Chauvet Freedom Stick User manual

01
User Manual

Page 2 of 22 Freedom Stick User Manual Rev. 3
TABLE OF CONTENTS
1. Before You Begin.......................................................................................................... 3
What Is Included .............................................................................................................................3
Unpacking Instructions....................................................................................................................3
Claims..................................................................................................................................................... 3
Text Conventions ............................................................................................................................3
Symbols ..........................................................................................................................................3
Disclaimer .......................................................................................................................................3
Product at a Glance ........................................................................................................................4
Safety Notes....................................................................................................................................4
2. Introduction................................................................................................................... 5
Product Overview............................................................................................................................5
Product Dimensions........................................................................................................................5
3. Setup.............................................................................................................................. 6
AC Power........................................................................................................................................6
Battery Power..................................................................................................................................6
Charging the Battery............................................................................................................................... 6
Battery Life Indicator............................................................................................................................... 6
Battery Run Time.................................................................................................................................... 6
Mounting .........................................................................................................................................7
Orientation.............................................................................................................................................. 7
Rigging ................................................................................................................................................... 7
4. Operation....................................................................................................................... 8
Control Panel Operation..................................................................................................................8
Menu Map .......................................................................................................................................8
Wireless DMX Linking.....................................................................................................................9
DMX Personality and Starting Address................................................................................................... 9
Wireless DMX Configuration................................................................................................................... 9
DMX Channel Assignments and Values.......................................................................................10
50CH .................................................................................................................................................... 10
50CH (cont.)......................................................................................................................................... 11
48CH .................................................................................................................................................... 11
48CH (cont.)......................................................................................................................................... 12
8-CH..................................................................................................................................................... 13
8-CH (cont.).......................................................................................................................................... 14
3-CH..................................................................................................................................................... 14
Configuration (Standalone)...........................................................................................................15
Automatic Programs............................................................................................................................. 15
Auto-Program Speed............................................................................................................................ 15
Sound-Active Mode .............................................................................................................................. 15
Sound Sensitivity.................................................................................................................................. 15
Preset Color Mode................................................................................................................................ 15
Custom Color Mixing ............................................................................................................................ 15
IRC-6 Infrared Remote Control.....................................................................................................16
IRC-6 Operation.................................................................................................................................... 17
Master/Slave Mode.......................................................................................................................18
5. Maintenance .................................................................................................................19
Product Maintenance....................................................................................................................19
6. Technical Specifications..............................................................................................20
Returns .............................................................................................................................21
Contact Us .........................................................................................................................22

Freedom Stick User Manual Rev. 3 Page 3 of 22
1.BEFORE YOU BEGIN
What Is
Included
•Freedom Stick
•External Power Supply
•Base Plate
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention
Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol
Meaning
Electrical warning. Not following these instructions may cause
electrical damage to the product, accessories, or the user.
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all
respects. However, Chauvet assumes no responsibility and specifically disclaims any
and all liability to any party for any loss, damage or disruption caused by any errors or
omissions in this document, whether such errors or omissions result from negligence,
accident or any other cause. Chauvet reserves the right to revise the content of this
document without any obligation to notify any person or company of such revision,
how
ever, Chauvet has no obligation to make, and does not commit to make, any such
revisions. Download the latest version from www.chauvetlighting.com.
The works of authorship contained in this manual, including, but not limited to, all design,
text and images are owned by Chauvet.
© Copyright 2016 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, Freedom Stick, and D-Fi are registered trademarks or
trademarks of Chauvet & Sons, LLC. (d/b/a Chauvet and Chauvet Lighting) in the United
States and other countries.
Other company and product names and logos referred to
herein may be trademarks of their respective companies.

Page 4 of 22 Freedom Stick User Manual Rev. 3
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Active
P
Replaceable Fuse
x
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•This product is not intended for permanent installation.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•This product is neither a toy nor a weapon.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product, be sure that they
receive this document.

Freedom Stick User Manual Rev. 3 Page 5 of 22
2.INTRODUCTION
Product Overview
Product Dimensions
DC Power In
On/Off
Switch
LED Display
Menu Buttons
LED Indicator
61 in
1550 mm
6.3 in
161 mm
Antenna
IR Sensor
Microphone

Page 6 of 22 Freedom Stick User Manual Rev. 3
3.SETUP
AC Power
The Freedom Stick has an external auto-
ranging power supply that can work with an
input voltage range of 100 to 240 VAC, 50/60 Hz.. To determine the product’s power
requirements (
circuit breaker, power outlet, and wiring), use the current value listed on
the label affixed to the product’s back panel, or refer to the product’s specifications chart.
The listed current rating indicates the product
’s average current draw under normal
conditions.
•Always connect the product to a protected circuit (circuit breaker or fuse).
Make sure the product has an appropriate electrical ground to avoid the risk
of electrocution or fire.
•To eliminate unnecessary wear and improve its lifespan, during periods of
non-use completely disconnect the product from power via breaker or by
unplugging it.
Never connect the product
to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Battery Power
The Freedom Stick comes with a rechargeable lithium battery for cable-free operation.
Charging the
Battery
The battery charges whenever the product is plugged into a power source. If the product
is plugged in and not in operation, make sure the On/Off switch is in the Off position.
Battery Life
Indicator
The indicators on the LED Menu Display show how much battery life remains available.
The drawing below provides a key to reading the battery life indicators.
100%
75%
50%
25%
Battery Run Time
Maximum Run Time
(all colors on)
Recharge Time
Up to 8 hours
4.5 hours

Freedom Stick User Manual Rev. 3 Page 7 of 22
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The Freedom Stick
may be mounted in any position; however, make sure adequate
ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
•Make sure that the structure onto which you are mounting the product can support
the product’s weight. See the Technical Specifications for weight information.
•When mounting the product overhead, always use a safety cable. Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, use a mounting clamp of appropriate weight
capacity.
•The base serves as a floor support. When mounting the product on the floor, make
sure that the product is away from people and vehicles.
Mounting Diagram
10 mm Threaded
Mounting Hole
(not visible)
Base Plate Bolt
Base Plate
Rubber Washer

Page 8 of 22 Freedom Stick User Manual Rev. 3
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display. Please refer to the Product Overview to see the button locations
on the control
panel.
Button
Function
<MENU>
Press to find an operation mode or to back out of the current menu
option
<UP>
Press to scroll up the list of options or to find a higher value
<DOWN>
Press to scroll down the list of options or to find a lower value
<ENTER>
Press to activate a menu option or a selected value
Menu Map
Main Function
Programming Levels
Description
DMX Mode
3-CH
d001–512 Selects DMX personality and DMX address
8-CH
48CH
50CH
Preset Colors
C--
C1–7
Static colors
Automatic Programs P--
P 1–21
Sets Auto Program 1–21
P 22–27
1--r
2--r
Sets Auto Program 22–27, color 1, and
color 2
1-rg
2-rg
1--g
2--g
1-gb
2-gb
1--b
2--b
1-rb
2-rb
1rgb
2rgb
1OFF
2OFF
P 28
Sets Auto Program 28 (cycles Auto
Programs 1–21)
P 29–34
Sets Auto Program 29–34 (designed for
Master/Slave mode)
P 35
Sets Auto Program 35 (cycles Auto
Programs 29–34)
Speed
S--
S 1–100
Program speed setting
Sound-Active Mode
Snd
Snd
Sets Sound-Active mode
Sound Sensitivity
SenS
u 0–100
Sound sensitivity setting
RGB Color Mixing U--
r 0–255
(red)
Custom static colors
Combine red, green, and blue
g 0–255
(green)
b 0–255
(blue)
Infrared Mode Set
ON
IR function on or off
OFF
Wireless DMX Mode S-tr ON
dtCH
dt 1–16
Turns on Wireless DMX mode and sets
transmitter or receiver channels
drCH
dr 1–16
OFF
Slave Mode SLA
SLA1
Sets Slave mode 1–4 (defines order of
Master/Slave programs)
SLA2
SLA3
SLA4
For programs 22–27, color 1 and color 2 cannot be assigned the same color.

Freedom Stick User Manual Rev. 3 Page 9 of 22
Wireless DMX
Linking
The Freedom Stick works with a DMX controller in Wireless DMX mode. In Wireless DMX
mode a lighting control board or D-Fi product must send
wireless DMX signals to the
products.
Information about DMX is in the DMX Primer, which is available from the
Chauvet website www.chauvetlighting.com/download.
DMX Personality
and
Starting
Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Freedom Stick uses up to 50 DMX channels in a 50-CH DMX mode, which defines
the highest configurable address to 463.
If you are not familiar with the DMX protocol, download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU> repeatedly until 3-CH, 8-CH, 48CH, or 50CH shows on the display.
2. Press <ENTER> and d 1–512 will show on the display.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
Wireless DMX
Configuration
The Freedom Stick offers wireless control of 2 or more products with a sin
gle DMX
controller. To set up the D-Fi 2.4 GHz transceiver, do the following.
For the transmitting product:
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until dtCH appears on the display.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select the transmitting signal (dt 1–dt16).
For the receiving product(s):
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until drCH appears on the display.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select the receiving signal (dr 1–dr16). The channel
number should match the transmitting signal you chose when setting up the
transmitting product.
Caution: D-Fi 2.4 GHz operation can be interrupted or inhi
bited by obstructions
between the transmitter and receiver such as structures or people. For best
results, keep the line of sight clear.
•The Freedom Stick is fully compatible with the D-Fi 2.4 GHz wireless
transceiver (transmitter/receiver) from Chauvet (sold separately). For more
detailed information about D-Fi 2.4 GHz functionality, refer to the D-Fi 2.4 GHz
User Manual available at the Chauvet website www.chauvetlighting.com.
•Ensure that all linked products are configured to the same DMX personality.

Page 10 of 22 Freedom Stick User Manual Rev. 3
DMX Channel Assignments and Values
50CH
Channel
Function
Value
Percent/Setting
1
Red 1
000 ó255 0–100%
2
Green 1
000
ó
255
0–100%
3
Blue 1
000 ó255 0–100%
4
Red 2
000 ó255 0–100%
5
Green 2
000 ó255 0–100%
6
Blue 2
000 ó255
0–100%
7
Red 3
000 ó255 0–100%
8
Green 3
000 ó255 0–100%
9
Blue 3
000 ó255 0–100%
10
Red 4
000 ó255
0–100%
11
Green 4
000 ó255 0–100%
12
Blue 4
000 ó255 0–100%
13
Red 5
000 ó255 0–100%
14
Green 5
000 ó255
0–100%
15
Blue 5
000 ó255 0–100%
16
Red 6
000 ó255 0–100%
17
Green 6
000 ó255 0–100%
18
Blue 6
000 ó255
0–100%
19
Red 7
000 ó255 0–100%
20
Green 7
000 ó255 0–100%
21
Blue 7
000 ó255 0–100%
22
Red 8
000 ó255
0–100%
23
Green 8
000 ó255 0–100%
24
Blue 8
000 ó255 0–100%
25
Red 9
000 ó255 0–100%
26
Green 9
000 ó255
0–100%
27
Blue 9
000 ó255 0–100%
28
Red 10
000 ó255 0–100%
29
Green 10
000 ó255 0–100%
30
Blue 10
000 ó255
0–100%
31
Red 11
000 ó255 0–100%
32
Green 11
000 ó255 0–100%
33
Blue 11
000 ó255 0–100%
34
Red 12
000 ó255
0–100%
35
Green 12
000
ó
255
0–100%
36
Blue 12
000 ó255 0–100%
37
Red 13
000 ó255 0–100%
38
Green 13
000 ó255
0–100%
39
Blue 13
000
ó
255
0–100%

Freedom Stick User Manual Rev. 3 Page 11 of 22
50CH
(cont.)
Channel
Function
Value
Percent/Setting
40
Red 14
000
ó
255
0–100%
41
Green 14
000
ó
255
0–100%
42
Blue 14
000 ó255 0–100%
43
Red 15
000 ó255
0–100%
44
Green 15
000
ó
255
0–100%
45
Blue 15
000
ó
255
0–100%
46
Red 16
000 ó255 0–100%
47
Green 16
000 ó255
0–100%
48
Blue 16
000
ó
255
0–100%
49 Strobe
000
ó
010
No function
011
ó
255
Strobe, slow to fast
50
Dimmer
000
ó
031
No function
48CH
Channel
Function
Value
Percent/Setting
1
Red 1
000 ó255 0–100%
2
Green 1
000 ó255 0–100%
3
Blue 1
000 ó255 0–100%
4
Red 2
000
ó
255
0–100%
5
Green 2
000 ó255 0–100%
6
Blue 2
000 ó255 0–100%
7
Red 3
000 ó255 0–100%
8
Green 3
000
ó
255
0–100%
9
Blue 3
000 ó255 0–100%
10
Red 4
000 ó255 0–100%
11
Green 4
000 ó255 0–100%
12
Blue 4
000
ó
255
0–100%
13
Red 5
000 ó255 0–100%
14
Green 5
000 ó255 0–100%
15
Blue 5
000 ó255 0–100%
16
Red 6
000
ó
255
0–100%
17
Green 6
000 ó255 0–100%
18
Blue 6
000 ó255 0–100%
19
Red 7
000 ó255 0–100%
20
Green 7
000
ó
255
0–100%
21
Blue 7
000 ó255 0–100%
22
Red 8
000 ó255 0–100%
23
Green 8
000 ó255 0–100%
24
Blue 8
000
ó
255
0–100%
25
Red 9
000 ó255 0–100%
26
Green 9
000 ó255 0–100%
27
Blue 9
000 ó255 0–100%

Page 12 of 22 Freedom Stick User Manual Rev. 3
48CH
(cont.)
Channel
Function
Value
Percent/Setting
28
Red 10
000
ó
255
0–100%
29
Green 10
000
ó
255
0–100%
30
Blue 10
000 ó255 0–100%
31
Red 11
000 ó255
0–100%
32
Green 11
000
ó
255
0–100%
33
Blue 11
000
ó
255
0–100%
34
Red 12
000 ó255 0–100%
35
Green 12
000 ó255
0–100%
36
Blue 12
000
ó
255
0–100%
37
Red 13
000
ó
255
0–100%
38
Green 13
000 ó255 0–100%
39
Blue 13
000 ó255
0–100%
40
Red 14
000
ó
255
0–100%
41
Green 14
000 ó255 0–100%
42
Blue 14
000 ó255 0–100%
43
Red 15
000 ó255
0–100%
44
Green 15
000
ó
255
0–100%
45
Blue 15
000 ó255 0–100%
46
Red 16
000 ó255 0–100%
47
Green 16
000 ó255
0–100%
48
Blue 16
000
ó
255
0–100%

Freedom Stick User Manual Rev. 3 Page 13 of 22
8-CH
Channel
Function
Value
Percent/Setting
1
Dimmer
000
ó
255
0–100%
2
Red
000
ó
255
0–100%
3
Green
000 ó255 0–100%
4
Blue
000 ó255
0–100%
5 Color Macros
000
ó
010
No function
011
ó
030
R: 100%
G: 0–100%
B: 0%
031 ó050
R: 100–0%
G: 100%
B: 0%
051 ó070
R: 0%
G: 100%
B: 0–100%
071 ó090
R: 0%
G: 100–0%
B: 100%
091 ó110
R: 0–100%
G: 0%
B: 100%
111
ó
130
R: 100%
G: 0%
B: 100–0%
131 ó150
R: 100%
G: 0–100%
B: 0–100%
151
ó
170
R: 100–0%
G: 100–0%
B: 100%
171 ó200
R: 100%
G: 100%
B: 100%
201
ó
205
Color 1
206
ó
210
Color 2
211
ó
215
Color 3
216
ó
220
Color 4
221
ó
225
Color 5
226
ó
230
Color 6
231
ó
235
Color 7
236
ó
240
Color 8
241 ó245 Color 9
246
ó
250
Color 10
251
ó
255
Color 11
6 Strobe
000
ó
010
No function
011
ó
255
Strobe, slow to fast

Page 14 of 22 Freedom Stick User Manual Rev. 3
8-CH
(cont.)
Channel
Function
Value
Percent/Setting
7 Auto Programs
000
ó
010
No function
011
ó
018
Auto program 1
019
ó
026
Auto program 2
027 ó034 Auto program 3
035
ó
042
Auto program 4
043
ó
050
Auto program 5
051 ó058 Auto program 6
059
ó
066
Auto program 7
067
ó
074
Auto program 8
075
ó
082
Auto program 9
083
ó
090
Auto program 10
091
ó
098
Auto program 11
099
ó
106
Auto program 12
107
ó
114
Auto program 13
115
ó
122
Auto program 14
123
ó
130
Auto program 15
131
ó
138
Auto program 16
139
ó
146
Auto program 17
147 ó154 Auto program 18
155
ó
162
Auto program 19
163
ó
170
Auto program 20
171
ó
178
Auto program 21
179
ó
186
Auto program 22
187 ó194 Auto program 23
195
ó
202
Auto program 24
203
ó
210
Auto program 25
211
ó
218
Auto program 26
219
ó
226
Auto program 27
227 ó234
Auto program 28 (cycle auto programs 1–21)
235
ó
255
Sound-Active program
8
Auto Speed
(When Ch. 7 is 011–234)
000 ó255 Auto speed, slow to fast
Sound Sensitivity
(When Ch. 7 is 235–255)
000
ó
010
Sound sensitivity off
011 ó255 Sound sensitivity, low to high
3-CH
Channel
Function
Value
Percent/Setting
1
Red
000 ó255 0–100%
2
Green
000
ó
255
0–100%
3
Blue
000 ó255 0–100%

Freedom Stick User Manual Rev. 3 Page 15 of 22
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode to a DMX string
connected to a DMX controller. Products in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Automatic
Programs
To run the Freedom Stick in automatic mode, follow the instructions below:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> and <DOWN> to select an auto program (P1–35).
4. Press <ENTER>.
For P 22–27:
5. Use <UP> or <DOWN> to select the first color (1--r, 1-rg, 1--g, 1-gb, 1--b, 1-rb,
1rgb, or 1OFF).
6. Press <ENTER>.
7. Use <UP> or <DOWN> to select the second color (2--r, 2-rg, 2--g, 2-gb, 2--b, 2-rb,
2rgb, or 2OFF).
8. Press <ENTER>.
For each program 22–27, color 1 and color 2 cannot be assigned the same color.
Auto-
Program
Speed
To change the auto-program speed on the Freedom Stick, do the following:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> and <DOWN> to increase or decrease the program speed (S1–100).
3. Press <ENTER>. The product will return to the last selected mode.
Sound-Active
Mode To run the Freedom Stick in sound-active mode, do the following:
1. Press <MENU> repeatedly until Snd shows on the display.
2. Press <ENTER> twice to accept.
The product will only respond to low frequencies of music (bass and drums).
Sound Sensitivity
To change the sound sensitivity on the Freedom Stick, follow the instructions below:
1. Press <MENU> repeatedly until SenS shows on the display.
2. Use <UP> and <DOWN> to increase or decrease the sound sensitivity (u0–100).
3. Press <ENTER>. The product will return to the last selected mode.
Preset Color
Mode
To run the Freedom Stick in preset color mode, follow the instructions below:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> and <DOWN> to select a static color (C1–7).
4. Press <ENTER> twice to accept.
Custom Color
Mixing
To custom mix a static color, follow the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> and one of the following will show on the display:
•r_ _ _ (red)
•g_ _ _ (green)
•b_ _ _ ( blue)
3. Press <ENTER> to cycle through the color settings.
4. When the desired color shows on the display, use <UP> or <DOWN> to increase or
decrease the color value.
5. Repeat steps 3 and 4 until the product outputs as desired.

Page 16 of 22 Freedom Stick User Manual Rev. 3
IRC-6 Infrared
Remote
Control
The Freedom Stick is compatible with the IRC-6 infrared remote control from Chauvet
DJ. To activate IR mode, follow the instructions below:
Individual products:
Each product will respond independently to the IRC-6 remote.
1. Press <MENU> repeatedly until Set appears on the display.
2. Press <ENTER> to accept.
3. Press <UP> or <DOWN> to select ON.
4. Press <ENTER>.
5. Press <MENU> repeatedly until C-- or P – (COLOR/Auto Programs) appears on
the display.
6. Press <ENTER> twice to accept.
Master/Slave multiple products:
Control 1 product with the IRC-6, have all other products respond to the first product.
Master product:
1. Press <MENU> repeatedly until Set appears on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select ON.
4. Press <ENTER>.
5. Press <MENU> repeatedly until S-tr appears on the display.
6. Use <UP> or <DOWN> to select ON.
7. Press <ENTER>.
8. Use <UP> or <DOWN> to select dtCH (DMX Transmit Channel).
9. Press <ENTER>.
10. Use <UP> or <DOWN> to select the transmitting channel that the slave products
are receiving.
11. Press <ENTER>.
12. Press <MENU> repeatedly until C-- or P – (COLOR/Auto Programs) appears on
the display.
13. Press <ENTER> twice to accept.
Slave products:
1. Press <MENU> repeatedly until Set appears in the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until OFF appears on the display.
4. Press <ENTER>.
5. Press <MENU> repeatedly until S-tr appears on the display.
6. Press <ENTER>.
7. Press <UP> or <DOWN> to select ON.
8. Press <ENTER>.
9. Press <UP> or <DOWN> until the display shows drCH (DMX Receive Channel).
[Display should read dr_#]
10. Press <UP> or <DOWN> until the same channel number is shown as used in the
master unit.
11. Press <ENTER>.
12. Press <MENU> repeatedly until SLA appears on the display.
13. Press <ENTER>.
14. Press <UP> or <DOWN> until SLA2 appears on the display.
15. Press <ENTER>.
16. Press <MENU>until 3-CH (3 channel DMX mode).
17. Press <ENTER>.
[Display should read d###]
18. Press <UP> or <DOWN> until display reads D_ _1
19. Press <ENTER>.
This unit will now respond to the master unit that is being controlled by the IRC-6.
20. Repeat the above steps with all remaining slave units. Setting the desired slave #
(1-4) as needed in step 15.
All slave units will now respond to the master unit being controlled by the IRC-6.

Freedom Stick User Manual Rev. 3 Page 17 of 22
IRC-6 Operation
Automatic Mode
Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode:
1. Press <AUTO> on the IRC-6.
2. Press <+> or <–> to choose between the different auto programs.
To adjust the speed of the automatic program:
1. Press <SPEED> on the IRC-6.
2. Press <+> or <–> to increase or decrease the speed of the program.
Sound-Active Mode
Sound-Active mode will enable the product to respond to the music.
To turn on Sound-Active mode:
1. Press <SOUND> on the IRC-6.
To adjust sound sensitivity in Sound-Active mode:
1. Press <SENSITIVITY> on the IRC-6.
2. Press <+> or <–> to increase or decrease the sound sensitivity.
Manual Color Control
To choose a specific color with the IRC-6:
1. Press <MANUAL> on the IRC-6.
2. Press any number between <0>~<9> to choose your color.
To manually control the RGB percentage:
1. Press <MANUAL> on the IRC-6.
2. Press <R> (red), <G> (green), or <B> (blue) to choose your color.
3. Press <+> or <–> to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the total output level:
1. Press <%> on the IRC-6.
2. Press <+> or <–> to increase or decrease the output level.
To adjust the strobe rate of the program:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
To select only fading programs:
1. Press <FADE> on the IRC-6.
2. Press <+> or <–> toselect P 20 or P 21.
To black out the lights:
1. Press <BLACK OUT> on the IRC-6.
This will turn off all the lights until the button is pressed again.
NOTE: The IRC-
6 will not respond to any inputs when Black Out is activated. If the
remote does not respond when a button is pressed, try pressing <BLACK OUT>
. You
may have inadvertently activated Black Out.

Page 18 of 22 Freedom Stick User Manual Rev. 3
Master/Slave
Mode
Master/Slave mode allows a single Freedom Stick
product (the “master”) to control the
actions of one or more Freedom Stick
products (the “slaves”) without the need of a DMX
controller or DMX cables. The master (transmitter) product will be set to operate in either
Stand-Alone mode or with the IRC-
6, while the slave (receiver) products will be set to
operate in Slave mode. Onc
e set and connected, the slave products will operate in
unison or in sequence with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select ON.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select drCH.
6. Press <ENTER>.
7. Select the receiving D-Fi channel, dr 1–16.
8. Press <ENTER>.
9. Press <MENU> repeatedly until SLA shows on the display.
10. Press <ENTER> to accept.
11. Use <UP> or <DOWN> to select SLA1 (first slave), SLA2 (second slave), SLA3
(third slave), or SLA4 (fourth slave).
12. Press <ENTER>.
13. Finish setting and connecting all the slave products.
Master product:
14. Press <MENU> repeatedly until S-tr shows on the display.
15. Press <ENTER>.
16. Use <UP> or <DOWN> to select ON.
17. Press <ENTER>.
18. Use <UP> or <DOWN> to select dtCH.
19. Press <ENTER>.
20. Use <UP> or <DOWN> to select the transmitting channel that the slave products
are receiving.
21. Press <ENTER>.
22. Set the master product to operate either:
•With the IRC-6.
•In Sound-Active mode
or
•In Auto mode. P 29–35 are designed specifically for Master/Slave mode, but all
programs will work.
•Configure all the slave products before configuring the master to transmit.
•Never connect a DMX controller to a D-Fi channel configured for Master/Slave
operation because the controller may interfere with the signals from the
master.

Freedom Stick User Manual Rev. 3 Page 19 of 22
5.MAINTENANCE
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and/or
mechanical wear. To maintain optimum
performance and minimize wear, clean your lighting product
s at least twice a month.
However, be aware that usage and environmental conditions could be contributing
factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

Page 20 of 22 Freedom Stick User Manual Rev. 3
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
6.3 in (161 mm)
6.3 in (161 mm)
61 in (1550 mm)
3.5 lb (1.6 kg)
Note
: Dimensions in inches rounded to the nearest decimal digit.
Power
Parameter
Freedom Stick
External Power Supply
Input Voltage
Fixed
Switching (internal)
Range
15 VDC, 800 mA
100 to 240 VAC, 50/60 Hz
Voltage Selection
Fixed
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
35 W
35 W
Operating Current
0.05 A
0.03 A
Light Source
Type
Power
Lifespan
SMD LED
0.2 W
50,000 hours
Color
Quantity
Current
Tri-color RGB
32
50 mA
Photometrics
Parameter
Value
Strobe Rate
0 to 30 Hz
Coverage Angle
360°
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Convection
DMX
I/O Connectors
Channel Range
3-pin XLR
3, 8, 48 or 50
Ordering
Product Name
Item Code
UPC Number
Freedom Stick
03051130
781462214784