CIS VCC-F32U29CL Installation instructions

VCC-F32U29CL Rev. 900-513-31-01
En
g
lish
UXGA Color Camera
72MHz Pixel Clock Camera Link
VCC-F32U29CL
Product Specification
& Operation Manual
CIS Corporation
©2007 CIS Corporation. All rights reserved.
1

VCC-F32U29CL Rev. 900-513-31-01
©2007 CIS Corporation. All rights reserved.
2
Table of Contents
1. Scope of Application ..................................................................................................................... 3
2. Notice ......................................................................................................................................... 3
3. Product Outline ............................................................................................................................ 3
4. System Connection Diagram.......................................................................................................... 4
5. Specification ................................................................................................................................ 5
5.1. General Specification.............................................................................................................. 5
5.2. Camera Output Signal Specification ......................................................................................... 7
5.3. Camera Link Connector Bit Assignment (Base Configuration)..................................................... 9
5.4. Function Settings ..................................................................................................................10
6. External Connector Pin Assignment...............................................................................................13
6.1. 12 pins Circular Connector HR10-10R-12PA (73)....................................................................13
6.2. 26 Pins Compact Camera Link Compatible Connector (3M) .......................................................13
7. Switch Settings, Adjustment Potentiometer Specifications...............................................................14
7.1. Rear Panel Switch Function 10bit DIP-SW................................................................................14
7.1.1. Shutter Speed Settings （Rear panel SW1: E0, SW2: E1, SW2: E2）..................................14
7.1.2. Operation Mode Settings （Rear panel SW4: MODE0, SW5: MODE1）...................................15
7.1.3. Partial Scan Setting Switch (Rear Panel SW: 6 SCAN) .........................................................16
7.1.4. (Rear Panel SW7: - )........................................................................................................18
7.1.5. RGB / RAW Selection Switch （Rear panel SW8: RGB/RAW）................................................18
7.1.6. RAW 8 bit / 10bit Selection Switch （Rear Panel SW9:8Bit/10Bit）.......................................18
7.1.7. HD / VD Input / Output Selection Switch (Rear panel SW10: IN/OUT) .................................18
7.1.8. WEN （Write Enable）Signal Output..................................................................................18
7.2. 12 Turn Rotary Potentiometer for Manual Gain Adjustment.......................................................18
7.3. Internal Adjustment Switches and Potentiometer Information...................................................19
7.4. HD/VD Trigger Input/Output Circuit of 12pin Circular Connector................................................20
7.5. Remote Interface Function .....................................................................................................21
8. Safety/Quality Standards..............................................................................................................22
9. Durability....................................................................................................................................23
10. Timing Chart .............................................................................................................................24
10.1. Horizontal Synchronous Timing.............................................................................................24
10.2. Vertical Synchronous Timing.................................................................................................25
10.3. Vertical Synchronous Timing (58 fps partial scan mode: initial setting) ....................................26
10.4. Standard Trigger Timing.......................................................................................................27
10.5. Pulse Width Trigger Timing .................................................................................................28
11. Dimensions ...............................................................................................................................29
12. Cases for Indemnity (Limited Warranty) ......................................................................................30
13. Handling Precautions .................................................................................................................31

VCC-F32U29CL Rev. 900-513-31-01
©2007 CIS Corporation. All rights reserved.
3
1. Scope of Application
This is to describe VCC-F32U29CL Camera Link Color CCD Camera. All specifications contained herein
are subject to change without prior notice. Reproduction in whole or in part is prohibited.
2. Notice
The camera must not be used for any nuclear equipments or aerospace equipments with which
mechanical failure or malfunction could result in serious bodily injury or loss of human life.
Our warranty does not apply to damages or defects caused by irregular and/or abnormal use of the
product. Please refer to Clause 13. Handling Precautions.
3. Product Outline
VCC-F32U29CL is a high-resolution industrial color digital video camera module utilizing a 1/1.8 inch PS
IT CCD. 2M CCD image sensor with on-chip micro-lenses realizes high sensitivity and high resolution.
Key Features
□Electronic shutter
Electronic shutter speed switchable by rear panel switch
OFF (1/30s) ～1/10,000s : 8 steps
OFF (1/30s) ～1/1.875s : 5 steps (Slow shutter)
Electronic shutter switchable by trigger pulse width
Approx. 1/2s ～1/10,000s
□Video frame rates
The followings are for both normal mode and trigger mode.
Progressive Scan : 30 fps
Partial Scan (initial setting : 58 fps) : 74 fps ～41 fps (switchable)
□Input trigger
The input trigger inputted during the execution of prior trigger shall be ignored.
Ex. When the shutter speed is set to 1/1,000sec, signal read out period will be over 34.39ms.
(Exposure time 1ms + video out 33.39ms.)
□Camera Link
By use of dedicated cable, VCC-F32U29CL can be connected to Camera Link capture board.

VCC-F32U29CL Rev. 900-513-31-01
4. System Connection Diagram
Camera Power Supply
OUT PUT：DC12.0V
©2007 CIS Corporation. All rights reserved.
4
Camera Link Cable
Camera Link Camera
＊Recommended Ripple Voltage ：under ±500ｍV
(Same ripple voltage applies when supplying power to frame grabber board.)
＊ Camera Output : 26pin Camera Link Connector
Camera Power Supply : 6pin or 12pin Circular Connector
Frame Grabber Board
For Camera Link
Installed
to PC

VCC-F32U29CL Rev. 900-513-31-01
©2007 CIS Corporation. All rights reserved.
5
5. Specification
5.1. General Specification
Item Specification Remarks
Power consumption 4.0 W
Power requirements DC+12V ± 10% (Max voltage not to exceed 15V）
Operation
environment
(Performance Guaranteed) 0℃～+40℃with RH 20～80%
(Operation Guaranteed) -5℃～+45℃with RH 20～80%
Note: No condensation
Storage environment -25 to +60℃with RH 20～80%
Note: No condensation
Mass 140g
Dimension Refer to overall dimension drawing (Clause 11)
(W: 44mm, H: 29mm, D: 71.5mm)
Lens mount C mount（Flange back：17.526mm (fixed）
Back Focus 10.99mm
Optical axis accuracy Image center ≦ ± 0.1 mm
Video output signal Digital RGB 24bit Camera Link
Output
Digital RAW 8bit / 10 bit (Selectable)
Pick up device
1/1.8” Interline Transfer Color CCD
（R,G,B primary color mosaic filter）
ICX274AQ
(SONY)
Progressive
Scan
Total Pixel number; 1628(H) x 1248(V) approx. 2.03M pixels
Effective pixels number; 1620(H) × 1220(V) approx. 1.98M pixels
Unit cell size; 4.4μm(H) × 4.4μm(V) Square pixel
Sync. ＆Trigger
system
(1) Standard operation mode (Int. sync system)
12pin circular
connector
(2) HD/VD Ext. sync.
Frequency allowance ±１% Jitter less than 20ns
(3) Ext. trigger: trigger input port
(Camera Link connector input or 12pin circular connector)
・Standard trigger operation mode
・Trigger pulse width operation mode
・Standard trigger operation mode (Slow shutter)

VCC-F32U29CL Rev. 900-513-31-01
©2007 CIS Corporation. All rights reserved.
6
Item Specification Remarks
Scanning system
Interlace scan
1/30sec Progressive scan （Standard mode）
Horizontal frequency 37.50 KHz 1920 PCLK
Vertical frequency 29.95 Hz 1252 HD
Pixel clock 72 MHz
Partial Scan
V. Scanning Lines Rate V. Effective lines (Initial setting)
Refer to Clause
7.1.3
Off (Full Image) 1,252 Lines 30fps 1,220 Lines
Partial Scan 652 Lines 58fps 482 Lines (Initial)
Min. 508 Lines 74fps 302 Lines Setting range
Max. 924 Lines 41fps 822Lines
Sensitivity More than F5.6 at 2000 lx (at 1/30sec exposure，GAIN 0dB)
Min. illumination F1.4 4 lx (at 1/30sec exposure, GAIN 12dB, VS 50IRE)

VCC-F32U29CL Rev. 900-513-31-01
©2007 CIS Corporation. All rights reserved.
7
5.2. Camera Output Signal Specification
Item Specification Remarks
Horizontal resolution
800 TV lines （RGB output）
1,000 TV lines （RAW output）
Sync. signal I/O
(1) LVAL output: Polarity Negative
(2) FVAL output: Polarity Negative
(3) DVAL output: BLK output (Effective ima
g
e area) Polarity
Positive
Camera Link
Connector
(1) HD/VD input; Polarity Negative （Ext. Sync. mode）
Input signal level 2～5Vp-p
(HD/VD signals: not to contain undesirable noise such as chatterin
g
,
etc.)
(2) HD/VD output; Polarity Negative （Int. sync. mode）
(3) WEN output; Exposure selectable: Single Pulse VD / FVAL
(Ext. trigger mode)
* Refer to Clause 7.4
(I/O circuits for HD / VD / trigger at 12 pins circular connector)
12 pins
circular
connector
(Refer to
address 055)
Trigger input
Input signal; Polarity Selectable (Refer to
address 011)
Input signal level
Input signal level; 2～5Vp-p, TTL input
Trigger signal: not to contain undesirable noise
such as chattering.
12pin circular
connector
CC１input Camera link
connector
Min. Trigger pulse width ≧1HD
Video output signal Setup level : 4 ±2 (Hex) to 8bit video output (00-FF Hex)

VCC-F32U29CL Rev. 900-513-31-01
©2007 CIS Corporation. All rights reserved.
8
Item Specification Remarks
Shutter
(1) Standard mode
OFF(1/30), 1/60, 1/90, 1/120, 1/500, 1/1,000, 1/5,000, 1/10,000 sec (Standard mode)
OFF(1/58), 1/60, 1/90, 1/120, 1/500, 1/1,000, 1/5,000, 1/10,000 sec (Partial scan mode)
(2) The fixed shutter speeds trigger operation with switch control
1/30, 1/60, 1/90, 1/120, 1/500, 1/1,000, 1/5,000, 1/10,000 sec
(Standard mode)
1/58 1/60, 1/90, 1/120, 1/500, 1/1,000, 1/5,000, 1/10,000 sec (Partial scan mode)
(3) Trigger pulse width mode
1/4 ～1/10,000 sec (1H step trigger pulse width control mode)
(4) Standard trigger mode (Slow shutter)
1/30, 1/15, 1/7.5, 1/3.75, 1/1.875 sec
1/58, 1/29, 1/14.5, 1/7.25, 1/3.625 sec
(5) * Jitter between Int. HD & Trigger will cause 1H fluctuation of
exposure time.
T
o avoid the fluctuation, please synchronize
with EXT. HD.
Gain
0dB, +6dB, MANUAL (0～max +12dB)
Performance guaranteed range; 0～+6dB
When gain setting is more than +6dB, noise may become visible
such as Vertical stripes, beat noise, shading, etc.
White Balance 3200゜K, 5600゜K, Manual (2600゜K～9000゜K) RGB output mode
only
γ(Gamma
correction)
OFF (γ＝1.0), ON (γ=0.45); selectable (option)
Remote control
With Camera Link connector input or 12pin Circular connector
input, the camera can be remote controlled.
When the camera is remote controlled via 12 pin circular
connector, neither HD nor VD is valid.

VCC-F32U29CL Rev. 900-513-31-01
©2007 CIS Corporation. All rights reserved.
9
5.3. Camera Link Connector Bit Assignment (Base Configuration)
RGB Data output: 8 bit output (No.8 SW on the rear panel: On)
Port/bit 24 bit RGB Port/bit 24 bit RGB Port/bit 24 bit RGB
Port A0 R0 Port B0 G0 Port C0 B0
Port A1 R1 Port B1 G1 Port C1 B1
Port A2 R2 Port B2 G2 Port C2 B2
Port A3 R3 Port B3 G3 Port C3 B3
Port A4 R4 Port B4 G4 Port C4 B4
Port A5 R5 Port B5 G5 Port C5 B5
Port A6 R6 Port B6 G6 Port C6 B6
Port A7 R7 Port B7 G7 Port C7 B7
RAW Data output: 8 bit output (No.8 & No.9 SW on the rear panel: Off)
Port/bit 8bit×3 Port/bit 8bit×3 Port/bit 8bit×3
Port A0 D0 Port B0 D0 Port C0 D0
Port A1 D1 Port B1 D1 Port C1 D1
Port A2 D2 Port B2 D2 Port C2 D2
Port A3 D3 Port B3 D3 Port C3 D3
Port A4 D4 Port B4 D4 Port C4 D4
Port A5 D5 Port B5 D5 Port C5 D5
Port A6 D6 Port B6 D6 Port C6 D6
Port A7 D7 Port B7 D7 Port C7 D7
※ The same signals are output through 3 taps. (8bit x 3, Port A=B=C)
10 bit output mode（No. 8 SW off & No.9 SW on）
Port/bit 8bit×3 Port/bit 8bit×3 Port/bit 8bit×3
Port A0 D0 Port B0 D8 Port C0 D0
Port A1 D1 Port B1 D9 Port C1 D1
Port A2 D2 Port B2 nc Port C2 D2
Port A3 D3 Port B3 Nc Port C3 D3
Port A4 D4 Port B4 D8 Port C4 D4
Port A5 D5 Port B5 D9 Port C5 D5
Port A6 D6 Port B6 nc Port C6 D6
Port A7 D7 Port B7 nc Port C7 D7
※ The same signals are output through 2 taps (10bit x 2).

VCC-F32U29CL Rev. 900-513-31-01
©2007 CIS Corporation. All rights reserved.
10
5.4. Function Settings
Camera functions can be set with serial data communication.
Function Address Data Remarks
LOC/REM 000
0: Local (Camera SW) Control 1: Remote Control F, G
Gain 001
0: 0dB
1: 0dB
2: +6dB
3: +12dB
4: Manual Gain (Refer to address 008)
F, G
E-Shutter
Position 002
0～7: (For the details, refer to 7.1.1. Shutter setting.）
8～15: -
16: Manual Shutter （Refer to address 009 & 010）
F, G
White
Balance 003
0: 2600°K
1: 3200°K
2: 5600°K
3: 9000°K
4: Manual White Balance (Refer to address 006 & 007)
F
Trigger
Mode 004
0: Standard Mode
1: Standard Trigger Mode
2: Pulse Width Trigger Mode
3: Standard Trigger Mode (Slow Shutter)
F, G
Initial setting
(0)
SCAN
Mode 005
0：Standard Scan Mode
1：Partial Scan Mode
F, G
Initial setting
(0)
Manual R
Gain 006 R Gain 64～255 ※Valid when address 003 data is 4 (manual). F
Manual B
Gain 007 B Gain 64～255 ※Valid when address 003 data is 4 (manual) F
Manual Gain 008 0～255: +0dB～+12dB ※Valid when address 001 data is 4
(manual)
F, G
Manual
Shutter
009 &
010
・Standard Scan Mode (Address 005:0) F, G
0～max 1251 (max address 009:4 address 010:227)
Shutter Speed = 1 /(1251-DATA)*26.67us+13.33us）
・Partial Scan Mode (address 005:1)
0～max (address 052 & 053-1)
Shutter Speed
=1 /((address 052 & 053-1) - DATA) *26.67us+13.33us
Address 009 MSB and address 010 LSB make 10 bits in total.