Chauvet Eclipse RGB User manual

LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
CLASSIFIED PER EN/IEC 60825-1:2007
Complies with FDA performance standards
for laser products except for deviations
pursuant to Laser Notice No. 50, dated
June 24, 2007.

Rev. 10 ML 2 Eclipse™ RGB User Manual
TABLE OF CONTENTS
1. BEFORE YOU BEGIN........................................................................................................................................4
LASER EMISSION DATA.................................................................................................................................................................................6
LASER SAFETY LABEL REPRODUCTION............................................................................................................................................................7
LASER COMPLIANCE STATEMENT...................................................................................................................................................................8
2. INTRODUCTION ................................................................................................................................................ 9
PRODUCT OVERVIEW ...................................................................................................................................................................................9
PRODUCT DIMENSIONS.................................................................................................................................................................................9
3. SETUP............................................................................................................................................................. 10
ACPOWER................................................................................................................................................................................................11
MOUNTING ................................................................................................................................................................................................11
PROPER USE.............................................................................................................................................................................................11
4. OPERATING INSTRUCTIONS.......................................................................................................................... 12
CONTROL PANEL OPERATION.......................................................................................................................................................................12
MENU MAP................................................................................................................................................................................................12
CONFIGURATION (DMX) ...............................................................................................................................................................................12
STARTING ADDRESS....................................................................................................................................................................................12
DMX CHANNEL ASSIGNMENTS AND VALUES...................................................................................................................................................13
CONFIGURATION (STANDALONE)...................................................................................................................................................................14
AUTOMATIC MODE......................................................................................................................................................................................14
SOUND-ACTIVE MODE.................................................................................................................................................................................14
LEDCOLOR MIXING ...................................................................................................................................................................................14
LEDCOLOR FADING...................................................................................................................................................................................14
MASTER/SLAVE MODE ................................................................................................................................................................................15
TECHNICAL SPECIFICATIONS.........................................................................................................................................................................16
RETURNS ..................................................................................................................................................................................................17
1. ANTES DE EMPEZAR...................................................................................................................................... 18
INSTRUCCIONES DE SEGURIDAD....................................................................................................................................................................19
REPRODUCCION DE LA ETIQUETA DESEGURIDAD DEL LASER.............................................................................................................................21
DATOS DEEMISIÓN LÁSER...........................................................................................................................................................................22
DECLARACIÓN DE CONFORMIDAD LÁSER........................................................................................................................................................22
2. INTRODUCCIÓN.............................................................................................................................................. 23
VISIÓN GENERAL DEL PRODUCTO..................................................................................................................................................................23
DIMENSIONES DEL PRODUCTO......................................................................................................................................................................23
3. INSTALACIÓN................................................................................................................................................. 24
CORRIENTE ALTERNA..................................................................................................................................................................................25
MONTAJE..................................................................................................................................................................................................25
USO ADECUADO.........................................................................................................................................................................................25
4. INSTRUCCIONES DE FUNCIONAMIENTO ...................................................................................................... 26
FUNCIONAMIENTO DEL PANELDECONTROL.......................................................................................................................................................26
MAPA DE MENÚ..........................................................................................................................................................................................26
CONFIGURACIÓN (DMX)..............................................................................................................................................................................26
DIRECCIÓN DE INICIO...................................................................................................................................................................................26
ASIGNACIONES DE CANAL Y VALORES DMX....................................................................................................................................................27
CONFIGURACIÓN (INDEPENDIENTE)................................................................................................................................................................28
MODOAUTOMÁTICO....................................................................................................................................................................................28
MODOACTIVO POR SONIDO .........................................................................................................................................................................28
MEZCLA DE COLOR LED..............................................................................................................................................................................28
FADING DE COLOR LED...............................................................................................................................................................................28
MODOMAESTRO/ESCLAVO .........................................................................................................................................................................29
ESPECIFICACIONES TÉCNICAS ......................................................................................................................................................................29
DEVOLUCIONES..........................................................................................................................................................................................30

Eclipse™ RGB User Manual 3 Rev.10 ML
1. AVANT DE COMMENCER ............................................................................................................................... 31
CE QUI EST COMPRIS ..................................................................................................................................................................................31
INSTRUCTIONS RELATIVES AU DEBALLAGE......................................................................................................................................................31
RECLAMATIONS..........................................................................................................................................................................................31
CONVENTIONS DE CE MANUEL......................................................................................................................................................................31
SYMBOLES ................................................................................................................................................................................................31
CONSIGNES DE SECURITE............................................................................................................................................................................32
AVERTISSEMENT BOITIER NONVERROUILLABLE..................................................................................................................................................32
CONSIGNES DE SECURITE RELATIVES AU LASER..............................................................................................................................................33
REPRODUCTIONS DES ÉTIQUETTES ENMATIERE DESECURITE DES APPAREILS LASER...........................................................................................34
DONNEES D'ÉMISSION LASER.......................................................................................................................................................................35
DECLARATION DE CONFORMITE DU LASER......................................................................................................................................................35
2. INTRODUCTION .............................................................................................................................................. 36
VUE D'ENSEMBLE DU PRODUIT......................................................................................................................................................................36
DIMENSIONS DE L'APPAREIL .........................................................................................................................................................................36
3. CONFIGURATION............................................................................................................................................ 37
4. INSTRUCTIONS DE FONCTIONNEMENT........................................................................................................ 39
CONFIGURATION (DMX)..............................................................................................................................................................................39
ADRESSE DE DEPART..................................................................................................................................................................................39
VALEURS ET ASSIGNATIONS DE CANAUX DMX................................................................................................................................................40
CONFIGURATION (AUTONOME)......................................................................................................................................................................41
MODE AUTOMATIQUE..................................................................................................................................................................................41
MODE MUSICAL..........................................................................................................................................................................................41
MELANGE DE COULEURS LED......................................................................................................................................................................41
FONDU DE COULEUR LED............................................................................................................................................................................42
MODE MAITRE/ESCLAVE.............................................................................................................................................................................42
SPECIFICITES TECHNIQUES ..........................................................................................................................................................................43
RENVOIS...................................................................................................................................................................................................43
CONTACT US.............................................................................................................................................................................................44

Rev. 10 ML 4 Eclipse™ RGB User Manual
1.BEFORE YOU BEGIN
What Is
Included
•Eclipse™ RGB
•Power Cable •Warranty Card •User Manual
Unpacking
Instructions Immediately upon receipt, carefully unpack this product and check the box to make sure
you have received all the parts indicated above in good condition.
Claims
If the container or the material inside the container (this product and any other
accessory included) appears damaged from shipping, or shows signs of mishandling,
notify the carrier immediately, not CHAUVET®, upon receipt of the damaged
merchandise. Failure to do so in a timely manner may invalidate your claim with the
carrier. In addition, retain the container and all the packing material for inspection.
For other issues such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of receiving the
merchandise.
Manual
Conventions
CHAUVET® manuals use the following conventions to differentiate certain types of
information from the regular text.
Convention
Meaning
<Menu> A key to be pressed on the product’s control panel
1~512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified (for example, showing the
operating mode/current status)
MENU >
Settings
A sequence of menu options to be followed
ON
A value to be entered or selected
Symbols
This manual uses the following icons to indicate information that requires special
attention on the part of the user.
Symbols
Meaning
Critical installation, configuration or operation information.
Failure to comply with this information may render the product
partially or completely inoperative, cause damage to the
product or cause harm to the user.
Important installation or configuration information. Failure to
comply with this information may prevent the product from
functioning correctly.
Useful information.

Eclipse™ RGB User Manual 5 Rev.10 ML
Safety Notes
Please read the following notes carefully because they include important
safety information about the installation, usage, and maintenance of this
product.
•Keep this User Manual for future consultation. If you sell this product to another user,
be sure that they also receive this document.
•Always make sure that the voltage of the outlet to which you are connecting this
product is within the range stated on the decal or rear panel of the product.
•
This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•Always install this product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect this product from the power source before cleaning it or replacing
fuse.
•Make sure to replace the fuse with another of the same type and rating.
•If mounting it overhead, always secure this product to a fastening device using a
safety chain.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this
product at higher temperatures.
•In the event of a serious operating problem, stop using the unit immediately. Never
try to repair the unit. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center.
•Never connect this product to a dimmer pack.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Never carry a product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•Always avoid direct eye exposure to the light source when this product is on.
•Lasers can be hazardous and have unique safety considerations. Permanent eye
injury and blindness is possible if lasers are used incorrectly. Pay close attention to
each safety statement in this User Manual. Read all instructions carefully BEFORE
operating this device.
Non-
Interlocked
Housing
Warning
•This unit contains high power laser devices internally.
•Do not open the laser housing, due to potential exposure to unsafe levels of laser
radiation.
•The laser power levels, accessible if the unit is opened, can cause instant blindness,
skin burns, and fires.
Laser Safety
Notes STOP AND READ ALL THE LASER SAFETY NOTES BELOW
Laser Light is different from any other light sources with which you may be familiar. The
light from this product can potentially cause eye injury if not set up and used properly.
Laser light is thousands of times more concentrated than light from any other kind of light
source. This concentration of light can cause instant eye injuries, primarily by burning the
retina (the light sensitive portion at the back of the eye). Even if you cannot feel “heat”
from a laser beam, it can still potentially injure or blind you or your audience. Even very
small amounts of laser light are potentially hazardous even at long distances. Laser eye
injuries can happen quicker than you can blink.
It is incorrect to think that because these laser entertainment products split the laser into
hundreds of beams that the laser beam is scanned out in high speed, that an individual
laser beam is safe for eye exposure. This laser product uses dozens of milliwatts of laser
power (Class 3B levels internally) before it splits into multiple beams (Class 3R levels).
Many of the individual beams are potentially hazardous to the eyes.
It is also incorrect to assume that because the laser light is moving, it is safe. This is not
true. Nor, do the laser beams always move. Since eye injuries can occur instantly, it is
critical to prevent the possibility of any direct eye exposure. In the laser safety regulation,
it is not legal to aim Class 3R lasers in areas which people can get exposed. This is true
even if it is aimed below people’s faces, such as on a dance floor.

Rev. 10 ML 6 Eclipse™ RGB User Manual
•Do not operate the laser without first reading and understanding all safety and
technical data in this manual.
•Always set up and install all laser effects so that all laser light is at least 3 meters
(9.8 ft) above the floor on which people can stand. See “Proper Usage” section later
in this manual.
•
After set up, and prior to public use, test laser to ensure proper function. Do not use if
any defect is detected. Do not use if laser emits only one or two laser beams rather
than dozens/hundreds, as this could indicate damage to the diffraction grating optic,
and could allow emission of higher laser levels above Class 3R.
•Do not point lasers at people or animals.
•Never look into the laser aperture or laser beams.
•Do not point lasers in areas in which people can potentially get exposed, such as
uncontrolled balconies, etc.
•Do not point lasers at highly reflective surfaces, such as windows, mirrors and shiny
metal. Even laser reflections can be hazardous.
•Never point a laser at aircraft, this is a federal offense.
•Never point un-terminated laser beams into the sky.
•Do not expose the output optic (aperture) to cleaning chemicals.
•Do not use laser if the laser appears to be emitting only one or two beams.
•Do not use the laser if the housing is damaged, open, or if the optics appear
damaged in any way.
•Never open the laser housing. The high laser power levels inside of the protective
housing can start fires, burn skin and will cause instant eye injury.
•Never leave this device running unattended.
•The operation of a class 3R laser show is only allowed if the show is controlled by a
skilled and well-trained operator, familiar with the data included in this manual.
•The legal requirements for using laser entertainment products vary from country to
country. The user is responsible for the legal requirements at the location/country of
use.
•Always use appropriate lighting safety cables when hanging lights and effects
overhead.
LASER EXPOSURE WARNING
LASER LIGHT AVOID DIRECT EYE EXPOSURE
Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1
Standard “For Safe Use of Lasers,” available from www.laserinstitute.org. Many local governments,
corporations, agencies, military, and others, require all lasers to be used under the guidelines of
ANSI Z136.1. Laser Display guidance can be obtained via the International Laser Display
Association, www.laserist.org.
Laser Emission Data
Laser Classification
Class 3R
Red Laser Medium
LD GaAlAs 650nm, typical
Green Laser Medium DPSS Nd:YVO4, 532nm
Beam Diameter
<5mm at aperture
Pulse Data
All pulses < 4Hz (>0.25sec)
Divergence (each beam)
<2 mrad
Divergence (total light)
<160 degrees
Laser Power of Each
Beam from Aperture* <5mW
*As measured under IEC measurement conditions for classification.

Eclipse™ RGB User Manual 7 Rev.10 ML
Laser Safety Label Reproduction
LASER HAZARD
WARNING LABEL
LASER APERTURE LABEL
EXPLANATORY,
MANUFACTURER’S ID &
CERTIFICATION LABEL
NON-INTERLOCKED
HOUSING LABEL

Rev. 10 ML 8 Eclipse™ RGB User Manual
Laser Compliance Statement
This laser product complies with EN/IEC 60825-1 Ed 2, 2007-03.
Safety Notes
This device was shipped in perfect condition. In
order to maintain this condition and to
ensure safe operation, follow the safety instructions and warning notes written in this
manual. Every person involved with installation and maintenance of this device has to:
Be qualified.
Follow the instructions in this manual.
CAUTION! Be careful when operating. DO NOT touch the housing or
wires when the product is on to avoid a dangerous electric shock!
Important! CHAUVET® will not accept liability for any resulting damage caused by the
non-observance of this manual or any unauthorized modification to the device. Any
modifications to the product will void any warranty.
This product is not intended for permanent installation.
DO NOT mount this product within 50 cm of surrounding walls or large obstacles to
allow for ventilation.
Never let the power-cord come into contact with other cables! Handle the power-cord
and all connections with the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power-switch is set to off-position before you connect the device
to the mains. Make sure the power plug is accessible after mounting the device.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check
the device and the power-cord from time to time.
Always disconnect from power before cleaning or changing the fuse.
Never disconnect from power by tugging on the power cord.
It is essential to connect the yellow/green conductor to a ground (earth).
DO NOT attempt any repairs. The electric connection, repairs, and servicing must be
carried out by a certified technician.
Do not switch the fixture on and off in short intervals as this will reduce the laser diode
life.
Use fuses of same type and rating only.
The ambient temperature must be between 10°C to 40°C. Do not operate at
temperatures outside this range.
If the product has been exposed to drastic temperature fluctuations, do not switch it
on immediately. The arising water condensation might damage the product. Leave
the device switched off until it has reached the ambient temperature.
Do not shake the device. Avoid brute force when mounting or operating the product.
When choosing the mounting location, make sure the product is not exposed to
extreme heat, moisture, or dust.
Keep cables clear of vehicles and people. Otherwise you endanger your own and the
safety of others!
ALWAYS use a safety cable attached to the safety eye hook when mounting the
product overhead.
Use the original packaging when transporting.
Unauthorized modifications are forbidden for safety reasons!
CAUTION! Operate the device only after having familiarized yourself with its
functions. Do not permit operation by unqualified persons. Most damages are the
result of unprofessional operation.
CAUTION! DO NOT operate this device in ways not specified in this User Manual.
Failure to follow the guidance in this manual will void the warranty, may damage the
product, and injure the user or the audience.

Eclipse™ RGB User Manual 9 Rev.10 ML
2.INTRODUCTION
Product Overview
Fuse Holder
Power Switch
Bracket Adjustment Knobs
Control Panel
DMX In/Out
Power In/Out
Mounting Bracket
Laser Aperture
LED Output

Rev. 10 ML 10 Eclipse™ RGB User Manual
Product Dimensions
Bracket moves 360°
for versatile mounting

Eclipse™ RGB User Manual 11 Rev.10 ML
3.SETUP
AC Power
This product has an auto-ranging power supply that can accommodate a wide range of input
voltages. The only thing necessary to do before powering on the unit is to make sure the line
voltage you are applying is within the range of accepted voltages. This product will
accommodate between 100~240V AC 50/60 Hz. All products must be powered directly off a
switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel is used solely for a 0 to 100% switch.
Mounting
Orientation
This product may be mounted in any safe position, provided there is adequate room
for ventilation.
Rigging
It is important never to obstruct the fan or vents pathway. Mount the product using, a
suitable “C” or “O” type clamp. Adjust the angle of the product
by loosening both
knobs and tilting the product. After finding the desired position, retighten both knobs.
When selecting installation location, take into consideration access and routine
maintenance.
Safety cables must always be used.
Never mount in places where the product will be exposed to rain, high humidity,
extreme temperature changes or restricted ventilation.
Proper Use
This product is for overhead mounting only. For safety purposes, CHAUVET®
recommends mounting your lighting effect products on steady elevated platforms or
sturdy overhead supports using suitable hanging clamps. In all cases, you must use
safety cables. Yo
u can obtain appropriate mounting hardware from your lighting
vendor.
International laser safety regulations require that laser products must be operated in
the fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation
between
the floor and the lowest laser light vertically. Additionally, 3 meters of
horizontal separation is required between laser light and audience or other public
spaces.
CAUTION - USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THA
N THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE

Rev. 10 ML 12 Eclipse™ RGB User Manual
4.OPERATING INSTRUCTIONS
Control
Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display. Please refer to the Product Overview to see the button locations
on the control
panel.
Button Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
Menu Map
Mode
Programming Steps
Description
Automatic
Programs
AuF
Automatic Mode, Fast
AuS Automatic Mode, Slow
Sou
Sound Active Mode
rdn Random Effect Mode
Sound
Sensitivity S 0 S 0-S 9 Adjust sound sensitivity for Sound-Active Mode
Manual LED
Control LEd
rgb
(r 0-r 9)
(g 0-g 9)
(b 0-b 9)
(Sr0-Sr9)
Manually adjust the LED color and strobe rate
FdE
(Sp0-Sp9) Manually adjust the LED color fade speed
DMX
Addressing
001 001-501 Set DMX starting address
Slave Mode
SLA
Sets Slave Mode
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting
Address
When selecting a starting DMX address, always consider the number of DMX channels the
selected DMX mode uses. If you choose
a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Eclipse™ RGB uses up to 12 DMX channels in its 12-channel DMX mode, which
defines the highest configurable address to 501.
If you are not familiar with the DMX protocol, download the DMX Primer
from the
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU> repeatedly until 001 shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.

Eclipse™ RGB User Manual 13 Rev.10 ML
DMX Channel Assignments and Values
12-CH
Channel Function Value Setting
1 Auto Mode
000 049
DMX Mode
050 099
Automatic Slow
100 149
Automatic Fast
150 199
Sound Active
200 255
Random Effect
2 Color
000 004
Blackout
005 028
Red
029 056
Green
057 084
Red + Green
085 112
Red off + Green strobe
113 140
Red strobe + Green off
141 168
Red on + Green strobe
169 197
Red strobe + Green on
198 224
Red + Green strobe
225 255
Red + Green alternating strobe
3 Strobe (laser)
000 004
No function
005 249
Strobe (slow to fast)
250 255
Strobe (sound active)
4 Rotation (laser)
000 004
No function
005 127
Clockwise rotation (slow to fast)
128 133
No function
134 255
Counterclockwise rotation (slow to fast)
5 Vibration
000 004
No function
005 255
Vibration (slow to fast)
6 Flash
000 004
No function
005 255
Flash (slow to fast)
7 Red
000 127
Red
128 169
Fade in (0~100%)
170 209
Fade out (100%~0)
210 255
Alternating fade (100%~0~100%...)
8 Green
000 127
Green
128 169
Fade in (0~100%)
170 209
Fade out (100%~0%)
210 255
Alternating fade (100%~0~100%...)
9 Blue
000 127
Blue
128 169
Fade in (0~100%)
170 209
Fade out (100%~0)
210 255
Alternating fade (100%~0~100%...)
10
Dimmer
000 255
0~100%
11 Strobe (LED)
000 004
No function
005 249
Strobe (slow to fast)
250 255
Strobe (sound active)
12 Rotation (LED)
000 004
No function
005 127
Clockwise rotation (slow to fast)
128 133
No function
134 255
Counterclockwise rotation (slow to fast)

Rev. 10 ML 14 Eclipse™ RGB User Manual
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either Static,
Automatic, or Sound) to a DMX string connected to a DMX controller. Products
in standalone mode may transmit DMX signals that could interfere with the DMX
signals from the controller.
Automatic
Mode
To enable the Automatic modes, do the following:
1. Press <MENU> repeatedly until AuF, AuS, Sou, or rdn shows on the display.
2. Press <UP>or <DOWN> to choose AuF (for a fast show), AuS (for a slow show)
or rdn (for a random show).
3. Press <ENTER>.
Sound-Active
Mode
To enable the Sound-Active mode, do the following:
1. Press <MENU> repeatedly until AuF, AuS, Sou, or rdn shows on the display.
2. Press <UP>or <DOWN> to choose Sou.
3. Press <ENTER>.
4. Turn the music on and adjust the microphone sensitivity until the product starts
responding to the beat of the music.
1. To adjust the sound sensitivity of the Sound Active mode, do the following:
1. Press <MENU> repeatedly until S 0 shows on the display.
2. Press <UP>or <DOWN> to choose between no sound activation and high sound
activation (S 0-S 9).
3. Press <ENTER>.
LED Color
Mixing
You are able to manually mix the colors and strobe rate
of the LED portion of the
product. To do so, follow the steps below:
1. Press <MENU> repeatedly until LEd, rGb, or FdE shows on the display.
2. Press <UP>or <DOWN> to choose rGb.
3. Press <ENTER>.
4. Press <UP>or <DOWN> to adjust between full off and on for red (r 0-r 9).
5. Press <ENTER>.
6. Press <UP>or <DOWN> to adjust between full off and on for green (G 0-G 9).
7. Press <ENTER>.
8. Press <UP>or <DOWN> to adjust between full off and on for blue (b 0-b 9).
9. Press <ENTER>.
10. Press <UP>or <DOWN> to adjust the strobe rate (Sr0-Sr9).
11. Press <ENTER>.
LED Color
Fading
You are able to manually adjust the fade speed of
the LED portion of the product. To
do so, follow the steps below:
1. Press <MENU> repeatedly until LEd, rGb, or FdE shows on the display.
2. Press <UP>or <DOWN> to choose FdE.
3. Press <ENTER>.
4. Press <UP>or <DOWN> to adjust the fade speed between slow and fast
(SP0-SP9).
5. Press <ENTER>.

Eclipse™ RGB User Manual 15 Rev.10 ML
Master/Slave
Mode
The Master/Slave mode allows a single Eclipse™ RGB unit (the “master”) to control the
actions of one or more Eclipse™ RGB
units (the “slaves”) without the need of a DMX
controller. The master unit will be set
to operate in either Automatic or Sound Active
mode, while the slave units will be set to operate in Slave Mode. Once set and
connected, the slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU> repeatedly until SLA shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to 001.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in either Automatic or Sound mode.
2. Make the master unit the first unit in the DMX daisy chain.
•Configure all the slave units before connecting the master unit to the DMX
daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the
master unit.
•Do not connect more than 31 slave units to the master unit.
•The lasers cannot be turned off. They can be set to a slow strobe.
•At higher rotation speeds, the operation noise may increase from the
product. This is normal.

Rev. 10 ML 16 Eclipse™ RGB User Manual
Technical Specifications
WEIGHT & DIMENSIONS
Length...............................................................................................................................................................................7.7 in (196 mm)
Width ................................................................................................................................................................................9.5 in (241 mm)
Height ...............................................................................................................................................................................6.4 in (162 mm)
Weight ...............................................................................................................................................................................3.7 lbs (1.7 kg)
POWER
Autoswitching power supply...............................................................................................................................100~240 VAC 50/60 Hz
Fuse....................................................................................................................................................................T 1 A 250 V (slow-blow)
Power Consumption......................................................................................................................................43 W (0.4 A) max @ 120 V
Power Consumption......................................................................................................................................49 W (0.6 A) max @ 230 V
Power Output ...........................................................................................................................22 units max @ 120 V, 42 units @ 230V
LIGHT SOURCE
LED................................................................................................................................................8 W (700 mA x 3) tri-color 50,000 hrs
LASER
Green diode...................................................................................................................................................................... 532 nm/40 mW
Red diode.......................................................................................................................................................................650 nm/100 mW
Laser Type ...................................................................................................................................................................................... DPSS
Cooling ...................................................................................................................................................................................Fan Cooled
RANGE
Coverage Angle ...................................................................................................................................................................................70°
THERMAL
Maximum ambient temperature.........................................................................................................................................104° F (40° C)
ORDERING INFORMATION
Eclipse™ RGB ...................................................................................................................................................................ECLIPSERGB
WARRANTY INFORMATION
Warranty...............................................................................................................................................................2-year limited warranty

Eclipse™ RGB User Manual 17 Rev.10 ML
Returns
Call the corresponding CHAUVET® Tech Support office and request a Return Merchandise
Authorization (RMA) number before shipping the product. Be prepared to provide the model
number, serial number, and a brief description of the cause for the return.
You must send the merchandise prepaid, in its original box, and with its original packing and
accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product returned
without an RMA number.
DO NOT write the RMA number directly on the box. Instead, write it on a properly affixed
label.
Note: If you are given an RMA #, please include the following information on a piece of
paper inside the box:
•Your name
•Your address
•Your phone number
•The RMA #
•A brief description of the symptoms
CHAUVET® reserves the right to use its own discretion to repair or replace product(s). FedEx
packing or double-boxing are recommended.
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of record
and follow their instructions on how to return CHAUVET® products to them. Visit
www.chauvetlighting.com for contact details.

Rev. 10 ML 18 Eclipse™ RGB Manual de Usario
1.ANTES DE EMPEZAR
¿Qué va
Incluido?
•Scorpion™ Storm RGB EU
•Cable de alimentación •Tarjeta de garantía •Manual de usuario
Reclamaciones
Desembale el producto inmediatamente y compruebe la caja para asegurarse de que
todas las
piezas están presentes y en buen estado. Si la caja o los contenidos
parecen dañados por el transporte, notifíqueselo al transportista inmediatamente, no a
CHAUVET®. Guarde la caja y todo el material de embalaje para su inspección. Para
partes que falten
o daños no relacionados con el transporte, presente una
reclamación a CHAUVET® en el plazo de 7 días de la recepción del producto.
Instrucciones
de Desembalaje
Inmediatamente después de recibirlo, desempaquete este producto y compruebe el
contenedor para
asegurarse de que ha recibido las partes que se indican arriba en
buenas condiciones.
Exención de
Responsabilidad
Este manual está sujeto a cambio sin previo aviso. CHAUVET® no asume
responsabilidad de ningún tipo por cualquier error u omisión y se reserva el derecho a
hacer correcciones sin previo aviso. Descargue la última versión de este manual de
www.chauvetlighting.com.
© Copyright 2012 CHAUVET® Todos los derechos reservados.
Impreso en la R.
P. China. Publicación en formato electrónico por CHAUVET® en EE.UU.
Reclamaciones
Si el contenedor o el material dentro del contenedor (este producto y cualquier
accesorio incluido) parecen dañados a causa del transporte o muestran signos de
manipulación inadecuada, notifíqueselo inmediatamente al transportista, y no a
CHAUVET®, en el momento de recibir la mercancía dañada.
Si no lo hace
oportunamente, puede quedar invalidada su reclamación al transportista. Además,
guarde la caja y todo el material de embalaje para su inspección.
Para otras incidencias, como componentes o piezas que
falten, daños no
relacionados con el transporte o daños no evidentes, presente una reclamación a
CHAUVET® en el plazo de siete (7) días de la recepción de la mercancía.
Convenciones
del Manual
Los manuales de CHAUVET® usan las siguientes convenciones para diferenciar
ciertos tipos de información del texto normal.
Convención
Significado
<Menu> Una tecla que se tiene que pulsar en el panel de
control del producto
1~512
Un rango de valores
50/60 Un conjunto de valores de los cuales solo se pude
escoger uno
Configuración Una opción de menú que no se modifica (por ejemplo,
mostrar el modo de funcionamiento/estado actual)
MENÚ > Configuración Una secuencia de opciones de menú que ha de
seguirse
ON
Un valor que se tiene que introducir o seleccionar
Símbolos
Este manual utiliza los siguientes iconos para indicar qué información requiere
especial atención por parte del usuario.
Símbolo
Significado
Información crítica sobre instalación, configuración o
funcionamiento. Este producto podría no funcionar en
parte o totalmente, averiarse o causar daños al
usuario si no se sigue esta información.
Instalación o información de configuración importante.
Hacer caso omiso puede provocar que el producto no
funcione correctamente.
Información útil.

Eclipse™ RGB Manual de Usuario 19 Rev. 10 ML
Instrucciones
de Seguridad Las notas siguientes incluyen información importante de seguridad
sobre la instalación, uso y mantenimiento de este producto.
•Guarde este Manual de Usuario para futuras consultas. Si vende este producto
a otro usuario, asegúrese de que este recibe también el presente documento.
•Asegúrese siempre de que la tensión del enchufe al que conecte este producto
está en el rango establecido en el grabado o en el panel posterior del producto.
•¡Este producto es para uso en interiores solamente! Para evitar riesgos de
incendio o descarga, no exponga este producto a la lluvia o la humedad.
•Asegúrese de que no hay materiales inflamables cerca de la unidad cuando
esté en funcionamiento.
•Instale siempre este producto en una ubicación con ventilación adecuada, al
menos a 20'' (50 cm) de superficies adyacentes. Asegúrese de que no se han
bloqueado las ranuras de ventilación.
•Desconecte siempre este producto de la fuente de alimentación antes de
limpiarlo o cambiar el fusible.
•Asegúrese de sustituir el fusible con otro del mismo tipo y categoría.
•Si lo monta en alto, asegure siempre este producto a un dispositivo de
seguridad usando una cadena de seguridad.
•La máxima temperatura ambiente (Ta) es de 104º F (40º C). No haga funcionar
este producto a temperaturas más altas.
•En caso de un problema grave de funcionamiento, deje de usar la unidad
inmediatamente. Nunca intente reparar la unidad. Las reparaciones llevadas a
cabo por personal no cualificado pueden provocar averías o funcionamiento
defectuoso. Póngase en contacto con el centro de asistencia técnica
autorizado más cercano.
•Nunca conecte este producto a un regulador de intensidad.
•Asegúrese de que el cable de alimentación no está retorcido ni estropeado.
•Nunca desconecte el cable de alimentación agarrando o tirando del cable.
•Nunca arrastre un producto agarrando por el cable de alimentación o por
cualquier parte móvil. Use siempre el soporte de montaje/colgar para el
manejo.
•Evite siempre la exposición directa de los ojos a la fuente de luz mientras este
producto esté encendido.
•Los láseres pueden ser peligrosos y tienen consideraciones de seguridad
particulares. Puede producirse lesión ocular permanente y ceguera si los
láseres se usan incorrectamente. Ponga máxima atención a todos los
COMENTARIOS y ADVERTENCIAS de seguridad de este manual de usuario.
Lea atentamente todas las instrucciones ANTES de poner en funcionamiento
este dispositivo.
•Evite el contacto directo de los ojos con la luz del láser. Nunca exponga
intencionadamente sus ojos o los de otras personas a la luz directa del láser.
•Este producto láser puede causar lesiones oculares al instante, o ceguera, si la
luz del láser incide directamente en los ojos.
•Es ilegal y peligroso alumbrar con este láser zonas de espectadores en las que
el público u otro personal pueda recibir rayos láser o reflejos de su brillo
directamente en los ojos.
•En los EEUU es un delito federal dirigir cualquier láser hacia un avión.
•El uso de controles, ajustes o procedimientos de operación distintos a los
especificados aquí pueden causar exposición peligrosa a la radiación.
•No hay piezas reparables por el usuario dentro de la unidad. No abra la
carcasa ni intente ninguna reparación por sí mismo. En el caso improbable de
que su unidad requiera reparación, póngase en contacto con su distribuidor
más cercano.
•Evite el contacto directo de los ojos con la luz del láser. Nunca exponga
intencionadamente sus ojos o los de otras personas a la luz directa del láser.
Advertencia
Sobre Carcasa
no Enclavada
•Esta unidad contiene internamente dispositivos láser de alta potencia.
•No abra la carcasa del láser, debido a la potencial exposición a niveles no
seguros de radiación láser.
•Los niveles de láser a los que se tiene acceso si se abre la unidad pueden
causar ceguera instantánea, quemaduras en la piel e incendios.

Rev. 10 ML 20 Eclipse™ RGB Manual de Usuario
Notas de
Seguridad Sobre
Láser
DETÉNGASE Y LEA TODAS LAS NOTAS DE SEGURIDAD
SOBRE EL LÁSER SIGUIENTES
La luz láser es diferente de cualquier otra fuente de luz que usted conozca. La luz
de este producto puede potencialmente causar lesión ocular si el producto no se
instala y usa adecuadamente. La luz láser es miles de veces más concentrada que
la luz de cu
alquier otro tipo de fuente. Esta concentración de luz puede causar
lesiones instantáneas en el ojo, fundamentalmente por quemadura de la retina (la
zona sensible a la luz en la parte posterior del ojo). Aunque usted no pueda sentir
el “calor” de un haz de láser, este puede aún potencialmente lesionar o cegarle a
usted o al público. Incluso cantidades de luz láser muy pequeñas son
potencialmente peligrosas, incluso a largas distancias. Las lesiones oculares por
láser pueden ocurrir más rápido de lo que se tarda en parpadear.
No es correcto pensar que porque estos productos recreativos de láser dividen el
láser en cientos de haces, o porque el haz de láser se lanza a alta velocidad, es
segura la exposición del ojo a cualquier haz individual de láser. Este pro
ducto de
láser utiliza docenas de milivatios de potencia láser (niveles clase 3B internamente)
antes de dividirlo en múltiples haces (niveles clase 3R). Muchos de los haces
individuales son potencialmente peligrosos para los ojos.
También es incorrecto asumir que porque la luz láser está en movimiento, es segura.
Esto no es cierto. Ni tampoco que los haces de láser se mueven siempre. Puesto
que las lesiones oculares pueden producirse instantáneamente, es crítico prevenir la
posibilidad de cualquier exposición directa al ojo. En las disposiciones de seguridad
láser, no es legal apuntar con láseres Clase 3R hacia áreas en las que las personas
puedan quedar expuestas. Esto se aplica incluso si se apunta por debajo de las
caras de la gente, por ejemplo hacia la pista de baile.
•No ponga en funcionamiento el láser sin primero leer y comprender todos los
datos técnicos y de seguridad de este manual.
•Ubique e instale todos los efectos láser siempre de forma que toda la luz láser
está al menos a 3 m (9,8 pies) sobre el nivel del suelo en el que se encuentra la
gente. Vea el apartado "Uso adecuado" más adelante en este manual.
•Después de la instalación, y antes de su uso público, pruebe el láser para
asegurarse de que funciona adecuadamente. No lo use si detecta cualquier defecto.
No lo use si el láser emite solo uno o dos haces de láser en lugar de docenas o
centenares, pues esto podría indicar una avería en la óptica de la rejilla de
difracción, y podría permitir la emisión de niveles de láser por encima de la clase 3R.
•No apunte con láser a personas o animales.
•Nunca mire a la apertura del láser o a los haces de láser.
•No apunte con el láser hacia áreas en las que las personas pudieran quedar
expuestas, como balcones sin vigilancia, etc.
•No apunte con láseres a superficies muy reflectantes como ventanas, espejos y
metal pulido. Incluso los reflejos del láser pueden ser peligrosos.
•Nunca apunte con el láser a un avión, pues constituye un delito federal.
•Nunca apunte hacia el cielo con haces láser sueltos.
•No exponga la óptica de salida (apertura) a productos de limpieza químicos.
•No utilice el láser si parece estar emitiendo solo uno o dos haces.
•No use el láser si la carcasa está averiada o abierta, o si la óptica parece
dañada de cualquier modo.
•Nunca abra la carcasa del láser. Los altos niveles de potencia láser dentro de la
carcasa protectora pueden originar incendios, quemaduras en la piel y causarán
lesiones oculares al instante.
•Nunca deje este dispositivo en funcionamiento sin vigilancia.
•El funcionamiento de un láser de espectáculo de Clase 3R solo se permite si el
espectáculo es controlado por un operador experimentado y bien formado,
familiarizado con los datos contenidos en este manual.
•Los requisitos legales para usar productos de láser recreativo varían de un país
a otro. El usuario es responsable de los requisitos legales del lugar/país en que
lo utilice.
•Use siempre los cables de seguridad apropiados cuando cuelgue estas luces y
efectos sobre las cabezas.