Clarke CMFT250 Installation and operation manual

OPERATING & MAINTENANCE
INSTRUCTIONS
Model No. CMFT250
PART NO: 6462200
GC0514
MULTI FUNCTION TOOL KIT

2
Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]
INTRODUCTION
Thank you for purchasing this CLARKE Mutli Function Tool Kit.
Before attempting to use the machine, please read this manual thoroughly
and follow the instructions carefully. In doing so you will ensure the safety of
yourself and that of others around you, and you can look forward to your
purchase giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for its intended purpose.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL PROTECTION
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general
household waste. It must be disposed of according to the laws governing
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal
facility.

3
Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]
TABLE OF CONTENTS
INTRODUCTION ..................................................................................2
GUARANTEE ........................................................................................2
ENVIRONMENTAL PROTECTION .........................................................2
TABLE OF CONTENTS ..........................................................................3
GENERAL SAFETY RULES ..................................................................... 4
ELECTRICAL CONNECTIONS .............................................................. 7
CONTENTS ..........................................................................................8
BEFORE USE .........................................................................................10
OPERATION .........................................................................................11
MAINTENANCE ...................................................................................14
CONSUMABLE SPARE PARTS ..............................................................14
FAULT FINDING ................................................................................... 15
SPECIFICATION ...................................................................................16
COMPONENT PARTS ...........................................................................17
DECLARATION OF CONFORMITY.......................................................19

4
Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]
GENERAL SAFETY RULES
WORK AREA
1. Keep the work area clean and well lit. Cluttered and dark areas invite
accidents.
2. Do not operate power tools in explosive atmospheres such as in the
presence of flammable liquids, gasses or dust. Power tools create sparks
which may ignite dust or fumes.
3. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
1. Power tools must match the power outlet. Never modify the plug in any
way. Do not use adaptor plugs with earthed (grounded) power tools.
Correct plugs and outlets will reduce the risk of electric shock.
2. Do not expose power tools to rain or wet conditions. Any water entering
power tools will increase the risk of electric shock.
3. Do not abuse the electrical cable. Never use the cord for pulling or
unplugging the power tool. Keep the cable away from sources of heat, oil,
sharp edges or moving parts. Damaged or tangled cables increase the
risk of electric shock.
4. When operating a power tool outdoors, use an extension cable suitable
for outdoor use. Using the correct cable reduces the risk of electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when you
are operating a power tool. Do not operate a power tool when you are
tired, ill or under the influence of alcohol, drugs or medication.
2. Wear personal protective equipment including eye protection. Safety
equipment such as a dust mask, non-skid shoes or hearing protection used
for appropriate conditions will reduce personal injuries. Use a face or dust
mask if operation is particularly dusty. Wear ear protectors/defenders as
the noise level of this machine can exceed 85dB (A). If working at floor
level, always wear knee pads.
3. Always hold the tool firmly with both hands for maximum control. Keep
proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
4. Avoid accidental starting of the machine. Ensure the switch is in the off
position and the locking button disengaged before plugging the machine
in to the power supply. Carrying power tools around with your finger on
the trigger or plugging in power tools that are switched on invites
accidents.

5
Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]
5. Dress properly. Do not wear loose clothing or jewellery which may get
caught in moving parts. Wear protective hair covering to contain long
hair. For best footing, wear rubber soled footwear. Keep floor clear of oil,
scrap wood, etc.
6. Concentrate on the job in hand, no matter how trivial it may seem. Be
aware that accidents are caused by carelessness due to familiarity.
7. Switch the machine OFF immediately after the task is completed.
POWER TOOL USE AND CARE
1. Do not force the machine. Use the correct power tool for your application.
It will do a better and safer job at the rate for which it was designed.
2. Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and
must be repaired.
3. Disconnect the power tool from the power supply before making any
adjustments, changing accessories, or storing the tool. These measures will
reduce the risk of the power tool starting accidentally.
4. Store power tools out of the reach of children and do not allow persons
unfamiliar with these instructions to operate the power tool. Power tools
are potentially dangerous in the hands of untrained users.
5. Maintain power tools in top condition. Keep tools/ machines clean for the
best and safest performance. Check for misalignment or binding of
moving parts, broken parts, or any condition that may affect the power
tool’s operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
6. Use recommended accessories. The use of improper accessories could be
hazardous.
7. Machine cleanliness. Do not allow the ventilation slots in the machine to
become blocked with dust.
8. Check the power tool for damage before using the machine. Any
damaged part should be inspected to ensure that it will operate properly
and perform its intended function. Check for alignment of moving parts,
breakage of parts, mountings, and any other condition that may affect
the machine’s operation. Any damage should be properly repaired or the
part replaced. If in doubt, DO NOT use the machine. Consult your dealer.
SAFETY RULES FOR OSCILLATING SAWS & SANDERS
1. Hold power tools by insulated gripping surfaces when performing an
operation where the cutting tools may contact hidden wiring. Contact
with a “live” wire will make exposed metal parts of the tool “live” and
shock the operator. Do not cut or break into existing walls or other blind
areas where electrical wiring may exist. If this situation is unavoidable,
disconnect all fuses or circuit breakers feeding this worksite.

6
Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]
2. Use a metal detector to determine if there are gas or water pipes hidden
in the work area or call the local utility company for assistance before
beginning the operation. Striking or cutting into a gas line will result in
explosion. Water entering an electrical device may cause electrocution.
3. Keep hands away from cutting area. Do not reach under the material
being cut. The proximity of the blade to your hand is hidden from your
sight.
4. Do not use dull or damaged blades. Bent blades can break easily or
cause kickback.
5. Exercise caution when handling the accessories. The accessories are very
sharp.
6. Wear protective gloves when changing cutting accessories. Accessories
become hot after prolonged usage.
7. Limit the exposure time to vibration by taking frequent rest periods.
Vibration caused by the tool may be harmful to the hands and arms.
8. Before scraping, check the workpiece for nails. If found, either remove
them or set them well below intended finished surface. Striking a nail with
accessory edge could cause the tool to jump.
9. Do not wet sand with this tool. Water entering the motor housing is an
electrical shock hazard.
10. Never work in area which is wet or damp such as newly applied
wallpaper. There is an electrical shock hazard when working in such
conditions with a power tool and heating of the water caused by
scraping action may cause harmful vapours to be emitted from
workpiece.
11. Always wear eye protection and a dust mask for dusty applications and
when sanding overhead. Sanding particles can be absorbed by your eyes
and inhaled easily and may cause health complications.
12. Use special precautions when sanding chemically pressure treated
lumber, lead-based paint, or any other material that may contain
carcinogens. A suitable breathing respirator and protective clothing must
be worn by persons entering the work area. The work area should be
sealed by plastic sheeting and persons not protected should be kept out
until work area is thoroughly cleaned.
13. Do not use sandpaper intended for larger sanding pads. Larger
sandpaper will extend beyond the sanding pad causing snagging, tearing
of the paper or kick-back. Extra paper extending beyond the sanding pad
can also cause cuts.
Please keep these instructions in a safe place for future reference.

7
Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]
ELECTRICAL CONNECTIONS
WARNING! Read these electrical safety instructions thoroughly
before connecting the product to the mains supply.
Before switching the product on, make sure that the voltage of your
electricity supply is the same as that indicated on the rating plate. This
product is designed to operate on 230VAC 50Hz. Do not connect it to any
other power source.
This product may be fitted with a non-rewireable plug. If it is necessary to
change the fuse in the plug, the fuse cover must be refitted. If the fuse cover
becomes lost or damaged, the plug must not be used until a suitable
replacement is obtained.
If the plug has to be changed because it is not suitable for your socket, or
due to damage, it should be cut off and a replacement fitted, following the
wiring instructions shown below. The old plug must be disposed of safely, as
insertion into a mains socket could cause an electrical hazard.
WARNING! The wires in the power cable of this product are
coloured in accordance with the following code:
Blue = Neutral Brown = Live
If the colours of the wires in the power cable of this product do not
correspond with the terminal markings of your plug, proceed as follows.
• The wire which is coloured Blue must be connected to the terminal which
is marked N or coloured Black.
• The wire which is coloured Brown must be connected to the terminal
which is marked L or coloured Red.
Plug must be BS1363/A approved.
Always fit a 5 Amp fuse.
Neutral Live
(Blue) (Brown)
Ensure that the outer sheath of the cable is firmly held by the clamp
We strongly recommend that this product is connected to the mains supply
via a Residual Current Device (RCD).
If in doubt, consult a qualified electrician. DO NOT attempt repairs yourself.
This symbol indicates that this is a Class II product and does not require
an earth connection.

8
Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]
CONTENTS
When unpacking, check for damage or shortages etc. Any found should be
reported to your CLARKE dealer where the appliance was originally
purchased. The CMFT250 Multi function tool kit is supplied with the following
components:
1. 1 x Retaining Disc
2. 1 x Retaining Screw
3. 1 x Semi Circular Cutting Blade
4. 1 x Scraper Blade
5. 1 x Side Handle
6. 1 x Straight Cutting Blade
7. 3 x Sanding Sheets - 60, 120 & 240 grit
8. 1 x Sanding Pad
9. 1 x Hexagon Key
7
8
1
2
3 4 5 6 9

9
Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]
BEFORE USE
WARNING: ENSURE THAT THE TOOL IS SWITCHED OFF AND UNPLUGGED
FROM THE MAINS SUPPLY BEFORE FITTING OR REMOVING THE
ACCESSORIES OR HANDLE.
FITTING THE SIDE HANDLE
1. If required, screw the side handle
onto the body of the tool.
NOTE: The handle can be fitted for
left or right handed use as
required. Choose the most
appropriate position for user
comfort and the task in
hand.
FITTING THE ACCESSORIES
The multi-function tool should be
supplied with the retaining disc held
in place by the retaining screw.
NOTE: The drive spindle has four
accessory locating pins as
shown.
1. Remove the retaining screw using
the hex key supplied, and lift
away the retaining disc.
2. Position your chosen accessory
on the drive spindle, ensuring that
the locating pins engage with the
corresponding holes in the
accessory and that the accessory
lays flat on the spindle.
3. Replace the retaining disc,
ensuring that the flat face is in
contact with the accessory, and
secure in place with the retaining
screw.
NOTE: All accessories are fitted in this way.
Accessory
locating pins
Retaining disc
Drive Spindle
Retaining screw

10
Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]
4. Tighten the retaining screw in a
clockwise direction using the hex
key supplied. Do not overtighten.
FITTING THE SANDING SHEETS
The sanding pad is faced with hook and loop material enabling the sanding
sheets to be quickly and simply attached or removed.
1. Align the sanding sheet to the
sanding pad and press firmly to
attach in place.
• Try to ensure that the holes in the
sanding sheet line up with the
holes in the sanding pad.
2. To remove the sanding sheet,
carefully peel off the sheet from
one of the corners.

11
Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]
Speed control
thumbwheel
On/Off Switch
OPERATION
1. Hold the tool firmly and switch on by
sliding the On/Off switch forward.
The motor will then run continuously.
Slide the switch back and the motor
will stop. (Fig. 1)
2. Adjust the speed control to the
desired working speed by turning
the thumb-wheel at the rear of the
machine. (Fig. 2)
3. Slowly apply the tool to the
workpiece and proceed to sand or
cut. Move the tool across the work
applying a light even pressure.
• Whether cutting, scraping or
sanding, always ensure the
workpiece is securely fixed, i.e.
clamped to a workbench or
secured in a vice.
• When working on car bodywork, the
vibration may cause any items left
on the car bonnet, boot or roof to fall, leading to injury to yourself or others
in the work vicinity. Always keep the work area tidy.
WARNING: ENSURE THAT THE WORKING POSITION ADOPTED DOES NOT
CAUSE OPERATOR FATIGUE WHICH MAY LEAD TO LOSS OF CONTROL.
USING THE SANDER ATTACHMENT
In sanding mode, the tool can be used to sand materials such as wood,
plastic, metal and painted surfaces.
WARNING: ALWAYS WEAR EYE PROTECTION AND A DUST MASK FOR
DUSTY APPLICATIONS AND WHEN SANDING OVERHEAD.
Ensure you have the correct sanding paper for the application. Always test
on scrap material before using on your final workpiece.
CHOOSING THE CORRECT SANDING SHEET
The sanding sheets are rated according to the number marked on the back
of each sheet. The lower the number, the coarser and more abrasive the
particles on the sheet will be.
Fig. 1
Fig. 2

12
Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]
Very coarse grit (e.g.40) is used for removing paint and sanding down rough
surfaces.
Medium grit (e.g.80) is used for sanding down plain timber.
Fine grit (e.g.120) is used to give a smooth finish to bare wood.
Very fine grit (400 & above) is used for fine sanding between coats of paint.
SANDING
1. Taking care that the sander is not
touching the work piece, switch
the tool on. Adjust the speed
control to the desired setting for
the task.
2. Place the tool on the workpiece,
ensuring the whole are of the
sanding base/pad is in contact
with the work surface.
3. Allow the tool to do the work and
do not apply heavy pressure.
Heavy pressure does not increase
the removal of material but may
wear out the sanding sheets
faster.
4. If sanding into corners, use the tip
or corner of the sanding pad.
NOTE: The sanding pad must be
kept flat on the workpiece.
Take care not to tilt the base
and use the edge of the pad. This will damage the sanding sheet
and pad, making it harder to grip the sanding sheet.
NOTE: Take care not to apply excessive pressure as this can cause
circular tooling marks on the work, especially if using coarse
sanding sheets.
USING THE SAW ATTACHMENTS
In sawing mode, the tool can be used to cut materials such as wood, plastics
and sheet metal such as aluminium, although the supplied blades are not
ideally suited to cutting steel or similar ferrous metals.
CAUTION: CLAMP YOUR WORKPIECE SECURELY IF POSSIBLE BEFORE
STARTING WORK.
Note: Ensure the blade is sharp and not damaged before starting work.

13
Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]
SAWING WITH THE STRAIGHT OR SEMI CIRCULAR BLADES
1. Switch the tool on before it
touches the work piece.
2. Adjust the speed control to the
desired setting for the task. Select
a high speed for sawing.
3. If making a plunge cut use a slight
pendulum motion to allow chip/
debris removal.
NOTE: If using the saw attachments
for plunge cuts, only use the
saw on soft materials such as
softwood and plaster boards.
Always check that there are
no nails or screws in the
workpiece before cutting.
USING THE SCRAPER
In scraping mode, the tool can be used to remove materials such as paint,
sealant residues, adhesives, fabrics and vinyl from materials such as wood,
plastic, metal and painted surfaces.
1. Switch the tool on before it
touches the work piece.
2. Adjust the speed control to a
medium/high speed as required.
3. Place the tool on the workpiece,
ensuring the angle of the scraper
blade to the workpiece is correct.
4. Allow the tool to do the work and
do not apply a heavy pressure
which can cut into the surface
and overload the tool.
NOTE: The scraping blade is designed for scraping soft materials from
flat surfaces. Ensure you get the correct angle and only apply
light pressure to avoid cutting the surface.
NOTE: The scraper blade is quite sharp and tends to remove the surface
from soft materials such as timber (acting in a similar way to a
chisel). Great care should therefore be taken when removing
coatings from these types of materials.

14
Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]
MAINTENANCE
Before starting any cleaning or maintenance, always ensure the tool is
isolated from the electrical supply by switching off and removing the plug
from the power socket.
BEFORE USE
1. Always inspect the tool before use and ensure it is in top condition.
2. Ensure all fixing screws remain tight to ensure the tool is in safe working
condition.
3. Inspect the power cable to ensure it is sound and free from damage.
CLEANING
1. Ensure all air ventilation slots are clear, (Use compressed air to clean the
tool if possible. Always wear protective goggles when cleaning with
compressed air).
2. Clean the exterior of the tool with a soft cleaning cloth. Never use any
chemicals or harsh abrasives. Avoid using solvents when cleaning plastic
parts, which may be susceptible to damage from various types of
commercial solvents.
GENERAL MAINTENANCE
• All bearings etc, in this tool are lubricated with a sufficient amount of high
grade lubricant for the tools lifetime under normal operating conditions,
therefore no further lubrication is necessary.
• The carbon brushes in the tool will eventually wear down to such an
extent that sparks will be noticed inside the tool and its performance will
deteriorate. Brushes are a consumable spare which should be replaced
by your Clarke dealer or power tool repairer.
• Refer to your CLARKE dealer if internal maintenance is required.
CONSUMABLE SPARE PARTS
The Multi-Function Tool Accessory Kit - (Part No
6462202) includes the following and is available from
your CLARKE dealer. This includes:
2 x 32 mm Straight Blade
1 x 20 mm Straight Blade
1 x Grout Removing Disc
1 x Semi-Circular Saw Blade

15
Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]
Problem Possible Cause Remedy
Tool will not operate. No power supply. Check supply and rectify
as necessary.
Switch is faulty. Consult your Clarke dealer.
Fuse blown. Check and replace if
necessary.
Motor is faulty. Consult your Clarke dealer.
Motor runs but tool
accessory does not
move.
Accessory fastening not
engaged.
Re-fit accessory correctly.
Drive gear broken. Consult your Clarke dealer.
Heavy internal sparking. Faulty motor or warn brushes. Consult your Clarke dealer.
Motor becomes hot. Unduly heavy use. Reduce the force applied to
the tool. Let the tool do the
work.
Air vents have become
blocked.
Clean out the air vents using
compressed air or clean
with a dry cloth.
Low supply voltage. Ensure supply voltage is
correct. If an extension cable
is used, ensure it is of the
correct rating and is fully
unwound.
Excessive vibration. Machine bearings worn. Consult your Clarke dealer.
FAULTFINDING

16
Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]
Please note that the details and specifications contained herein, are correct
at the time of going to print. However, CLARKE International reserve the right
to change specifications at any time without prior notice.
metI noitacificepS
ekortSfohtgneLmm8.3
etuniM/sekortS00012-00051
elgnAtibrOseerged2.3
thgieWtcudorPgk86.2
)thgieHxh
tdiWxhtgneL(snoisnemiDmm201x691x333
ycneuqerF&egatloVgnitarepOzH05/V042-032
ssalCnoitalusnIlacirtcelEIIssa
lC
gnitaResuFA5
rewoPtupnIdetaRW052
)gnidnas(noitarbiVm233.3nahtsseL
2
leveLerusserPdnuoSL AW )A(Bd4.28
leveLrewoPdnuoSL
AW )A(Bd4.39
seirosseccA
daPgnidnaS
epytdaPgnikcaB metsys'pooL&kooH'htiwremyloP
snoisnemiDmm19x19x19
edalBreparcS
)TxWxL(
snoisnemiD mm59.0x)egde(05x)latot(37
edalBgnittuCthgiartS
)TxWxL(snoisnemiDmm6.0x23x09
hteeTforebmuN32
edalB
gnittuCralucriCimeS
ssenkcihT&retemaiDmm56.0x78
hteeTforebmuN021
SPECIFICATIONS

17
Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]
COMPONENT PARTS

18
Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]
oN oNtraP noitpircseD oN oNtraP noitpircseD
110052TFMCTHwercSxeH1212052TFMCTHgnisuoHrotoM
220052TFMCTHrehsaWtalF2222052TFMCTHhctiwSffO/nO
330052TFM
CTHdaPgnidnaS3232052TFMCTHdoRtcAhctiwS
440052TFMCTHeldnipSevirD4242052TFMCTH)riap(hsurBnobraC
550052TFMCTHgniRgnil
aeS5252052TFMCTH)riap(redloHhsurB
660052TFMCTHpilcriC6262052TFMCTH)riap(eveelSreppoC
770052TFMCTHgniraeBllaB7272052
TFMCTHniPrebbuR
880052TFMCTHetalPgnitcennoC8282052TFMCTHwercS
990052TFMCTHgniraeBeldeeN9292052TFMCTHhtaehSelbaC
0101
052TFMCTHgnisuoHevirD0303052TFMCTHelbaCrewoP
1111052TFMCTHwercS1313052TFMCTHdraoBtiucriC
2121052TFMCTHgniraeB2323052
TFMCTHlebaL
3131052TFMCTHgniR-O3333052TFMCTHrevoCraeR
4141052TFMCTHgnisuoHgniraeB4343052TFMCTHwercS
5151052TFMCTHgnir
aeBllaB5353052TFMCTHyeKnellA
6161052TFMCTHelffaB6363052TFMCTHreparcS
7171052TFMCTHerutamrA7373052TFMCTHedalBthgiartS
8181052TFMCTHgniraeBllaB8383052TFMCTHedalBralucriC-imeS
9191052TFMCTHwercS9393052TFMCTHpmalCelbaC
0202052TFMCTHrota
tS0404052TFMCTHeldnaHyrallixuA
COMPONENT PARTS

19
Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]
DECLARATION OF CONFORMITY