Claas TUCANO 500 Installation guide

Information and Basic Field Settings
TUCANO 500

CONTENTS
Introduction
4
6-9
Introduction and Safety
Overview
Cab Controls
10-12
13
14
17-20
Layout
MONTANA
CMOTION
CEBIS
Service Maintenance
22-24 Service Maintenance

EASY
41 Steering
Settings
26-27
28-29
30
31
32
33
34
35
36
CEBIS Calibration
Cutterbar
Cutterbar Adjustments
Side Knife/Divider
Pre-Separation
Threshing
Separation
Cleaning
Aid
Losses
38-40 Losses
Frequently Asked Questions
44 Frequently Asked
Questions
Wet Harvest Advice
45-46 Wet Harvest
Recommendations
What We Recommend
47 Recommendations

This guide has been produced as
a reference to operator’s training.
The aim is to aid operator’s with
familiarisation and settings of
CLAAS TUCANO combine harvester.
This guide does not replace the
operator’s manual. More in depth
information is available within the
operator’s manual.
Your CLAAS combine is designed
for output and efciency but this can
only be achieved with the correct
operation and maintenance of the
machine.
Make sure you are familiar with the
operator’s manual before using the
machine.
The operator’s manual is an integral
part of the machine. It addresses the
user and contains safety relevant
information. Only procedures
specied in the operator’s manual
are safe.
Read and observe the operator’s
manual before starting work.
If you need help understanding the
content, contact your local CLAAS
Dealer.
4
Introduction and Safety

6
Overview: Dimensions

7
Overview: Dimensions

8
Overview: Hybrid
4. Preconcave
Applies to machine
with APS threshing system.
1. Feeder chains
2. Stone trap
5. Threshing drum
6. Main concave
3. Accelerator drum
Applies to machine
with APS threshing system.

9
Overview: Hybrid
8. Rotor
12. Upper sieve
16. Chaff spreader
20. Grain elevator
10. Preparation pan
14. Grain auger
18. Deector
22. Unloading auger
9. Return pan
13. Lower sieve
17. Straw chopper
21. Grain tank
11. Fan
15. Returns auger
19. Returns elevator
7. Impeller

10
Cab Controls: Layout
5. Front attachment
10. Upper sieve adjustment
13. 4 TRAC engage
7. Drum speed adjustment
12. Rotor speed adjustment
15. Overdrive (MONTANA)
17. Open grain tank
1. Rotary button
2. Quick adjustment button
3. Information button
4. Escape button
1
2
3
5
6
7 8 9
14
21
15 16 19
1817 20
10 11
12 13
4
6. Threshing
11. Lower sieve adjustment
14. Diff lock engage (MONTANA)
8. Concave position adjustment
9. Fan speed adjustment
16. Left rape knife
18. Close grain tank
19. LASERPILOT left/right
20. Front attachment reverse

Cab Controls: Layout
11
EASY Losses Settings Service Maintenance Cab Controls
1. Hazard warning light
5. Air conditioner2. Road travel safety swtich
3. Fold maize picker (if tted)
1 2 3
4
5
5
4
4. Lighting panel

12
Cab Controls: Layout
1. Horn 12. Diesel engine fault
6. Turn signal right 17. Trailer indicator
7. Urea minimum level light 18. Left indicator
3. Windscreen washer 14. Park brake
9. Diesel engine output reduction 20. Main beam
11. Diesel engine fault
22. Alternator
2. Main beam 13. Not used
8. Diesel particulate lter
loading too high
19. Not used
10. Regeneration active exhaust
temperature high
21. Diesel engine serious fault
4. Windscreen wiper 15. Right indicator
5. Turn signal left 16. Not used

Cab Controls: MONTANA Layout
13
EASY Losses Settings Cab ControlsService Maintenance
1. Throttle
When [6] is pressed, the machine lowers to transport position.
When [8] is pressed, the machine is levelled horizontally and the
cutterbar is then aligned with the ground.
Tip:
6. MONTANA transport position
7. Automatic mode indicator
3. Manual right tilt 9. Radio preselected channel change
11. Receive and end call
2. Manual lower 8. MONTANA automatic switch
10. Radio volume4. Manual left tilt
5. Manual raise
1
9
2
5
4 3
6
8
7
10 11

Cab Controls: C-MOTION Multifunction Lever
14
1. Lower reel
6. Favourites selection 15. Swing out unloading tube
7. HOTKEY 16. Swing in unloading tube
3. Raise reel 12. Preset height
9. Raise front attachment fast/slow
11. Lower front attachment fast/slow2. Reel forward
8. AUTOPILOT 17. Multifunction button
10. Cutting height control
4. Reel back 13. Front attachment stop/quick stop
5. Favourites selection 14. Grain tank unload
1
2
5
4
3
6
8
9
11 10
12
13
14
15
16
17
7

EASY Losses Settings Cab ControlsService Maintenance

16
Cab Controls: Notes

17
EASY Losses Settings Cab Controls
Cab Controls: CEBIS
Service Maintenance
10
1 2
3
456
7
11 9
8
1. Change button 6. Time display
7. Coolant temperature
3. Main menus 9. Fuel level
11. Engine RPM
2. Secondary displays
(different displays can be
selected in user dened displays)
8. AdBlue level
10. Ground speed
4. HOTKEY selected menu
5. Direction and 4TRAC

18
Cab Controls: CEBIS
1 2
89
15
13
12 11
14
16
6
7
3
4
5
10
1. Change display: eld/road
6. Main menus
8. HOTKEY adjustment
9. Direction of travel and 4TRAC
(if tted)
3. Upper secondary display
2. Crop data and jobs
11. Cleaning throughput monitor
13. Returns monitor
15. Outline buttons
direct access to settings
14. Ground speed
16. Crop type and moisture display
10. Diesel engine load
12. Separation throughput monitor
4. Centre secondary display
(can be changed in user
dened display)
5. Lower secondary display
(can be changed in user
dened display)
7. Quick adjustment button

19
EASY Losses Settings Cab Controls
Cab Controls: CEBIS
Service Maintenance
How to change settings in CEBIS:
1. Select the main menu to change
2. Select the sub menu
3. Select the operating menu
4. Select the dial
5. Use the slider (or)
6. The dial (or)
7. Double tap the dial
8. Type in the value

20
Cab Controls: CEBIS
1
2 3 4 5 6 7 8
How to adjust combine settings in CEBIS:
1. Tap the appropriate area here,
then adjust:
2. Front attachment
3. Threshing mechanism
4. Separation settings
5. Cleaning settings/system
6. Fan speed
7. Sieve settings (and)
8. Crop settings
9. To adjust the settings the other way,
use switches (9) and (10).
910