PRONAR T740 User manual

INTRODUCTION
Information contained herein is current at date of publication. As a result of improvements,
some numerical values and illustrations contained in this publication may not correspond to the
factual specification of the machine supplied to the user. The manufacturer reserves the right to
introduce design changes in machines produced that facilitate operation and improve the quality
of their work, without making minor amendments to this Operator's Manual.
This Operator's Manual is an integral part of the machine's documentation. Before using the
machine, the user must carefully read this Operator's Manual and observe all
recommendations. This guarantees safe operation and ensures malfunction free work of the
machine. The machine is designed to meet obligatory standards, documents and legal
regulations currently in force.
The manual describes the basic safety rules and operation of Pronar T740 trans-shipment
trailer. If the information contained in the Operator's Manual needs clarification then the user
should refer for assistance to the sale point where the machine was purchased or to the
Manufacturer.
MANUFACTURER'S ADDRESS:
PRONAR Sp. z o.o.
ul. Mickiewicza 101A
17-210 Narew
CONTACT TELEPHONES
[phone] [phone]
[phone] [phone]

SYMBOLS APPEARING IN THIS OPERATOR'S MANUAL
Information, descriptions of danger and precautions and also recommendations and prohibitions
associated with user safety instructions are marked:
and also preceded by the word "DANGER”. Failure to observe the instructions may endanger
the machine operator's or other person's health or life.
Particularly important information and instructions, the observance of which is essential, are
distinguished in the text by the sign:
and also preceded by the word "ATTENTION". Failure to observe the instructions may lead to
damage to the machine as a result of improper operation, adjustment or use.
In order to focus the user's attention on the need to perform maintenance, the relevant section
of the Operator's Manual is marked with the pictogram:
Additional tips and advice for machine operation are marked:
and also preceded by the word „TIP”.

DIRECTIONS USED IN THIS OPERATOR'S MANUAL
Left side – side to the left hand of the operator facing in the direction of machine's forward
travel.
Right side – side to the right hand of the operator facing in the direction of machine's forward
travel.

TABLE OF CONTENTS
1BASIC INFORMATION 1.1
1.1 IDENTIFICATION 1.2
1.1.1 IDENTIFICATION OF TRANS-SHIPMENT TRAILER 1.2
1.1.1 AXLE IDENTIFICATION 1.3
1.2 INTENDED USE 1.4
1.3 FITTINGS 1.6
1.4 WARRANTY CONDITIONS 1.7
1.5 TRANSPORT 1.8
1.5.1 TRANSPORT ON VEHICLE 1.8
1.5.2 INDEPENDENT TRANSPORT BY THE USER 1.10
1.6 ENVIRONMENTAL HAZARDS 1.10
1.7 WITHDRAWAL FROM USE 1.11
2SAFETY IN USE 2.1
2.1 BASIC INFORMATION CONCERNING SAFE OPERATION OF THE
MACHINE 2.2
2.2 SAFETY DURING REPAIR AND MAINTENANCE WORK 2.3
2.3 DANGERS DURING TRANS-SHIPMENT WORK 2.5
2.4 HITCHING, UNHITCHING 2.6
2.5 SAFETY PRINCIPLES WHEN WORKING WITH TYRES 2.6
2.6 DANGERS DURING TRAVEL 2.7
2.7 OPERATION OF ARTICULATED TELESCOPIC SHAFT 2.8
2.8 SAFETY TIPS FOR HYDRAULIC CLUTCH OPERATION 2.10
2.9 DESCRIPTION OF MINIMAL RISK 2.11
2.10 INFORMATION AND WARNING STICKERS 2.12

3 CONSTRUCTION AND PRINCIPLE OF OPERATION 3.1
3.1 SPECIFICATION 3.2
3.2 CHASSIS 3.3
3.2.1 DRAWBAR EYE 3.5
3.2.2 TRAILER SUPPORT 3.5
3.3 LOAD BOX 3.7
3.4 FRONT CONVEYOR 3.9
3.5 FRONT CHAIN TRANSMISSION 3.11
3.6 FRONT GEAR WHEEL TRANSMISSION 3.13
3.7 REAR CHAIN TRANSMISSION 3.14
3.8 WORKING BRAKE 3.15
3.9 PARKING BRAKE 3.20
3.10 TURNING INTERLOCK HYDRAULIC SYSTEM 3.21
3.11 HYDRAULIC SYSTEM SLIDE BOLT AND CONVEYOR 3.22
3.12 HYDRAULIC CLUTCH SYSTEM 3.24
3.13 ELECTRIC LIGHTING SYSTEM 3.27
3.14 ELECTRIC WEIGHING SYSTEM INSTALLATION 3.29
4 CORRECT USE 4.1
4.1 PREPARING FOR WORK BEFORE FIRST USE 4.2
4.2 ATTACHING TO TRACTOR 4.5
4.3 TRANS-SHIPMENT TRAILER SUPPORT OPERATION 4.7
4.4 LOADING 4.9
4.5 SECURING LOAD 4.10
4.6 TRANSPORTING THE TRAILER 4.11
4.7 UNLOADING 4.13
4.8 DISCONNECTING FROM TRACTOR 4.15

4.9 PROPER USE AND MAINTENANCE OF TYRES 4.16
4.10 WEIGHER OPERATION 4.17
4.10.1 MOUNTING INDICATOR 4.17
4.10.2 STANDARD WORK 4.18
5 TECHNICAL MAINTENANCE 5.1
5.1 PRELIMINARY INFORMATION 5.2
5.2 TRANS-SHIPMENT TRAILER SERVICE INSPECTION 5.2
5.2.1 OPERATION NO. 1 - INSPECTION OF WHEEL AXLE BEARINGS 5.5
5.2.2 OPERATION NO. 2 - REGULATION OF MAIN BRAKE 5.6
5.2.3 OPERATION NO. 3 - REGULATION OF PARKING BRAKE. 5.8
5.2.4 OPERATION NO. 4 - DRAINING WATER FROM THE AIR TANK 5.9
5.2.5 OPERATION NO. 5 - CLEANING DRAIN VALVE 5.10
5.2.6 OPERATION NO. 6 - INSPECTION OF CONNECTIONS 5.11
5.2.7 OPERATION NO. 7 – INSPECTION OF BRAKING SYSTEM ACTION 5.11
5.2.8 OPERATION NO. 8 – INSPECTION OF BRAKING SYSTEM TIGHTNESS 5.12
5.2.9 CLEANING THE AIR FILTERS 5.13
5.2.10 OPERATION NO. 10 – INSPECTION OF HYDRAULIC SYSTEM TIGHTNESS 5.14
5.2.11 OPERATION NO. 11 - INSPECTION OF LIGHTING AND SIGNALLING SYSTEM. 5.15
5.2.12 OPERATION NO. 12 - INSPECTION OF TIGHTNESS OF WHEELS AND
DRAWBAR NUTS AND BOLT CONNECTIONS 5.16
5.2.13 OPERATION NO.9 - INSPECTION OF GREASING POINTS 5.17
5.2.14 OPERATION NO. 14 - TECHNICAL INSPECTION OF WHEELS 5.25
5.2.15 OPERATION NO. 15 - REGULATION OF CLUTCH WORKING PRESSURE 5.25
5.2.16 OPERATION NO. 16 – INSPECTION OF TIGHTNESS OF FRONT CHAIN
GEARING (I STAGE) 5.27
5.2.17 OPERATION NO. 17 – INSPECTION OF TIGHTNESS OF FRONT CHAIN
TRANSMISSION (II STAGE) 5.28
5.2.18 OPERATION NO.18 – INSPECTION OF TIGHTNESS OF REAR CHAIN
TRANSMISSION 5.30
5.2.19 OPERATION NO. 19 – CHANGE OIL IN FRONT GEAR WHEEL TRANSMISSION 5.31

5.2.20 OPERATION NO. 20 – CHANGE OIL IN CONVEYOR INTERSECTING AXIS
GEARING 5.32
5.3 UNLOADING SPEED REGULATION 5.34
5.3.1 ROOF HEIGHT REGULATION 5.34
5.3.2 REGULATION OF CHANNEL SLIDES IN GRAIN TANK 5.35
5.4 CONSUMABLES 5.37
5.4.1 HYDRAULIC OIL 5.37
5.4.2 GREASES 5.38
5.5 HYDRAULIC CLUTCH OPERATION 5.38
5.5.1 SAFETY ADVICE FOR HYDRAULIC CLUTCH CLEANING AND MAINTENANCE 5.38
5.5.2 MOUNTING, MAINTENANCE AND CARE ADVICE 5.38
5.5.3 TIGHTENING TORQUE FOR NUT AND BOLT CONNECTIONS 5.39
5.5.4 SERVICE INSPECTION PERIODS 5.39
5.6 THOROUGH LOAD TANK CLEANING 5.40
5.7 CLEANING TRANS-SHIPMENT TRAILER 5.40
5.8 STORAGE 5.42
5.9 TIGHTENING TORQUE FOR NUT AND BOLT CONNECTIONS 5.42
5.10 LIST OF BULBS 5.44
5.11 FAULTS AND MEANS OF REMEDYING THEM 5.44

1.1
SECTION
1BASIC INFORMATION
IDENTIFICATION
INTENDED USE
FITTINGS
WARRANTY CONDITIONS
TRANSPORT
ENVIRONMENTAL HAZARDS
WITHDRAWAL FROM USE

1.2
1.1 IDENTIFICATION
1.1.1 IDENTIFICATION OF TRANS-SHIPMENT TRAILER
FIGURE 1.1 Location of the data plate and serial number
(1) data plate, (2) serial number
The trailer is marked with the data plate (1), located on the right frame brace and the factory
number (2) located on a gold painted rectangle. When buying the trailer check that the serial
numbers on the machine agree with the number written in the WARRANTY BOOK, in the
sales documents and in the OPERATOR'S MANUAL.