Cisco TelePresence Profile 55 Dual Assembly instructions

PRECAUTIONS
Please follow the steps in this installation guide when
unpacking and assembling Profile 55” Dual.
UNPACKING THE SYSTEM AT THE DESTINATION
It is highly recommend to start the unpacking and assembling
of Profile 55” Dual at the place where it is to be used.
NOTE: If it is not possible to bring the complete delivery to
the room where Profile 55” Dual is to be used, then unpack
and bring the smaller units to the destination.
• The monitor box requires two (2) persons to lift (55 kg /
121 lb).
• The bottom module column requires two (2) persons to lift
(40kg / 88lb).
• The foot module requires two (2) persons to lift
(stand-alone: 35kg / 77lb; wall mount: 20kg / 44lb).
MANPOWER
A minimum of two (2) persons are required when installing
Profile55” Dual.
INSTALLATION NEAR A SOCKETOUTLET
The equipment must be installed near a socket-outlet. The
socket-outlet shall be easily accessible after installation.
ROOM GUIDELINES
NOTE: The floor must be in level.
The recommended distance between the Profile 55” Dual
and the meeting room table should be minimum 1.5 m / 59 in.
Read more about room guidelines in the Video conferencing
room primer.
USER DOCUMENTATION
The user documentation for this product, including
compliance and safety information, is available on the Cisco
web site.
Go to: http://www.cisco.com/go/telepresence/docs.
DIMENSIONS OF THE PROFILE 55” DUAL
• Height: 64.6” / 164 cm
• Width: 99.2” / 252 cm
• Depth (wall mount): 10.2” / 26cm
• Depth (stand-alone): 17.7” / 45cm
• Weight: 440lb / 200 kg
LEVELLING ADJUSTMENT
Make sure the unit is stable.
Place the level adjustment tool on the
foot wheel under the foot module for
height adjustment.
Seen from above, turn clockwise to
adjust the height up. Use the opposite
side of the tool and turn counterclockwise
to adjust down.
Installing Cisco TelePresence System Profile 55” Dual
Page 178-20440-01 Profile 55 Dual Installation Sheet | 2011 OCTOBER | © 2011 Cisco Systems, Inc. All rights reserved.
THE PROFILE 55” DUAL DELIVERY CONTAINS:
Monitor box:
• Two monitors and
speaker grilles
Bottom module column
Camera
Touch 8” interface device
Foot module box:
• Foot module (stand-alone or wall
mount)
• Six M8×45 screws
• Two wall mount brackets and four
M6×10 screws (for wall mount only)
• Level adjustment tool
Monitor back cover box:
• Monitor back cover
• Two M4×15 screws for the back
cover
• Monitor brackets
• M4×25 and M4×8 screws for the
monitor brackets
• Four M8×15 screws to fasten the
monitors to the column
Accessories box:
• Cables
• Microphones, 4 pcs
• Remote control and 4 AAA
batteries
• Gloves, 2 pairs
• Cleaning cloth
• Allen key, screwdriver
1Content overview
Remove the outer cover and locate the different boxes as illustrated below.
2Lifting the column out of the package. Mounting the column to the foot module to complete the bottom module
Left monitor
Right monitor
Column
Stand-alone
foot module
3WHEN YOU HAVE A WALL MOUNT FOOT MODULE: Mounting the column to the foot module and fastening it to the wall CAUTION
Due to the size and weight of this equipment, it is very
important that the wall mount unit is safely installed
according to the installation instructions and that the
wall is able to safely support the product. It is highly
recommended that the wall mounted system is installed
by trained personnel.
Mount the column to the wall mount foot module, similar to step 2.
1. Fasten the wall brackets to the bottom module with the four M6×10
screws. Use the Allen key.
2. Place the bottom module by the wall, mark where to fasten the
bracket and move the bottom module away.
3. Add the suitable fixing device for the screws in the wall, and fasten
the bottom module.
1. Move the foot module to its
permanent location, and place the
column on the foot module.
2. Open the rear door. Unscrew the two
thumb nuts and remove the door stop
bracket.
3. Carefully open the rear door
completely.
4. Fasten the column to the foot module
with three M8×45 screws on each
side as illustrated to the right.
5. Fasten the door stop bracket again
with the two thumb nuts.
CAUTION
HE AVY
Rev. Date Prep. Checked Change
-
-
-
Telecom AS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Part weight:
Sheet size:
Scale:
Surface treatment
Specification:
Material
Tolerances
Unit:
European
projection
Sheet 1 of 1
All materials, finishes, and proccesses
must comply with the RoHS directives
Dimensions without paint or finish
Flame class requirement: -
Processes
Type:
Manufacturer:
Type number:
Thickness:
Color:
Surface:
Glossiness:
Flame class:
UL reference:
3D CAD model file 120601 rev. 03 is master
Packaging Kit Profile 52" Dual
120601 rev.
71743g
A3
mm
1:8
Monitor back cover and monitor brackets
Right and left monitor
Bottom module column
Camera
Foot module
Accessories box
Touch controller
Add the suitable fixing device for the screws in the wall.
The wall
CAUTION
HE AVY
The monitors come in a separate box. The monitor box contains monitors and
speaker grilles for the monitors. Remove the lid and locate the left and right
monitors and the speaker grilles.
CAUTION
HE AVY
Front
Rev. Date Prep. Checked Change
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Part weight:
Sheet size:
Scale:
Surface treatment
Specification:
Material
Tolerances
Unit:
European
projection
Sheet 1 of 1
All materials, finishes, and proccesses
must comply with the RoHS directives
Dimensions without paint or finish
Flame class requirement: -
Processes
Type:
Manufacturer:
Type number:
Thickness:
Color:
Surface:
Glossiness:
Flame class:
UL reference:
3D CAD model file 117325 rev. 00D is master
TANDBERG Aquarius dual 52"
117325 rev.
38276168g
A3
mm
1:7
-
-
-
-
-
-
-
-
-
-
Grab here when
lifting the column.
CAUTION
HE AVY
Front
Rear side
Door stop bracket
Rear side
Screws to
fasten the
column
Screws to
fasten the
column
Access the innermost screws through these holes.
The bottom module is viewed from the rear side.
Allen key and
six M8×45
screws
Allen key and four
M6×10 screws
Screws to fasten the wall
bracket to the bottom module

Installing Cisco TelePresence System Profile 55” Dual
Page 278-20440-01 Profile 55 Dual Installation Sheet | 2011 OCTOBER | © 2011 Cisco Systems, Inc. All rights reserved.
6Mounting the camera cables and the camera
1. Locate the camera cables in the bottom module (the two long
cables).
2. Locate the hole in the monitor where the cables can be
pushed through. Push the cables through the hole in the right
monitor.
3. On the rear side, place the cables in the foam rails that are
going on the rear side of the monitor.
CAMERA CABLE CONFIGURATION
PrecisionHD 1080p
HDMI
RJ45
For countries with 60Hz current frequency
you must set the PrecisionHD 1080p camera
DIPswitch to: 00100.
4. Connect the RJ45 and HDMI cables to the camera, see
illustration.
5. Place the camera and slide it towards the front.
6. Place the camera cables in the foam rails.
Upper monitor
bracket
Lower monitor
bracket*
* The lower monitor bracket is not used on a wall
mounted system. Instead, make sure the monitors
are aligned at the front.
8Connecting the system
Ethernet cable
PC cable
Microphone cable
Power cable
1. Open the rear door and lead the cables
out through the openings at the lower
part of the door.
2. Close the rear door carefully. Take care
not to shut the cables in the door.
3. Place the PC cable and the
microphones on the table.
4. Connect the Ethernet cable.
5. Connect the power cable (use the
provided country specific cable).
6. Open the front door and turn on the
monitor.
7. Follow the instructions in the
accompanying Touch 8” installation
guide to connect and initialize the touch
interface device.
8. The system should be up and running
in a few minutes.
The rear door
Open the front door and locate the monitor connectors and cables. Connect the cables
as illustrated below.
Connect the left monitor:
1. HDMI cable
2. Speaker in, 15 pin D-SUB cable
(tighten the screws)
3. Power cable
Connect the right monitor:
1. HDMI cable
2. Speaker in, 15 pin D-SUB cable
(tighten the screws)
3. Power cable
4Unpacking the monitor box and lifting out the monitors; fastening the monitors to the bottom module
LIFTING HANDLES. Locate the
orange lifting handles in the front
and rear side of the monitor.
1. Carefully lift the right monitor out of
the packaging as illustrated.
2. See the two triangle holes in the
monitor base. Use these holes to
help guiding the monitor to enter the
poles on the column.
3. Repeat the above procedure for the
left monitor.
Right monitor
Left monitor
Triangular holes to
guide the monitor
Allen key
4 * M8×15
Unpack the
monitor box.
Lift out to open
the snap lockers.
CAUTION
HE AVY
7Mounting the back cover and top lid, and finishing up
1. Hook on the back cover in the
slots at the top and snap it in place
with the lower magnets.
The magnets are strong. Make
sure your fingers are not trapped.
2. Fasten the back cover with two
M4×15 bolts and nuts (tool: Allen
key).
3. Slide the top lid into position and
snap it tight with the magnets.
4. Remove the plastic foils
from the screen and the
monitor frame.
5. Snap on the two speaker
grilles.
6. Use the supplied cloth to
clean the system.
4. Align the monitors at the top and fasten the two monitors
together using the upper monitor bracket and the M4×25
screws.
5. Fasten the two monitors together at the bottom using the
lower monitor bracket and the M4×8 screws.
6. Fasten the monitor to the column poles using
four M8×15 screws, two screws at each monitor.
7. Tighten the monitor gently to the bottom module until the
monitor cannot be moved anymore.
Back cover
Top lid
5Connecting the monitor cables to both monitors
Left monitor connectors
Power HDMI 1 Speaker in
Right monitor connectors
PowerHDMI 1 Speaker in
EMC A Class declaration
WARNING: This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
A级声明 (A Class product declaration)
本产品为 A级ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明
(We declare here that the subject product is A class ITE product, and the
following statement is clearly marked in the user manual or nameplate):
声明所在位置 (Position of the Declaration): 使用说明 User Manual
铭牌 Nameplate
申请号 (Application No.)：
申请人 (Applicant):
型号 (Model Number)：
签字/盖章 Signature/Stamp:
日期 Date:
警告
此为 A级产品。在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对干扰采取切实可行的措施。
WARNING:
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.