Chauvet Professional Ovation E-190WW User manual

Quick Reference Guide
*Lens tubes sold separately
English EN
Español ES
Français FR
Nederlands NL
All manuals and user guides at all-guides.com
all-guides.com

Ovation™ E-190WW QRG EN
2
About this
Guide
The Ovation™ E-190WW Quick Reference Guide (QRG) has basic product
information such as connection, mounting, menu options, and DMX values.
Download the User Manual from www.chauvetprofessional.com
for more
details.
Disclaimer
The information and specifications contained in this QRG are subject to
change without notice.
Safety Notes
•DO NOT open this product. It contains no user-serviceable parts.
•DO NOT look at the light source when the product is on.
•To eliminate unnecessary wear and improve its lifespan, during
periods of non-use completely disconnect the product from power via
breaker or by unplugging it.
•CAUTION: When transferring product from extreme temperature
environments, (e.g. cold truck to warm humid ballroom) condensation
may form on the internal electronics of the product. To avoid causing a
failure, allow product to fully acclimate to the surrounding
environment before connecting it to power.
•CAUTION: This product’s housing may be hot when lights are
operating.
•Mount this product in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surfaces.
•DO NOT leave any flammable material within 50 cm of this product
while operating or connected to power.
•USE a safety cable when mounting this product overhead.
•DO NOT operate this product outdoors or in any location where dust,
excessive heat, water, or humidity may affect it.
•DO NOT operate this product if the housing, lenses, or cables appear
damaged.
•DO NOT connect this product to a dimmer or rheostat.
•ONLY connect this product to a grounded and protected circuit.
•ONLY use the hanging bracket to carry this product.
•In the event of a serious operating problem, stop using immediately.
•The maximum ambient temperature is 113 °F (45 °C). Do not operate
this product at higher temperatures.
Contact
Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux, contact
your distributor to request support or return a product. Visit
www.chauvetprofessional.com for contact information.
All manuals and user guides at all-guides.com

Ovation™ E-190WW QRG EN
3
What Is
Included
Ovation™ E-190WW
Neutrik® powerCON®
power cord
Warranty Card
Quick Reference Guide
AC Power
This product has an auto-ranging power
supply that can work with an input
voltage range of 100–240 VAC, 50/60 Hz.
To eliminate unnecessary wear and improve its lifespan, during periods
of non-
use completely disconnect the product from power via breaker
or by unplugging it.
Power Linking
You can link up to 4 Ovation™ E-190WW products at 120 VAC or 7
at
230 VAC. Power linking cords can be purchased separately.
AC Plug
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow/Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Replacing the
Fuse
1. Disconnect this product from power.
2. Using a Phillips #2 head screwdriver, unscrew the fuse holder cap
from the housing.
3.
Remove blown fuse and replace with a good fuse of the same type and
rating.
4. Screw the fuse holder cap back in place and reconnect power.
DMX Linking
The Ovation™ E-190WW
will work with a DMX controller using a regular
DMX serial connection. A DMX Primer is available from
www.chauvetprofessional.com.
DMX
Connection
The Ovation™ E-190WW
uses a regular DMX data connection for its
DMX personalities: UNO, DOS, and STD.P
. See the User Manual to
connect and configure for DMX operation.
Master Control
The Ovation™ E-190WW allows control of other Ovation
™
E-190WW products
using a regular DMX data connection. See the User
Manual to configure for Master Control operation.
Master/Slave
Connection
The Ovation™ E-
190WW uses the DMX data connection for its
Master/Slave mode. See
the User Manual to connect and configure for
Master/Slave operation.
All manuals and user guides at all-guides.com

Ovation™ E-190WW QRG EN
4
Mounting
Before mounting this product, read the Safety Notes. Make sure the
mounting clamp is capable of supporting the weight of the product. For our
Chauvet line of mounting clamps, go to trusst.com/productcategory/base-
plates-accessories-clamps/.
Product
Mounting
Diagram
Control Panel
Description
Button
Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently
selected value into the selected function
<UP>
Navigates upwards through the menu list and increases the
numeric value when in a function
<DOWN>
Navigates downwards through the menu list and decreases
the numeric value when in a function
Passcode
After being prompted, enter the following passcode by pressing:
•<UP>, <DOWN>, <UP>, <DOWN>, <ENTER>
This passcode cannot be changed and must be used whenever prompted.
Lens Tubes
The following lens tubes are available for purchase:
•19°, 26°, 36°, and 50° w/Gel frame (6.25 in/159 mm accessories)
•15°–30° and 25°–50° Zoom Gel frame (7.5 in/191 mm accessories)
Overhead Mounting
*Lens tubes sold separately
Secure the safety cable using
the passageway on the back
of the product.
Alternate Yoke Attachment
Safety Cable
Mounting Clamp
All manuals and user guides at all-guides.com

Ovation™ E-190WW QRG EN
5
Menu Options
Main Level
Programming Levels
Description
DIM
D.000–D.100
Local control of output
RUN
DMX
Sets the mode to Master/Slave
SLAV
ADDR
D.001-D.512
Sets the starting address
SET
KEY
OFF
Sets the key lock (passcode mode)
ON
DIMX
OFF
Slow (DIM4) to fast (DIM1) dimmer
speeds
DIM1
DIM2
DIM3
DIM4
CURV
CV1
Large (CV3) to small (CV1) dimmer
curves
CV2
CV3
OFF
SET
(Cont.)
PERF
LIVE
Balances LED cooling using fans and
output power level
STDO
Maintains LED cooling by limiting output
power level
POWR
Maintains LED cooling using fans allowing
full power output
SLCK
OFF
SET menu level access lock
ON
PERS
UNO
Selects DMX personality
DOS
STD.P
DERR
BLAK
Blacks out fixture upon loss of DMX
SAVE
Continues with last command upon loss of
DMX control
REST
****
(Enter
Passcode)
REST OK Resets fixture to factory defaults
MCON SELF
No DMX data is sent in standalone
operation
MAST
Sends DMX data to other Ovation™
E-190WW during standalone operation
All manuals and user guides at all-guides.com