns off display backlight after 10
seconds of inactivity
30S Turns off display backlight after 30
seconds
2Min Turns off display backlight after 2
minutes of
Always On Display backlight always on
Ethernet
Setting
Universe 000–255 (Art-net™) Sets the Art-Net™ or sACN universe
001–256 (sACN)
Start
Channel 001–512 Sets the starting channel
IP Address
2
000–255 . 000–255 . 000–
255
Sets the IP address10
239
Ethernet To
DMX
No Enables/disables Ethernet to DMX
Yes
Information
Fixture
Hours <_ _ _ _ _H> Shows total hours the product has been powered on
LED Hours <_ _ _ _ _H> Shows total hours the LEDs have
been powered on
Disp Ver <V_._ _> Shows current display version
Drv Ver <V_._ _> Shows current driver version
Net Ver <V_._ _> Shows current net version
UID 21A40 _ _ _ _ _ _ _ Shows product UID
Upgrade
Firmware
Only This
Fixture
_ _ _ _ _ _.CHL Selects an update file for this
product, or shows “No such file!”
...
Multiple
Fixture
_ _ _ _ _ _.CHL Selects an update file for this and
connected onAir IP Panel 1 products,
or shows “No such file!”
...
Other
Fixture
Type
_ _ _ _ _ _.CHL Selects an update file for other
connected products, or shows “No
such file!”
...
Factory
Reset
No Resets the product to factory default
settings
Yes
The “Other Fixture Type” option under Upgrade Firmware can only be selected for
connected products compatible with the Upload 03 (the first 2 digits of the item code must
be 03).
Main Menu Programming Levels Description

Page 13 of 27
onAir IP Panel 1 User Manual Rev. 2
Operation
Home Screen
The home screen of the onAir IP Panel 1 shows the current settings and status of the product. To see the
home screen, press and hold <MENU> until it shows on the display. From the home screen, press
<MENU> to access the menu.
Example Home Screens
Number Description
1Current product temperature
2Current wireless signal status
3Current preset or preset bank
4
Middle line shows current control mode. Shows DIM +/-GRN CCT in CCT mode, DIM HUE SAT
in HSV mode, DIM X Y in XY Control mode, Master Mode in master mode, Slave Mode in slave
mode, etc.
5Bottom line shows details of the current control mode
6Current dimmer or intensity value (00.0–100%) in CCT, HSV, or XY Control mode
7
Current +/- green value (-0.25–+0.25) in CCT mode, hue value (000–360°) in HSV mode, or X
value (0.00–0.850) in XY Control mode
8Current color temperature (2800–8000K) in CCT mode, saturation value (000–255) in HSV
mode, or Y value (0.00–0.850) in XY Control mode
876
5
4
321

Page 14 of 27
Operation
onAir IP Panel 1 User Manual Rev. 2
Configuration (DMX, Art-Net™, sACN)
Use control configurations to operate the product with a DMX, Art-Net™, or sACN controller.
Control Mode
The onAir IP Panel 1 works with wired DMX, CRMX™, Art-Net™, and sACN control signals. To select
which protocol to use:
1. Go to the Protocol main level.
2. Select the desired protocol, from DMX512, ArtNet, or sACN.
Control Personalities
To set the control personality:
1. Go to the DMX Channel main level.
2. Select the desired personality, from 1Ch, 3Ch, 4Ch, 5Ch, 6Ch, 8Ch1, 8Ch2, 10Ch, 11Ch, 15Ch1,
15Ch2, 16Ch, XYBasic(6), or XYExtended(10).
Starting Address
Each product will respond to a unique starting address from the controller. All products with the same
starting address will respond in unison. To set the starting address in DMX mode:
1. Go to the DMX Address main level.
2. Select the starting address (001–512).
Ethernet Setting
The Ethernet Settings control the universe, start address (Art-Net™ or sACN), IP address, and ethernet
conversion functions of the product.
Universe
To assign an Art-Net™ or sACN universe to the onAir IP Panel 1:
1. Go to the Ethernet Setting main level.
2. Select the Universe option.
3. Set the universe, from 000–255 (for Art-Net™) or from 001–256 (for sACN).
Start Channel
Each product will respond to a unique starting address from the controller. All products with the same
starting address will respond in unison. To set the starting address in Art-Net™ or sACN mode:
1. Go to the Ethernet Setting main level.
2. Select the Start Channel option.
3. Select the starting address (001–512)
• See the Wireless Lumenradio CRMX™ Settings section for further setup of CRMX™.
• See the Ethernet Setting section for further setup of ethernet protocols (Art-Net™ or sACN).
• See the Starting Address section for the highest starting address you can select for each
personality.
• Make sure that the starting addresses on the various products do not overlap due to the new
personality setting.
Personality Highest Address Products per Universe
1Ch 512 512
3Ch 510 170
4Ch 509 128
5Ch 508 102
6Ch 507 85
8Ch1 505 64
8Ch2
10Ch 503 51
11Ch 502 46
15Ch1 498 34
15Ch2
16Ch 497 32
XYBasic(6) 507 85
XYExtended(10) 503 51
• See the Starting Address section for the highest starting address you can select for each
personality.
• Make sure that the starting addresses on the various products do not overlap due to the new
personality setting.

Page 15 of 27
onAir IP Panel 1 User Manual Rev. 2
Operation
IP Address
To set the IP address:
1. Go to the Ethernet Setting main level.
2. Select the IP Address option.
3. Select the first value of the IP address, from 2, 10, or 239.
4. Press <ENTER> to cycle through the 4 values of the IP address.
5. Set the other 3 values from 000–255.
6. Press <MENU> to exit when the IP address is set as desired.
Ethernet to DMX
When Ethernet to DMX is active, the selected universe of the Art-Net™ or sACN signal will be converted to
DMX and output through the 5-pin DMX out port.
1. Go to the Ethernet Setting main level.
2. Select the Ethernet To DMX option.
3. Select from No (do not convert) or Yes (convert).
Control Channel Assignments and Values
XYExtended(10)
XYBasic(6)
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%
2 Fine dimmer 000 255 0–100%
3 X coordinate 000 255 0–100%
4 Fine X coordinate 000 255 0–100%
5 Y coordinate 000 255 0–100%
6 Fine Y coordinate 000 255 0–100%
7Strobe 000 010 No function
011 255 Strobe, slow to fast
8 Effect macros
000 010 No function
011 039 Color chase
040 068 Police car
069 096 Firetruck
097 125 Fire
126 154 Clouds
155 182 Fireworks
183 211 Paparazzi
212 240 Lightning
241 255 No function
9 Effect macro speed 000 255 Speed, slow to fast
10 Control 000 255 See the Control Chart
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%
2 Fine dimmer 000 255 0–100%
3 X coordinate 000 255 0–100%
4 Fine X coordinate 000 255 0–100%
5 Y coordinate 000 255 0–100%
6 Fine Y coordinate 000 255 0–100%

Page 16 of 27
Operation
onAir IP Panel 1 User Manual Rev. 2
16Ch
15Ch2
Channel Function Value Percent/Setting
1Red1 000 255 0–100%
2Finered1 000 255 0–100%
3Green1 000 255 0–100%
4 Fine green 1 000 255 0–100%
5Blue1 000 255 0–100%
6 Fine blue 1 000 255 0–100%
7White1 000 255 0–100%
8 Fine white 1 000 255 0–100%
9Red2 000 255 0–100%
10 Fine red 2 000 255 0–100%
11 Green 2 000 255 0–100%
12 Fine green 2 000 255 0–100%
13 Blue 2 000 255 0–100%
14 Fine blue 2 000 255 0–100%
15 White 2 000 255 0–100%
16 Fine white 2 000 255 0–100%
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%
2Red1 000 255 0–100%
3Green1 000 255 0–100%
4Blue1 000 255 0–100%
5White1 000 255 0–100%
6Red2 000 255 0–100%
7Green2 000 255 0–100%
8Blue2 000 255 0–100%
9White2 000 255 0–100%
10 Strobe 000 010 No function
011 255 Strobe, slow to fast
11 Color temperature 000 255 See the Color Temperature Chart
12 Hue 000 001 0
002 255 -25–+25
13 Effect macros
000 010 No function
011 039 Color chase
040 068 Police car
069 096 Firetruck
097 125 Fire
126 154 Clouds
155 182 Fireworks
183 211 Paparazzi
212 240 Lightning
241 255 No function
14 Effect macro speed 000 255 Speed, slow to fast
15 Control 000 255 See the Control Chart