Claas LEXION 8000 Installation guide

LEXION 8000 - 7000
Information and Basic Field Settings

Contents
Introduction
3
6
Introduction and Safety
Overview
Cab Controls
10
12
14
Layout
C-MOTION
CEBIS
Service Maintenance
Service Maintenance23
Settings
CEBIS Calibration
Cutterbar
Cutterbar Adjustments
Side Knife/Divider
Pre-Separation
Threshing
Separation
Cleaning
Aid
27
29
31
32
35
36
37
38
40

Losses
41 Losses
EASY
44
48
49
52
Steering
CRUISE PILOT
CRUISE PILOT Symbols
CEMOS Controls
Further information
57
58
60
Frequently Asked Questions
Wet Harvest Recommendations
Recommendations

Introduction
and safety
This guide has been produced as
a reference to operator’s training.
The aim is to aid operator’s with
familiarisation and settings of
CLAAS LEXION combine harvester.
This guide does not replace the
operator’s manual. More in depth
information is available within the
operator’s manual.
Your CLAAS combine is designed
for output and efciency but this can
only be achieved with the correct
operation and maintenance of
the machine.
Make sure you are familiar with the
operator’s manual before using
the machine.
The operator’s manual is an integral
part of the machine. It addresses the
user and contains safety relevant
information. Only procedures specied
in the operator’s manual
are safe.
Read and observe the operator’s
manual before starting work.
If you need help understanding the
content, contact your local CLAAS
Dealer.
3

Overview: Dimensions
6

7
1.
2.
3. 5.
4.
6.
11.
19.
20.
10.
14.
15.
7.
21.
22.
18.
17.16.
13.
12.

Overview: Hybrid
1. Feeder chains
2. Stone trap
3. Accelerator drum
8. Rotor
9. Return pan
4. Preconcave
5. Threshing drum
6. Main concave
10. Preparation pan
11. Fan
12. Upper sieve
13. Lower sieve
14. Grain auger
15. Returns auger
16. Chaff spreader
17. Straw chopper
18. Deector
19. Returns elevator
20. Grain elevator
7. Impeller
21. Grain tank
22. Unloading auger
8

1. Rotary button
2. Favourite Management button
3. Information button
4. Escape button
1. Reverse front attachment
2. Front attachment
3. Threshing mechanism
4. Threshing drum speed
5. Concave clearance
6. Fan speed
7. Upper sieve opening
8. Lower sieve
9. Rotor speed
10. Rotor cover plates
11. Gearshift control
12. Gearshift control
13. POWER TRAC
14. Differential lock
15. Parking brakes (No function)
16. OVERDRIVE
17. Left rape cutter drive
18. Grain tank unloading rate
19. Open grain tank cover
20. Close grain tank cover
21. FIELD SCANNER operating mode
22. Not used
23. USB socket 5 V
2.
1.
3.
4. 5. 6. 7. 8. 9. 10.
11. 13. 15. 17. 19. 21.
12. 14. 16. 18. 20. 22.
1.
2.
3. 4.
23.

Cab Controls: Layout
1. Hazard warning asher switch
2. Road travel switch
3. LED working main beam switch
1. Electric rear view mirror rotary
switch
2. Warning beacons and work light
lighting control
3. A/C MATIC control unit
4. Parking lights and drive lights
rotary switch
10
1. 2. 3.
1. 2.
3.
4.

Cab Controls: Layout
Indicator Lights
6. Urea level
7. Diesel particulate lter loading con-
dition indicator light
8. Diesel engine output reduction
9. Regeneration active exhaust
temperature high
10. 11. Diesel engine fault
12. Alternator 12V
14. Emergancy steering pump
15. Rubber tracks tension
16. Brake function
17. Alternator 12V
18. Main beam
19. Direction of machine travel to the
left
20. Trailer direction of travel
11
Indicator Stalk
1. Horn
2. Main beam/Dipped beam
3. Turn signal indicator
4. Windscreen washer pushbutton
5. Windscreen wiper rotary switch
13. Diesel engine stop
14. Emergency steering pump
15. Rubber tracks tension
16. Brake function
17. Alternator 24V
18. Main beam
19. 21. Left/Right indicator
20. Trailer direction of travel
1.
2. 3.
4.
5.
6. 7. 8. 9. 10. 11.
12. 13. 14. 15. 16. 17.
18. 19. 20. 21.

Cab Controls: C-MOTION Multifunction Lever
1. Lower reel
2. Reef forward
3. Raise reel
4. Reel reverse
5. Favourites selection up
6. Favourites selection down
7. Favourites management
14. Grain tank unloading
15. Swing out grain tank unloading tube
16. Swing in grain tank unloading tube
17. Favourite adjustment
8. AUTOPILOT ON
9. Raise front attachment
10. Cutting height control
11. Lower front attachment
12. Pre-set cutting height
13. Front attachment stop/quick stop
12
1.
5.
2. 3.
4.
6.
7.
13.
8.9.
10.
12. 11.
14.
17.
16.15.

Cab Controls: CEBIS
1. Change button
2. Secondary displays
(different displays can be
selected in user dened
displays)
3. Main menus
4. Favourites selected menu
5. Direction and 4TRAC
6. Time display
7. Coolant temperature
8. AdBlue level
9. Fuel level
10. Ground speed
11. Engine RPM
14
1.
10.
2.
3.
5.6.
11.
7. 8.
9.
4.

1. 2.
12.
11.
3.
4.
5.
8.
10.
9.
6.
7.
15

Cab Controls: CEBIS
1. Change display: eld/road
2. Crop data and jobs
3. Upper secondary display
(can be changed in user dened display)
4. Centre secondary display
(can be changed in user dened display)
5. Lower secondary display
(can be changed in user dened display)
6. Main menus
7. Quick adjustment button
8. HOTKEY adjustment
9. Direction of travel and 4TRAC
(if tted)
10. Diesel engine load
11. Outline buttons
(direct access to settings)
12. Crop type and moisture display
16

Cab Controls: CEBIS
1. Ground speed display
2. Returns meter display
3. GRAINMETER display
4. Separation throughput monitor
display
5. Cleaning throughput monitor display
6. Non-grain by GRAIN QUALITY
CAMERA display
7. Broken grain by GRAIN QUALITY
CAMERA display
8. Diesel engine capacity utilization
display
9. Limiting element (Diesel engine load)
10. Limiting element (Cleaning system)
11. Limiting element (Separation)
12. Limiting element (CRUISE PILOT)
17

18
1.
12.
2.
3. 4. 5. 6.
7.
11. 10.
9.
8.

1. Select the main menu to change 2. Select the sub menu
3. Select the operating menu 4. Select the dial
1 2
34
19