Cinderella BUILD IN BOX TRAVEL User manual

BUILD IN BOX TRAVEL
Installation instruction
English
Document number: InD-000011
Revision number: 02
Build in box Travel Instruction | 11.11.2022

1. GENERAL SECTION
1.1 INTRODUCTION
Build in box Travel is designed to ease the installation of a Cinderella Travel. It is an alternative to installing the
appliance into walls or cabinets.
2. INSTALLATION
2.1 PLANNING AND POSITIONING
Position the appliance and Build in box where you intend to install it, the appliance should have a little gap to the
wall and the Build in box ush to the wall. Plan out where you want the inlet and outlet air pipes to go, as well as
the control panel to be located.
2.2 INSTALLATION OF INLET AIR
The inlet air pipe is exible with a
diameter of 80 mm. Drill a hole to
a point where the toilet has access
to fresh air. The most common way
to install inlet air in a caravan is
straight down from the appliance.
Use the end cap delivered in the
travel installation kit on the end of
the pipe.
BUILD IN BOX TRAVEL QTY
1Box 1
2Top 1
3Pipe cover 2
4Bracket 1
5Screw plug 12
6Installation instruction 1
2.4 FASTENING THE APPLIANCE TO THE BUILD IN BOX
Your Cinderella Travel appliance should be fastened to the box by screwing the 10 screws through the metal
ange, then the plastic trim and nally into the box. The screw holes on the ange can be seen after removing
the shell. Make sure that the metal ange is the outermost part, then the plastic trim, and then the box.
2.3 INSTALLATION OF OUTLET AIR
The outlet air pipe is exible with a diameter of 65 mm. There should also
be Armaex insulation around the pipe (part of the installation kit), making
the diameter 90 mm (Illustration 2). Consider where you want the outlet air
pipes to be installed before drilling any holes. The outlet air pipes can be
hidden inside cabinets or similar, or the included pipe covers can be used.
See sect. 2.7 for instructions on how to install these.
3
6
1
25
4
1.2 TOOLS NEEDED
• 16x screws
• Screwdriver
• Hole saw/bore 22mm
• Handsaw or electric saw (optional)
• Hole saw/bore 26mm (optional)
1.3 WHAT IS INCLUDED IN THE KIT

2.5 FASTENING THE BUILD IN BOX TO THE WALL
The lid is designed to not be fastened by screws,
this is to give easy access to the backside of the
appliance if needed. Simply slide the lid on top
of the box. If the outlet air pipe is to go through
the lid, cut away a segment of the material big
enough for the pipe to go through. Make sure it
is not so big that the pipe cover won’t cover the
cutout, the pipe and insulation has a diameter
together of around 90 mm. The pipe covers will
help hold the lid in place. If the lid becomes too
loose and starts moving, use a piece of tape or
removable adhesive to hold the lid in place.
2.7 FASTENING THE PIPE COVERS
The pipe covers are used to hide the pipes. Simply cut the pipe covers to
the necessary length. If possible, try to avoid cutting away the holes for the
screw plugs. Please read section 2.8 before making any cuts.
When fastening the pipe covers to the wall, place the bottom pipe cover
on top of the lid, so that it pushes down on the lid just a little bit to hold it
in position. Fasten them the same way to the wall as done with the box.
Insert the screw plugs into the holes on the side
of the box, with the screw hole facing towards
the wall. Use screws through the plugs to fasten
the box to the wall. Use screws that are long
enough to reach the wall. Make sure not to
tighten the screws too hard as the box walls
may start to curve.
2.6 MOUNTING THE LID
2.8 FASTENING THE BRACKET
The bracket can be fastened to the ceiling outside of the pipe covers to
hide imperfections in the cut, and also to hold the pipe covers in place if
the hole for the screw plug has been removed.
2.9 FASTENING THE CONTROL PANEL
The control panel can be installed anywhere, so long as the cable is long enough. The panel can be installed
as shown in the pictures below, or in another position to your liking. Make a 22mm hole for the cable to pass
through. Note that the cable is not positioned in the center of the control panel, so be mindful of where you drill
the hole.
2.10 FASTENING THE APPLIANCE TO THE FLOOR
After the inlet and outlet pipes have been installed, the appliance should be fastened to the oor. Remove the
outer shell and ash container from your Cinderella Travel and use 4 screws to fasten the appliance to the oor.

Cinderella Eco Group AS
Sjøvikvegen 67, NO-6475 Midsund, Norway
www.cinderellaeco.com
CINDERELLA’S GLOBAL PRESENCE
North America
Greenland
Africa China
South Korea
Nordic Region
Europe
Oceania