Cisco C9200L-24PXG-2Y-A User manual

Cisco Catalyst 9200 Series Switches Hardware Installation Guide
First Published: 2018-11-19
Last Modified: 2020-11-17
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Cisco Catalyst
C9200-L C9200L-24PXG-2Y-A o cerca il tuo prodotto tra le migliori offerte di Switch

©2018–2020 Cisco Systems, Inc. All rights reserved.

CONTENTS
Product Overview 1
CHAPTER 1
Switch Models 1
Front Panel Components 3
10/100/1000 Ports 4
PoE and PoE+ Ports 4
Multigigabit Ethernet Ports 5
Management Ports 5
USB Type A Port 6
Uplink Ports 6
Rear Panel 8
RFID Tag 9
StackWise Ports 9
Power Supply Modules 9
Fan Modules 12
Ethernet Management Port 12
RJ-45 Console Port 13
Network Configurations 13
Installing the Switch 15
CHAPTER 2
Preparing for Installation 15
Safety Warnings 15
Installation Guidelines 17
Shipping Box Contents 17
Tools and Equipment 18
Verifying Switch Operation 18
Planning a Switch Data Stack 19
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
iii

Switch Stacking Guidelines 19
Data Stack Cabling Configurations 20
Data Stack Bandwidth and Partitioning Examples 21
Power-On Sequence for Switch Stacks 23
Mounting the Switch 24
Rack-Mounting 24
Attaching the Rack-Mount Brackets 25
Mounting the Switch in a Rack 27
Installing the Switch on a Table or Shelf 27
After Switch Installation 28
Connecting to the StackWise Ports 29
Connecting Devices to the Ethernet Ports 31
10/100/1000/Multigigabit Ethernet Port Connections 31
Auto-MDIX Connections 31
PoE and POE+ Port Connections 31
Installing a Network Module 33
CHAPTER 3
Installing a Network Module in the Switch 33
Safety Warnings 33
Installing a Network Module 34
Removing a Network Module 35
Finding the Network Module Serial Number 36
Installing and Removing Pluggable Transceiver Modules 37
Installing a Cisco Pluggable Transceiver Module 37
Removing a Cisco Pluggable Transceiver Module 39
Installing a Power Supply Unit 41
CHAPTER 4
Power Supply Modules Overview 41
Finding the Power Supply Module Serial Number 44
Installation Guidelines 45
Installing or Replacing an AC Power Supply Module 46
Installing a Fan Module 49
CHAPTER 5
Fan Modules Overview 49
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
iv
Contents

Installation Guidelines 50
Installing a Fan Module 50
Finding the Fan Module Serial Number 51
Configuring the Switch 53
CHAPTER 6
Configuring the Switch Using the Web User Interface 53
Configuring the Switch Using the CLI 53
Accessing the CLI Through the Console Port 53
Connecting the RJ-45 Console Port 53
Connecting the USB Console Port 54
Installing the Cisco Microsoft Windows USB Device Driver 55
Installing the Cisco Microsoft Windows 7 USB Driver 55
Uninstalling the Cisco Microsoft Windows USB Driver 55
Uninstalling the Cisco Microsoft Windows 7 USB Driver 55
Technical Specifications 57
APPENDIX A
Environmental and Physical Specifications 57
Specifications for the Power Supplies and Fans 61
Switch LEDs 63
APPENDIX B
LEDs 63
Console LED 63
System LED 64
ACTIVE LED 64
STACK LED 65
PoE LED 66
Port LEDs and Modes 66
Beacon LED 68
RJ-45 Console Port LED 69
Fan LED 69
Uplink Port LEDs 69
Introduction ?
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
v
Contents

Cisco Catalyst 9200 Series Switches Hardware Installation Guide
vi
Contents

CHAPTER 1
Product Overview
•Switch Models, on page 1
•Front Panel Components, on page 3
•Rear Panel, on page 8
•Network Configurations, on page 13
Switch Models
The Cisco Catalyst 9200 Series switches have four modular (C9200) and eight fixed (C9200L) switch models.
The following tables describe all the available Cisco Catalyst 9200 Series switches and the features supported.
Table 1: C9200L Switch Models and Descriptions
DescriptionSwitch Model
Stackable 24x1G PoE+ ports; 4x1G SFP fixed uplink ports; 2 power
supply slots; 2 fixed fans; supports StackWise-80.
C9200L-24P-4G
Stackable 24x1G PoE+ ports; 4x10G SFP+ fixed uplink ports; 2
power supply slots; 2 fixed fans; supports StackWise-80.
C9200L-24P-4X
Stackable 24x1G ports; 4x1G SFP fixed uplink ports; 2 power supply
slots; 2 fixed fans; supports StackWise-80.
C9200L-24T-4G
Stackable 24x1G ports; 4x10G SFP+ fixed uplink ports; 2 power
supply slots; 2 fixed fans; supports StackWise-80.
C9200L-24T-4X
Stackable 48x1G PoE+ ports; 4x1G SFP fixed uplink ports; 2 power
supply slots; 2 fixed fans; supports StackWise-80.
C9200L-48P-4G
Stackable 48x1G PoE+ ports; 4x10G SFP+ fixed uplink ports; 2
power supply slots; 2 fixed fans; supports StackWise-80.
C9200L-48P-4X
Stackable 48x1G ports; 4x1G SFP fixed uplink ports; 2 power supply
slots; 2 fixed fans; supports StackWise-80.
C9200L-48T-4G
Stackable 48x1G ports; 4x10G SFP+ fixed uplink ports; 2 power
supply slots; 2 fixed fans; supports StackWise-80.
C9200L-48T-4X
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
1

DescriptionSwitch Model
Stackable 8xMultigigabit Ethernet PoE+ ports and 16x1G PoE+
ports; 4x10G SFP+ fixed uplink ports; 2 power supply slots; 2 fixed
fans; supports StackWise-80.
C9200L-24PXG-4X
Stackable 8xMultigigabit Ethernet PoE+ ports and 16x1G PoE+
ports; 2x25G SFP28 fixed uplink ports; 2 power supply slots; 2 fixed
fans; supports StackWise-80.
C9200L-24PXG-2Y
Stackable 12xMultigigabit Ethernet PoE+ ports and 36x1G PoE+
ports; 4x10G SFP+ fixed uplink ports; 2 power supply slots; 2 fixed
fans; supports StackWise-80.
C9200L-48PXG-4X
Stackable 8xMultigigabit Ethernet PoE+ ports and 40x1G PoE+
ports; 2x25G SFP28 fixed uplink ports; 2 power supply slots; 2 fixed
fans; supports StackWise-80.
C9200L-48PXG-2Y
Stackable 48x1G PoE+ ports with partial PoE support; 4x1G SFP
fixed uplink ports; 2 power supply slots; 2 fixed fans; supports
StackWise-80.
C9200L-48PL-4G
Stackable 48x1G PoE+ ports with partial PoE support; 4x10G SFP
fixed uplink ports; 2 power supply slots; 2 fixed fans; supports
StackWise-80.
C9200L-48PL-4X
Table 2: C9200 Switch Models and Descriptions
DescriptionSwitch Model
Stackable 24x1G PoE+ ports; 4x1G and 4x10G network modules
for uplink ports; 2 power supply slots; 2 field-replaceable fans;
supports StackWise-160.
C9200-24P
Stackable 24x1G PoE+ ports; 4x1G and 4x10G network modules
for uplink ports; 2 power supply slots; 2 field-replaceable fans;
supports StackWise-160.
C9200-24PB
Stackable 24x1G ports; 4x1G and 4x10G network modules for uplink
ports; 2 power supply slots; 2 field-replaceable fans; supports
StackWise-160.
C9200-24T
Stackable 48x1G PoE+ ports; 4x1G and 4x10G network modules
for uplink ports; 2 power supply slots; 2 field-replaceable fans;
supports StackWise-160.
C9200-48P
Stackable 48x1G PoE+ ports; 4x1G and 4x10G network modules
for uplink ports; 2 power supply slots; 2 field-replaceable fans;
supports StackWise-160.
C9200-48PB
Stackable 48x1G ports; 4x1G and 4x10G network modules for uplink
ports; 2 power supply slots; 2 field-replaceable fans; supports
StackWise-160.
C9200-48T
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
2
Product Overview
Switch Models

DescriptionSwitch Model
Stackable 8 Multigigabit Ethernet and 16x1G PoE+ ports; supports
4x10G, 2x25G and 2x40G network modules for uplink ports; 2 power
supply slots; 2 field-replaceable fans; supports StackWise-160.
C9200-24PXG
Stackable 8 Multigigabit Ethernet and 40x1G PoE+ ports; supports
4x10G, 2x25G and 2x40G network modules for uplink ports; 2 power
supply slots; 2 field-replaceable fans; supports StackWise-160.
C9200-48PXG
Stackable 48x1G PoE+ ports with partial PoE support; 4x1G and
4x10G network modules for uplink ports; 2 power supply slots; 2
field-replaceable fans; supports StackWise-160.
C9200-48PL
Front Panel Components
This section describes the front panel components of Cisco Catalyst 9200 Series switches :
• 24 or 48 downlink ports of one of the following types:
• 10/100/1000
• 10/100/1000 PoE+
• 1G/10G Uplink ports
• USB Type A storage ports
• USB mini-Type B console port
• LEDs
• Blue Beacon
All the switch models have similar components. See the following illustration for example.
The Cisco Catalyst 9200 Series switches might have slight cosmetic differences on the bezels.
Note
Figure 1: Front Panel of a C9200L Switch
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
3
Product Overview
Front Panel Components

USB Type A storage ports5Blue Beacon (UID button)1
10/100/1000 PoE+ ports6Mode button2
Fixed uplink ports7Status LEDs3
USB mini-Type B (console) port4
Figure 2: Front Panel of a C9200 Switch
USB Type A storage ports4Blue Beacon (UID button)1
10/100/1000 PoE+ ports5Mode button2
Network Module with uplink
ports
6USB mini-Type B (console)
port
3
10/100/1000 Ports
The 10/100/1000 ports use RJ-45 connectors with Ethernet pinouts. The maximum cable length is 328 feet
(100 meters). The 100BASE-TX and 1000BASE-T traffic requires twisted pair (UTP) cable of Category 5
or higher. The 10BASE-T traffic can use Category 3 cable or higher.
PoE and PoE+ Ports
The PoE and PoE+ ports provide the following functionality:
• PoE/PoE+ ports: Support for IEEE 802.3af-compliant powered devices (up to 15.4W PoE per port) and
support for IEEE 802.3at-compliant powered devices (up to 30W PoE+ per port).
• Support for pre-standard Cisco powered devices.
• Configurable support for Cisco intelligent power management, including enhanced power negotiation,
power reservation, and per-port power policing.
See the Power Supply Modules, on page 9 for the power supply matrix that defines the available PoE and
PoE+ power per port. The output of the PoE+ circuit has been evaluated as a Limited Power Source (LPS)
per IEC 60950-1.
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
4
Product Overview
10/100/1000 Ports

Multigigabit Ethernet Ports
The Multigigabit (mGig) Ethernet ports can be configured to auto-negotiate multiple speeds on switch ports.
The ports support 100 Mbps, 1 Gbps, 2.5 Gbps, and 5 Gbps speeds on Category 5e (Cat5e) cables, and up to
10 Gbps over Category 6 (Cat6) and Category 6A (Cat6A) cables up to a maximum of 100 m. 10Gbps over
Cat6 cable is limited for distances up to 55 m. For 10GBASE-T, Cat6a can support up to 100 m when
transmitting 10Gbps. Due to the extra bandwidth requirements from the cable, additional limitations exist for
best performance. These limitations include, but are not limited to cable reach, cable bundling parameters
(tightness, frequency, number of cables, speed with respect to each cable) and cable termination quality.
The 802.3 channel requirements for interoperability typically limit the cable reach to 100 m, but other factors
can shorten this reach. In addition, for both UPOE and HPOE and data integrity, the 100 m total should not
include more than 10 m total stranded or patch cable. Therefore, it is assumed that a 100 m link includes a
maximum of two 5 m patch cables of the appropriate category, and 90 m of plenum or riser (i.e. solid copper
core) cables. Ensure that you follow the TIA guidance on cable dressing.
It is recommended to test the complete link using an appropriate cable tester for 10 Gbps as well as 5 Gbps
links. However, even if the link passes cable testing, it is still prone to occasional errors due to aggressors in
the bundle, and physical disturbances of the cables. As an example of bundling limitations, for 5 Gbps with
cat5e cable, only a total 45 m bundled length is supported; the remaining 55 m should be unbundled. For
bundling, follow Cisco Guidelines and Best Practices for the Installation and Maintenance of Data Networking
Equipment which recommends the use of Velcro ties every 1 to 2 m for bundled sections.
If you are upgrading the network gear but reusing the existing cable plant, note that at speeds above 2.5 Gbps
traditional Cat5e channel specifications do not support full 100 m reach. To ensure 5 Gbps link speeds, we
recommend using Cat6a cabling. For more information, see the Whitepaper from NBASE-T alliance, which
has now merged with Ethernet Alliance, archived at
https://archive.nbaset.ethernetalliance.org/library/white-paper-2/.
Multigigabit ports do not support half duplex mode. Use full duplex mode.
Note
Management Ports
The management ports connect the switch to a PC running Microsoft Windows or to a terminal server.
• Ethernet management port. See Ethernet Management Port, on page 12.
• RJ-45 console port (EIA/TIA-232). See RJ-45 Console Port, on page 13.
• USB mini-Type B console port (5-pin connector).
The 10/100/1000 Ethernet management port connection uses a standard RJ-45 crossover or straight-through
cable. The RJ-45 console port connection uses the supplied RJ-45-to-DB-9 female cable. The USB console
port connection uses a USB Type A to 5-pin mini-Type B cable. The USB console interface speeds are the
same as the RJ-45 console interface speeds.
If you use the USB mini-Type B console port, the Cisco Windows USB device driver must be installed on
any PC connected to the console port (for operation with Microsoft Windows). Mac OS X or Linux do not
require special drivers.
The 4-pin mini-Type B connector resembles the 5-pin mini-Type B connectors. They are not compatible. Use
only the 5-pin mini-Type B.
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
5
Product Overview
Multigigabit Ethernet Ports

Figure 3: USB Mini-Type B Port
This illustration shows a 5-pin mini-Type B USB port.
With the Cisco Windows USB device driver, you can connect and disconnect the USB cable from the console
port without affecting Windows HyperTerminal operations.
The console output always goes to both the RJ-45 and the USB console connectors, but the console input is
active on only one of the console connectors at any one time. The USB console takes precedence over the
RJ-45 console. When a cable is connected into the USB console port, the RJ-45 console port becomes inactive.
Conversely, when the USB cable is disconnected from the USB console port, the RJ-45 port becomes active.
You can use the command-line interface (CLI) to configure an inactivity timeout which reactivates the RJ-45
console if the USB console has been activated and no input activity has occurred on the USB console for a
specified time.
After the USB console deactivates due to inactivity, you cannot use the CLI to reactivate it. Disconnect and
reconnect the USB cable to reactivate the USB console. For information on using the CLI to configure the
USB console interface, see the Software Configuration Guide.
USB Type A Port
The USB Type A port provides access to external USB flash devices (also known as thumb drives or USB
keys).
The port supports Cisco USB flash drives with capacities from 128 MB to 8 GB. USB devices with port
densities of 128 MB, 256 MB, 1 GB, 4 GB, and 8 GB are supported. When combined with stacking, you can
upgrade other switches in the stack from an USB key inserted in any switch within the stack. Cisco IOS
software provides standard file system access to the flash device: read, write, erase, and copy, as well as the
ability to format the flash device with a FAT file system.
It provides you with the ability to automatically upgrade the internal flash with the USB drive's configuration
and image for emergency switch recovery using USB auto-upgrade. This feature checks the internal flash for
a bootable image and configuration and if either image or the configuration is not available, then the USB
drive is checked for boot images and configuration. If the boot image and configuration are available, these
are copied to flash for the reboot.
Uplink Ports
The Cisco Catalyst 9200 Series switches support both fixed uplinks and modular uplinks. The C9200 switch
models support modular uplinks with one hot-swappable network module that provides uplink ports to connect
to other devices.
The fixed uplink ports on C9200L switch models support the following types of transceiver modules.
• 4x1G ports that support 1G SFP modules.
• 4x10G ports that support either 1G SFP or 10G SFP+ modules.
• 2x25G ports that support SFP28 modules.
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
6
Product Overview
USB Type A Port

For supported Cisco pluggable transceiver modules (SFP, SFP, SFP28 and QSFP+ modules), refer to the
Cisco Transceiver Modules Compatibility Information at
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html
For information about installing an (uplink) transceiver module, see Installing a Cisco Pluggable Transceiver
Module, on page 37.
Note
Figure 4: Network Module C9200-NM-4G
LEDs2Module slot1
The following table lists the optional Cisco Catalyst 9200 Series Switches uplink network modules with 4x1G,
4x10G, 2x25G, and 2x40G slots.
Table 3: Supported Network Modules
DescriptionNetwork Module
This module has four 1G SFP module slots. Any combination of standard
SFP modules is supported. SFP+ modules are not supported.
If you insert an SFP+ module in the 1G network module, the SFP+ module
does not operate, and the switch logs an error message. This module is not
supported on C9200 Multigigabit Ethernet switches.
C9200-NM-4G
This module has four 10G SFP module slots. Each port supports a 1G or 10G
connection. Any combination of standard SFP modules is supported.
This module is supported on both 1G and Multigigabit Ethernet switch models
of C9200 switches.
C9200-NM-4X
This module has two 25 Gigabit Ethernet SFP28 module slots. Any
combination of SFP, SFP+, and SFP28 modules are supported.
This module is supported only on C9200 Multigigabit Ethernet switches.
C9200-NM-2Y
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
7
Product Overview
Uplink Ports

DescriptionNetwork Module
This module has two 40G slots with a QSFP+ connector in each slot.
This module is supported only on C9200 Multigigabit Ethernet switches.
C9200-NM-2Q
Insert this blank module when the switch has no uplink ports to enable
sufficient airflow.
C9200-NM-BLANK
For information about installing a network module, see Installing a Network Module, on page 34.
Note
Rear Panel
The switch rear panel includes StackWise connectors, fan modules, and power supply modules.
Figure 5: Rear Panel of a C9200L Switch
Blue Beacon LED4RJ-45 console port1
MGMT (RJ-45
10/100/1000 management
port)
5Fixed fan modules on
C9200L switches
2
StackWise-80 port
connectors
6Power supply module
slots
3
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
8
Product Overview
Rear Panel

Figure 6: Rear Panel of a C9200 Switch
Blue Beacon LED4RJ-45 console port1
MGMT (RJ-45
10/100/1000 management
port)
5Modular fan modules on
C9200 switches
2
StackWise-160 port
connector slots with stack
blanks installed
6Power supply module
slots
3
RFID Tag
The switch has a built-in, front-facing, passive RFID tag that uses UHF RFID technology and requires an
RFID reader with compatible software. It provides auto-identification capabilities for asset management and
tracking. The RFID tags are compatible with the Generation 2 GS1 EPC Global Standard and are ISO 18000-6C
compliant. They operate in the 860- to 960-MHz UHF band. For more information, see Radio Frequency
Identification (RFID) on Cisco Catalyst 9000 Family Switches White Paper.
StackWise Ports
StackWise ports are used to connect switches in StackWise stacking configurations. The switch ships with a
0.5-meter StackWise cable that you can use to connect the StackWise ports. For more information on StackWise
cables, see Connecting to the StackWise Ports, on page 29.
Use only approved cables, and connect only to similar Cisco equipment. Equipment might be damaged if
connected to nonapproved Cisco cables or equipment.
Caution
Power Supply Modules
The switch has a field replaceable main AC power supply module and a redundant hot-swappable field
replaceable AC power supply module. The switch is powered through one or two internal power supply
modules. In switches with PoE capability, the redundant power supply can also be used for extra PoE power.
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
9
Product Overview
RFID Tag

Following are the power supply modules supported on Cisco Catalyst 9200 Series Switches:
• PWR-C5-125WAC
• PWR-C5-600WAC
• PWR-C5-1KWAC
• PWR-C6-125WAC
• PWR-C6-600WAC
• PWR-C6-1KWAC
The switch has two internal power supply module slots. You can use two AC power supply modules or one
power supply module and a blank module (PWR-C5-BLANK).
The switch can operate with either one or two active power supply modules.
Switch Models, on page 1 shows the default power supply modules that ship with each switch model. All
power supply modules (except the blank modules) have internal fans. All switches ship with a blank power
supply module in the second power supply slot. Each AC power supply module has a power cord
(CAB-TA-XXX) for connection to an AC power outlet.
Do not operate the switch with one power supply module slot empty. For proper chassis cooling, both power
supply module slots must be populated with either a power supply or a blank module.
Caution
The power supply modules are autoranging units that support input voltages between 100 and 240 VAC. The
output voltage range is 12 to 12.5 V for 125W power supply and 54 to 56 V for 600W and 1000W power
supplies.
All the PoE-enabled switches when installed with both the power supplies support full PoE+; 1440W on a
48-port switch and 740W on a 24-port switch.
The partial PoE-enabled switches support only 600W power supply providing a PoE budget of 370W. If the
switch is installed with one power supply, the available POE budget is 370W and 740W, if there are two
power supplies installed.
The following tables show the PoE available and PoE requirements for PoE switch models.
Table 4: Available PoE with AC Power Supply
Full PoE with Redundant
Power Supply
Available PoEDefault Power SupplyModels
C9200 Switches
740W370WPWR-C5-600WAC or
PWR-C6-600WAC
C9200-24P
1440W740WPWR-C5-1KWAC or
PWR-C6-1KWAC
C9200-48P
--PWR-C5-125WAC or
PWR-C6-125WAC
C9200-24T
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
10
Product Overview
Power Supply Modules

Full PoE with Redundant
Power Supply
Available PoEDefault Power SupplyModels
--PWR-C5-125WAC or
PWR-C6-125WAC
C9200-48T
740W370WPWR-C5-600WAC or
PWR-C6-600WAC
C9200-24PB
1440W740WPWR-C5-1KWAC or
PWR-C6-1KWAC
C9200-48PB
740W370WPWR-C5-600WAC or
PWR-C6-600WAC
C9200-48PL
740W370WPWR-C5-600WAC or
PWR-C6-600WAC
C9200-24PXG
1440W740WPWR-C5-1KWAC or
PWR-C6-1KWAC
C9200-48PXG
C9200L Switches
740W370WPWR-C5-600WAC
C9200L-24P-4G
740W370WPWR-C5-600WACC9200L-24P-4X
740W370WPWR-C5-600WACC9200L-24PXG-2Y
740W370WPWR-C5-600WACC9200L-24PXG-4X
——PWR-C5-125WACC9200L-24T-4G
——PWR-C5-125WACC9200L-24T-4X
1440W740WPWR-C5-1KWACC9200L-48P-4G
1440W740WPWR-C5-1KWACC9200L-48P-4X
740W370WPWR-C5-600WACC9200L-48PL-4G
740W370WPWR-C5-600WACC9200L-48PL-4X
1440W740WPWR-C5-1KWACC9200L-48PXG-2Y
1440W740WPWR-C5-1KWACC9200L-48PXG-4X
——PWR-C5-125WACC9200L-48T-4G
——PWR-C5-125WACC9200L-48T-4X
The power supply modules have two status LEDs.
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
11
Product Overview
Power Supply Modules

Table 5: Switch Power Supply Module LEDs
DescriptionPS OKDescriptionAC OK
Output is disabled, or input is outside
operating range (AC LED is off).
OffNo AC input power.Off
Power output to switch active.GreenAC input power present.Green
Output has failed.Red
Fan Modules
The Cisco Catalyst 9200 Series Switches supports two internal fixed 12-V fan modules and two field-replaceable
fan modules (C9200-FAN=). The C9200 models support modular fans whereas the C9200L models provide
two internal fixed fans.
For information about the type of fan module supported on different switch models, see Switch Models, on
page 1.
The air circulation system consists of the fan modules and the power supply modules. The airflow patterns
vary depending on the power supply configuration. The switch can operate at ambient temperature if one of
the fans fail.
Figure 7: Switch Airflow Pattern
The following illustration shows the airflow pattern for the switches. The blue arrow shows cool airflow, and
the red arrow shows warm airflow.
Ethernet Management Port
You can connect the switch to a host such as a Windows workstation or a terminal server through the
10/100/1000 Ethernet management port or one of the console ports. The 10/100/1000 Ethernet out-of-band
management port is a virtual routing and forwarding (VRF) interface and uses a RJ-45 crossover or
straight-through cable.
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
12
Product Overview
Fan Modules

The 10/100/1000 Ethernet management port is an RJ-45 connector that should be connected to a Windows
workstation or a terminal server. Do not connect this port to another port in the same switch or to any port
within the same switch stack.
Note
The following table shows the Ethernet management port LED colors and their meanings.
Table 6: Ethernet Management Port LED
DescriptionColor
Link up but no activity.Green
Link up and activity.Blinking green
Link down.Off
RJ-45 Console Port
The RJ-45 console port connection uses the supplied RJ-45-to-DB-9 female cable.
The following table shows the RJ-45 console port LED colors and their meanings.
Table 7: RJ-45 Console LED
DescriptionColor
RJ-45 console port is active.Green
The port is not active.Off
Network Configurations
See the switch software configuration guide for network configuration concepts and examples of using the
switch to create dedicated network segments and interconnecting the segments through Fast Ethernet and
Gigabit Ethernet connections.
Cisco Catalyst 9200 Series Switches Hardware Installation Guide
13
Product Overview
RJ-45 Console Port

Cisco Catalyst 9200 Series Switches Hardware Installation Guide
14
Product Overview
Network Configurations