Clarke METALWORKER CDP201B Manual

0307
SERIAL No....................

When disposing of this product, do not dispose of with general waste. It must be disposed of according to law
at a recognised disposal facility.
2

INTRODUCTION
Thank you for purchasing your CLARKE 13mm Drill Press.
Before attempting to operate the machine, please read this instruction manual
thoroughly, and follow all directions carefully. By doing so you will ensure the safety
of both yourself and others around you, and at the same time, you should look
forward to long and trouble free service from your Clarke Drill Press.
GUARANTEE
This product is guaranteed against faults in manufacture for 12 months from date
of purchase. Keep your receipt as proof of purchase. This guarantee is invalid if the
product has been found to have been abused or tampered with in any way, or not
used for the purpose for which it was intended. The reason for return must be
clearly stated. This guarantee does not affect your statutory rights.
TABLE OF CONTENTS PAGE
Safety Precautions........................................................................... 4
Additional Safety Rules for Drill Presses .......................................... 5
Electrical Connections and Wiring Diagram ................................ 6
Preparation for Use .......................................................................... 7
Description of Parts.......................................................................... 8
Assembly .......................................................................................... 9
Settings and Adjustments ............................................................. 11
Drill Speed Table ............................................................................ 12
Operation ....................................................................................... 13
Maintenance ................................................................................. 14
Cutting Speed Chart ..................................................................... 15
Trouble Shooting ............................................................................ 16
Specifications ................................................................................. 17
Optional Accessories .................................................................... 17
Parts Lists and Diagrams......................................................... 18 - 21
Personal Notes ............................................................................... 22
Spare Parts & Servicing ................................................................. 23
3

GENERAL SAFETY PRECAUTIONS
WARNING
As with all machinery, there are certain hazards involved with their operation
and use. Exercising respect and caution will considerably lessen the risk of
personal injury. However, if normal safety precautions are overlooked, or
ignored, personal injury to the operator, or damage to property may result.
1. KNOW YOUR MACHINE. Read the manual carefully. Learn the machines applications
and limitations, as well as the specific potential hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working order.
3. EARTH ALL MACHINES. If the machine is equipped with three-pin plug, it should be
plugged into a three-pin electrical socket. Never remove the earth pin.
4. REMOVE ALL ADJUSTING KEYS AND WRENCHES. Before starting, form the habit of
checking to ensure that keys, wrenches and tools are removed from the machine.
5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
6. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use machinery in damp or wet
locations, or expose them to rain. Keep work area well lit.
7. MAKE WORKSHOP CHILDPROOF - with padlocks, master switches etc.
8. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe
distance from work area
9. DON’T FORCE THE MACHINE. It will do the job better and safer, at the rate for which it
was designed.
10. USE THE RIGHT TOOL. Don’t force a tool or attachment to do a job for which it was not
designed.
11. WEAR PROPER APPAREL. Loose clothing, gloves, neckties, rings, bracelets, or other
jewellery may get caught in moving parts. Nonslip footwear is recommended. Long
hair should be contained.
12. USE SAFETY GLASSES. Everyday eyeglasses only have impact resistant lenses, they are
NOT safety glasses.
13. USE EAR DEFENDERS.
14. DON’T OVERREACH. Keep proper footing and balance at all times.
15. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
16. ALWAYS DISCONNECT THE MACHINE before servicing or changing accessories.
17. CHECK FOR DAMAGE. If part of the machine (eg. A cover or guard), is damaged, it
should be carefully inspected to ensure that it can perform its’ intended function
correctly. If in doubt, the part should be renewed. Damage to moving parts or major
components should be Inspected by a qualified technician before operating the
machine. Contact your local dealer for advice.
4

5
19. DO NOT STAND ON THE MACHINE. Serious injury could occur if the machine is tipped
over. Do not store materials above or near the machine such that it is necessary to
stand on the machine to get to them.
20. NEVER operate a machine when under the influence of alcohol, drugs or medication.
21. ALWAYS ENSURE THAT ADEQUATE LIGHTING is available. A minimum intensity of 300 lux
should be provided. Ensure that lighting is placed so that you will not be working in your
own shadow.
ADDITIONAL SAFETY RULES FOR DRILL PRESSES
WARNING:
THIS MACHINE MUST NOT BE MODIFIED, OR USED FOR ANY PURPOSE OTHER
THAN THAT FOR WHICH IT IS DESIGNED.
1. IMPORTANT: You should not operate this machine unless you are thoroughly familiar
with drilling machines and drilling techniques. If there is any doubt whatsoever, you
should consult a qualified person.
2. Do not operate the machine until it is completely assembled, and you have read, and
understood this entire manual
3. Ensure the proper electrical regulations are followed, and that the machine is properly
earthed.
4. Before switching the machine ON, ALWAYS:-
a. Ensure all chuck keys, spanners and wrenches are removed from the machine.
b. Examine the setup carefully, ensuring that the workpiece is perfectly secure.
c. Ensure your clothing is properly adjusted.
5. Make all adjustments with the power OFF.
6. Always use the correct drilling speeds for the drill size, and the type of material being
drilled (see page 15).
7. NEVER leave the drill unattended whilst it is running. Turn the machine OFF and do not
leave until it has come to a complete stop.
8. When you have finished with the machine, always remove and store the drill bits.
9. CAUTION: This Drill Press is designed for use with Drill Bits and Morticing attachments
ONLY. The use of other cutting tools or accessories could be hazardous.
10. ALWAYS use clamps, or a drill vice bolted to the table, to hold the work. It should NEVER
be held in bare hands.

ELECTRICAL CONNECTIONS
Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply through an
approved 13 amp BS 1363 plug, or a suitably fused isolator switch.
WARNING! THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in the mains lead are coloured in accordance with the following
code:
Green & Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the flexible lead of this appliance may not correspond with the coloured
markings identifying terminals in your plug proceed as follows:
Connect GREEN & YELLOW cord to terminal marked with a letter “E” or Earth symbol
“ ” or coloured GREEN or GREEN & YELLOW.
Connect BROWN cord to terminal marked with a letter “L” or coloured RED.
Connect BLUE cord to terminal marked with a letter “N” or coloured BLACK.
If this appliance is fitted with a plug which is moulded onto the electric cable (i.e. non-
rewirable) please note:
1. The plug must be thrown away if it is cut from the electric cable. There is a danger of
electric shock if it is subsequently inserted into a socket outlet.
2. Never use the plug without the fuse cover fitted.
3. Should you wish to replace a detachable fuse carrier, ensure that the correct
replacement is used (as indicated by marking or colour code).
4. Replacement fuse covers can be obtained from your local dealer or most electrical
stockists.
5. The fuse in the plug must be replaced with one of the same rating (13 amps) and this
replacement must be ASTA approved to BS1363.
WIRING DIAGRAM
6

PREPARATION
On receipt, carefully unpack the components, ensuring that no damage was suffered in
transit, and that all parts are accounted for.
The following loose items are to be found in the packing case.
A. Table Assy.
B. Column Assy.
C. This Manual
D. Box of loose parts
Loose Items in Box and Bag
E. Base.
F. Head Assy.
G. 1 X Bag of loose parts.
H. Chuck Guard Assy.
Check the parts against the above list and refer to the diagrams below.
Should there be any deficiencies or damage, please contact your CLARKE dealer
immediately .
7

8
DESCRIPTION OF PARTS
Remove all traces of preservative from the components with paraffin or a good quality
solvent, and wipe all parts thoroughly with a clean dry cloth. Apply a coating of wax paste
or light oil, to the table, column and base, to prevent rust.
Take the necessary precautions when lifting components, considering their weight.
Assistance will be required.
Before use, the machine must be securely bolted to the floor, or, to a strong, heavy
workbench of sufficient height so that you do not need to bend your back to perform
normal operations.
Ensure the location is adequately lit, and that you will not be working in your own shadow.

ASSEMBLY
CAUTION!
ASSISTANCE MUST BE USED WHEN ASSEMBLING THIS MACHINE.
Fig. 1
Fig. 3
A. Column to the Base.
Bolt the column assembly to the base with the four M10 x
40mm hex. screws provided.
NOTE: Ideally - the base, with column attached, should be
firmly bolted to the floor or workbench prior to the assembly
of other components.
Check to ensure the column securing set screws, at the
column support, are tight.
B. Table to Column.
1. Thread the Table Support Locking Handle (see Fig. 7),
into the Table Support from the left hand side, and
leave it loose at this stage.
2. Slide the Table Support with Table, over the Column
and lower it so that it rests against the column support
bracket (Fig. 1). Nip up the locking handle to prevent
the table from swinging freely during the
assembly process.
C. Head to Column.
NOTE: I t may be necessary to unscrew the Head Lock Set
Screws, (A -Fig.2), to ensure they do not protrude internally,
as this would prevent the head from sliding fully into
position.
1. With assistance, raise the Head and locate it on top of
the Column, ensuring it slides home fully.
2. Align the head with the base and tighten down the
Head Lock Set Screws using the wrench provided.
3. Locate the three feed handles, and screw them firmly
into the hub of the feed shaft Fig.3.
Fig. 2
D. Chuck Guard Assembly
Slide the Chuck Guard over the Quill Shaft and nip up the
pinch bolt, temporarily, with the pinch bolt facing the front,
(see Fig. 4). Ensure the Quill Shaft/Spindle is at the top of its
travel.
NOTE: This operation should be carried out before the chuck
is installed.
9

E. Installing the Chuck.
1. Slide the table up the column and secure it to within 6"
of the spindle.
2. Open the jaws of the chuck to their maximum, using
the chuck key supplied.
3. Put a piece of scrap wood on to the table to protect
the chuck nose.
4. Ensuring all parts are thoroughly clean, dry, and burr
free, place the chuck over the end of the spindle, and
pull the spindle down using the feed handles, pressing
the chuck jaws hard against the piece of scrap wood
until the chuck is forced home. (Fig.4).
5. Turn Chuck Guard through 180° and tighten pinch bolt.
Fig. 4
1. Undo the Belt Tension Locking
Screws (one either side of the
head - A Fig. 5), and turn the
Belt Tension Lever (B - Fig. 5),
clockwise to bring the Motor
Pulley closer to the Spindle
Pulley which will allow the belts
to be slipped on with ease.
2. Lubricate the Idler Pulley Pivot
shaft with light grease and
locate in its’ mounting between
the Motor and Spindle Pulleys.
3. Consult the chart inside the belt cover (duplicated on page 12), and fit the belts in the
position corresponding to spindle/drill speed required.
4. Turn the Belt Tension Lever (B) anti-clockwise so that tension is applied to the belts.
Tension is correct when the belts deflects by approx. ½” at their centres of run when
using reasonable thumb pressure. Lock the motor in this position with the Locking
Screws - A.
NOTE:
1. The idler pulley will ‘float’ so that tension is applied equally to both belts
2. If the belt should slip whilst drilling, adjust the belt tension.
CHECKING THE OPERATION OF THE MICROSWITCH
IMPORTANT:
When closing the cover, check the operation of the Microswitch. It is important that it
operates immediately the cover is pulled open, in order to prevent the machine from
operating........NOT when the cover is opened sufficiently for fingers to be inserted.
If necessary, bend the actuating tab, which is attached to the cover, to ensure this.
Fig.5
F. Fitting the Drive Belts.
10

Table shown tilted and swivelled
about the column
Fig. 8
Table Support
Locking Handle
Fig. 7
Table Tilt Scale
Fig. 9
1. Table.
The table may be raised, lowered or swivelled about the
column, by slackening off the Table Support Locking Handle,
(Fig.7), adjusting accordingly, and re-tightening the handle.
It may also be tilted by loosening the M16 Screw, which
secures the table to its’ mounting, beneath the table, tilting
to the required position and re-tightening the Screw.
SETTINGS and ADJUSTMENTS
A scale is provided on the
table mounting, measured
in degrees, to assist in setting
the required angle, (Fig.9)
For all normal operations,
the table should be set to 0°.
To check to ensure the table
is entirely square to the drill
bit, insert a piece of straight
round bar in the chuck,
place a square on the table and bring it up to the round
bar. Adjust the table tilt if necessary so that the table is
correctly aligned.
2. Spindle Depth. (All references are to Fig. 10)
Located around the spindle feed shaft is a Depth Stop
Collar, carrying a graduated scale (A). The collar is
capable of turning about the shaft, and may be locked
in place by a Locking Screw (B).
The graduations are imperial (inches) and metric (mm).
To set a drilling depth:
1. With the power OFF, lower the drill bit so that it contacts
the work, and hold in that position.
2. Slacken off the locking screw, and turn the collar so
that the measurement for the depth of hole required is
in line with the pointer (C). Lock the collar in this position
with the locking screw.
The drill is now set to drill holes to your pre-determined depth,
from that particular start point.
i.e. Providing the surface of your workpiece is flat and level,
you may drill a series of holes, each to the same depth.
Fig.10
11

Fig. 11
1
2
3
4
1
2
3
4
AB
SPINDLE PULLEY MOTOR PULLEY
Spindle Motor Drill Speed Spindle Motor Drill Speed
Pulley Pulley RPM Pulley Pulley RPM
AB AB
1 4 1 180 7 1 2 970
2 4 2 250 8 2 3 1280
3 3 1 300 9 3 4 1410
4 3 2 400 10 1 3 1540
5 2 1 480 11 2 4 2270
6 4 3 580 12 1 4 2740
2. Changing Drill (Spindle) Speed.
Before changing the speeds, ensure the
machine is switched OFF, and disconnected
from the mains supply.
1 Undo the Belt Tension Locking Screws (A -
Fig. 11), one either side of the head, and
turn lever B - Fig.5 clockwise to relieve any
tension on the belts. Referring to the chart
inside the belt cover (which is duplicated
below), fit the belts in the positions
corresponding to the spindle speed
required.
2. Lever the motor, on its bracket, away from the head, by turning lever B - Fig.11,
anticlockwise so that tension is applied to the belts.
NOTE: The idler pulley will ‘float’ so that tension is equally applied to both belts
Tension is correct, when the belts deflect by approx. ½” at their centre when using
reasonable pressure with the thumb and forefinger.
Lock the motor in this position using the two Locking Screws (A - Fig. 11).
NOTE: If the belt should slip whilst drilling, adjust the belt tension.
DRILL SPEED TABLE
The table below gives the belt arrangements for given drill speeds. The diagram shows the
belts fitted to A1 and B3, giving a drill speed of 1540 RPM.
A full chart is also located on the inside of the pulley cover.
12

OPERATION.
1 . Insert the drill bit into the jaws of the chuck by approx 1", ensuring that the jaws do not
touch the flutes of the drill. Before tightening the chuck, ensure that the drill is centred
within the jaws.
2. Ensure the table height and position is set so that drill travel is sufficient for the job in
hand.
3. Ensure the work is securely clamped, or, held in a drill vice, bolted to the table. Never
hold it with bare hands. Severe personal injury may be caused if the workpiece is
whipped out of the operator’s hand, and, damage to the machine incurred if the work
strikes the column.
If the piece is of irregular shape and cannot be laid flat on the table, it should be
securely blocked and clamped.
Any tilting, twisting or shifting, results not only in a
rough hole, but also increases drill breakage.
4. For small workpieces that cannot be clamped to
the table, use a Drill Press Vice. The vice must be
clamped or bolted to the table.
5. When drilling completely through wood, always
position a piece of scrap wood between the
workpiece and the table to prevent splintering on
the underside of the workpiece as the drill breaks
through. The scrap piece of wood must make
contact with the left side of the column as shown in
Fig 12. In addition, set the depth of drill travel so
that the drill cannot possibly come into contact
with the table, or, align the table so that the hole in
its’ centre is directly in line with the drill bit.
6. When completely satisfied that the setup is sound, lower the Chuck Guard into place,
and switch the machine ON, by raising the switch
cover, as shown in fig. 13, and pushing the GREEN ‘I’
button.
To switch OFF, hit the switch cover, which will push the
RED s‘O’ button, turning the machine OFF.
NOTE:
a. As a safety feature, the ON/OFF switch is a No Volt
Release type. Therefore, if the power is interrupted
whilst the machine is switched ON, it will not
automatically start when the power is restored.
b. A Micro switch is provided within the Pulley Cover,
which prevents the machine from operating unless
the Pulley Cover is firmly closed.
Fig. 12
Fig. 13
Drill Press Vices, Cross Vices and Clamps,
are available from your CLARKE dealer.
13

MAINTENANCE
For maximum performance, it is essential that the Drill Press is properly maintained. Always
inspect the machine for damage, and security of components before use. Any damage
should be repaired, and faults rectified.
If the mains lead is worn, cut or damaged in any way, it should be replaced immediately.
Please refer to the trouble shooting chart on page 16. If you are unable to rectify any faults,
please contact your local dealer or Clarke International Service Division on 020 8556 4443 for
assistance.
Monthly (When in constant use)
1. Check tightness of mounting bolts, and head and column securing set screws.
2. Check belt for wear and replace if frayed or damaged in any way.
3. Blow out any dust that may have accumulated in the motor fan.
4. Apply a thin coat of wax paste or light oil to the table and column for lubrication and
to help prevent corrosion.
Lubrication
All bearings are packed with grease at the factory and require no further lubrication.
After use
Remove all swarf from the machine and thoroughly clean all surfaces.
Components should be dry, with machined surfaces lightly oiled.
Always remove drill bits, and store in a safe place.
14

CUTTING SPEEDS
Factors which determine the best speed to use in any drill press operation are:
1. Kind of material being worked.
2. Size of hole.
3. Type of drill.
4. Quality of cut desired.
Generally, the smaller the drill, the greater the required RPM. In soft material, the
speed should be higher than for hard metals.
As a guide, the drill speed for a given drill bit size, is according to the table below.
Wood
2740 1410 -
2270 970 -1280 480 - 580 250 - 400 180
Speed Range
(RPM)
in 3/8 1/2 - - - -
mm 9.5 12.5 - - - -
Zinc in 1/4 3/8 1/2 - - -
Diecast mm 6.4 9.5 12.5 - - -
Alum & in 7/32 11/32 15/32 - - -
Brass mm 5.6 8.75 12 - - -
in 3/16 5/16 7/16 - - -
mm 4.8 7.9 11 - - -
Cast Iron in 1/8 1/4 11/32 1/2 - -
& Bronze mm 3.2 6.4 8.75 12.5 - -
Mild Steel in 3/32 5/32 1/4 3/8 1/2 -
& Malleable mm 2.4 4 6.4 9.5 12.5 -
Cast Steel in 1/16 1/8 3/16 5/16 7/16 1/2
& Med Carbon mm 1.6 3.2 4.8 7.9 11 12.5
Stainless in 3/64 1/16 1/8 1/4 3/8 1/2
and Tool Steel mm 1.2 1.6 3.2 6.4 9.5 12.5
Plastic
15

TROUBLE SHOOTING
PROBLEM
A) Incorrect belt tension
B) Dry spindle
C) Loose pulley
D) Worn bearing
A) Adjust tension
B) Remove spindle/quill assembly
and lubricate
C) Tighten pulley
D) Replace bearing
PROBABLE CAUSE REMEDY
A) Needs lubrication
B) Table lock tightened
A) Lubricate with light oil
B) Loosen clamp
Noisy
operation
(under load)
Table difficult to
raise
Excessive
drill wobble
A) Loose chuck
B) Worn spindle, or bearing
C) Worn chuck
D) Bent drill
A) Tighten by pressing chuck down
on to a block of wood against the
table.
B) Replace spindle shaft or bearing
C) Replace chuck
D) Renew Drill
Motor won’t
start
A) Power supply
B) Motor connection
C) NVR Switch connections
D) Faulty switch
E) Motor windings burned
F) Pulley Cover not closed
G) Micro Switch inoperative
A) Check power cord/fuse
B) Check motor connections
C) Check switch connections
D) Replace switch
E) Replace motor
F) Close pulley cover.
G) Check operation of micro switch,
See P10 - and renew if faulty
Drill binds
in workpiece
A) Excessive feed pressure
B) Loose belt
C) Loose drill
D) Incorrect drill speed.
E) Drill profile incorrect for
type of material
A) Apply less pressure
B) Check belt tension
C) Tighten drill with key
D) Refer to Cutting Speed chart,
and adjust drill speed accordingly
E) Consult an appropriate manual
re. Materials, Drills and Cutting
Angles, and sharpen drill
accordingly.
Drill burns
or smokes
A) Incorrect speed.
B) Chips are not discharging
C) Dull drill or incorrect profile
for material
D) Lack of coolant
E) Excessive feed pressure
A) Refer to Cutting Speed chart,
and adjust drill speed accordingly
B) Clean drill
C) As ‘E’ above
D) Use coolant whilst drilling
E) Apply less pressure
16

SPECIFICATIONS
Motor ............................................................................... 230VAC, 50Hz, 1 Phase
Power Rating ............................................ 370Watts
Current Rating .......................................... 1.8Amps
Speed ........................................................ 1400RPM
Fuse Rating ................................................................... 13Amps
No. of Speeds ................................................................. 12
Chuck Capacity ............................................................ 13mm
Spindle Taper ................................................................. JT33
Table Type ................................................................... Square - Dry
Table Dimensions ........................................................... 250x250mm
Table T- Slot Dimensions ................................................ 14x155mm
Max. Spindle Travel ........................................................ 80mm
Max. Dist. Chuck to Table (201B) ................................. 435mm
Max. Dist. Chuck to Table (251F) ................................. 745mm
Max. Dist. Chuck to Base (201B) .................................. 640mm
Max. Dist. Chuck to Base (251F) ................................... 1195mm
Column Dia.70mm.........................................................
Quill Collar Dia. .............................................................. 55mm
Dist. Column to Chuck Centre ..................................... 170mm
Overall Dimensions(201B) ............................................. 1062x330x580mm
Overall Dimensions (251F) ............................................. 1610x330x580mm
Belt Type ................................................................... M24 - 610 x2
Weight (201B) ................................................................. 52.5 kg
Weight (251F) ................................................................. 57 kg
OPTIONAL ACCESSORIES
Morticing Attachments, Mortice Chisels,
Drill Press Vices, Cross Vices (Cast Iron),
and Table Clamps
are available from your CLARKE dealer
17

HEAD ASSEMBLY
18

19
No. Description Part No.
1 Head w/pointer & trim DD13302001
2 Cable Clamp DD16102014
3 Pan Head Screw M5 3040656
4 Hex. Screw M8 30404500
5 Adjusting Lever DD16102006
6 Motor Support Rod DD16102003
7 Motor Support Rod DD16102002
8 Motor Mount DD16102007A
9 Lockwasher 12mm DDGB93-87
10 Nut Hex. M12 3040603
11 Power Cable DD13302015L
12 Cable Tie DD16102017
13 Motor DDYL7114-03
14 Hex. Nut M8 3040601
15 Washer M8 DDGB972-85
16 Motor Cable DD13302016B
17 Hex. Screw M8 DDGB5781-86
18 Belt Tension Locking Screw DD16102005
19 Belt Tension Lever DD16102004
20 Roll Pin DDGB879-86
21 Head Lock Set Screw M8 DDGB80-85
22 Depth Screw Lock DD16104012
23 Knob DD13204011
24 Feed Handle DD13304005
25 Spindle Feed Shaft DD13304000
26 Depth Stop Collar w/Scale DD13304003
27 Stop Pin DD13304010
28 Connector Wire DD13302019
29 Ext. Lockwasher 5mm DDGB8621-87
30 Pan Head Screw M5 DDGB818-85
31 No Voltage Switch DDKJD12A
32 Allen Key 4mm DDGB5356-86
33 Pan Head Screw DDGB845-85
34 Pan Head Screw M5 3040495
35 Switch Box DD13302008
36 Screw - Special Set M8 DD13302021
37 Hex. Nut M12 3040603
38 Quill Spring Cap DD16104008
39 Quill Spring DD16104009
40 Quill Spring Retainer DD16104007
41 Quill Spring Seat DD16104006
42 Lead DD13302029
HEAD ASSEMBLY PARTS LIST

20
No.Description Part No No. Description Part No.
1 Knob DD16105008 15 Spacer DD13302023
2 Idler Pivot DD16105007 16 Pulley Nut DD13302025
3 Idler Pulley DD16105006 17 Foam Washer DD13105009
4 Ball Bearing 60202 BG60202 18 Retaining Ring 11mm DDGB8941-86
5 ‘V’ Belt M24 DD16105011 19 Quill Gasket DD13303006
6 Pulley Cover w/labels DD13305000 20 Ball Bearing 60201 BRG60201
7 Motor Pulley DD16105005 21 Quill DD1302002
8 Hex Skt Screw Set M8 DDGB80-85 22 Ball Bearing 80202 BRG80202
9 Washer Head Screw 3040650 23 Spindle DD1303001
10 Pulley Insert DD13302022 24 Chuck JT33 DDJ2613
11 Pan Head Screw 3040656 25 Chuck Key DD13303010
12 Retaining Ring 17mm DDGB8941-86 26 Chuck Guard DD16108001
13 Spindle Pulley BRG60203 27 Micro switch DDXN2
14 Ball Bearing 60203 DDGB278-89 28 Micro switch Cover See dealer
PARTS LIST
PULLEY & SPINDLE
ASSY.