Clarke CIS 1212 User manual

Page 1 05_70454_0A
Instant Shed - Peak Style 12' x 12' x 8'6"
Assembly Instructions
RECOMMENDED TOOLS
OR
Clarke International
Hemnall Street
Epping
Essex CM16 4LG
ENGLAND
www.clarkeinternational.com
PARTS & SERVICE: 0208 988 7400
E-mail: [email protected] or
[email protected]
SALES: UK 01992 565333 or
EXPORT: 00 44 (0)1992 565335
Before you start: 2 or more individuals recommended for assembly, approximate time 2 hours.
Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored.
3/30/12
DESCRIPTION MODEL #
12' x 12' x 8'6"
A B C CIS 1212
3503508
Instant Shed 3.7 x 3.7 x 2.6 M - Green
C
B
A

Page 2 05_70454_0A
ANCHORING OF THE FRAME IS THE RESPONSIBILITY OF THE CONSUMER.
Clarke®International is not responsible for damage to the unit or the contents from acts of nature. Any shed that is not anchored
securely has the potential to y away causing damage. Periodically check the anchors to ensure stability of the shed. Clarke®
International cannot be responsible for any shed that blows away. NOTE: Your shed’s cover can be quickly removed and stored prior
to severe weather conditions. If strong winds or severe weather is forecast in your area, we recommend removal of cover.
PROPER ANCHORING AND INSTALLATION OF FRAME:
ATTENTION:
This shelter product is manufactured with quality materials. It is designed to t the custom fabric cover included. Please anchor the
shed carefully following the instructions in this manual. Proper anchoring, keeping cover tight and free of snow and debris is the
responsibility of the consumer. Please read and understand the installation detail, warnings and cautions prior to beginning installation.
CAUTION:
Use CAUTION when erecting the frame.
Risk of re. DO NOT smoke or use open ame devices (including grills, re pits, deep fryers, smokers or
lanterns) in or around the shed. DO NOT store ammable liquids (gasoline, kerosene, propane, etc.) in or
around your shelter. Do not expose top or sides of the shelter to open re or other ame source.
WARNING:
Choose the location of your shed carefully. DANGER: Keep away from electrical wires. Check for
overhead utility lines, tree branches or other structures. Check for underground pipes or wires before
you dig. DO NOT install near roof lines or other structures that could shed snow, ice or excessive run
off onto your shelter. DO NOT hang objects from the roof or support cables.
DANGER:
A tight cover ensures longer life and performance. Always maintain a tight cover. Loose fabric can accelerate
deterioration of cover fabric. Immediately remove any accumulated snow or ice from the roof structure with a
broom, mop or other soft-sided instrument. Use extreme caution when removing snow from cover- always
remove from outside the structure. DO NOT use hard-edged tools or instruments like rakes or shovels to
remove snow. This could result in punctures to the cover. DO NOT use bleach or harsh abrasive products to
clean the fabric cover. Cover is easily cleaned with mild soap and water.
CARE AND CLEANING:

Page 3 05_70454_0A
Quantity Part #
Corner Leg Pipe 39 1
/
2 in. / 100,3 cm
Ratchet Clamp
Corner Leg Bends
Side Bends
Steel Foot Plate
Description of Parts:
Rafter / Cross Rail 48 1
/
2 in. / 123,2 cm
Top Cross Rail 45 3
/
8 in. / 115,3 cm
Side Cross Rails, Swedge 49 3
/
4 in. / 126,4 cm
Cover Rails 46 1
/
8 in. / 117,2 cm
Washer 1
/
4 in. / 6,4 mm
Nut 1
/
4 in. / 6,4 mm
Middle Leg Pipe 49 5
/
8 in. / 126,1 cm
Half-Clamps for Middle Legs
Half-Clamps for Corner Legs
Cover
2-Zipper Door Panel
Back Panel
15 in. Anchors
Cable Clamps
Cable - 1 ft. Length
4
4
4
8
10
3
4
8
6
12
66
4
8
8
1
1
1
4
4
4
802694
802637
12270
10240
802130
801258
802129
801209
802695
01011
01010
802693
13201
13202
803076
803078
803077
Instant Shed 12' x 12' x 8' 6" - Parts List - Model # CIS 1212 3503508
10014
10016
10015 00847
}
NOTE: 15 inch anchors are available from our spare parts
department. Please quote Part No. 10014
8800938Shelter Stabiliser
8
38
10114
20
Bolts 1
/ 4x 17 / 8in. /
6,4 x 47,6 mm
Bolts 1
/ 4x 15 / 8in. /
6,4 x 41,3 mm
Bolts 1
/ 4x 2 in. /
6,4 x 50,8 mm
03032
10115
801256
801257
2
2
3-Way Top Connectors
4-Way Top Connector
2 10066White Bungee Cords (For holding door open)

Page 4 05_70454_0A
1. ASSEMBLE 2 END RIBS
2. ASSEMBLE 2 MIDDLE RIBS
12270 12270
Secure connections using Bolts as shown with #01010 Nuts.
801256
802130
802130
802130
802130
801209
801209 801209
801209
802694
802693 802693
802694
802637 802637
#10115 Bolts (15
/
8")
#10115 Bolts (15
/
8")
#03032 Bolts (17
/
8")
#03032 Bolts (17
/
8")
NOTE:
The bolt heads at
the end ribs must be facing
outward to avoid damaging
your cover.
801277

Page 5 05_70454_0A
C
C
C
3. CONNECT FRONT END RIB TO A MIDDLE RIB
A. Connect 2 Side Cross Rails (802129) at front end rib with Shelter Stabiliser (800938) as shown.
B. Connect Side Cross Rails at middle rib with Shelter Stabiliser as shown. Leave open for next rib connection.
C. Use Top Cross Rail (801258) to connect ribs at the top.
A
A
B
B
800938 800938
802129
801258
801257
801256
801258
03032
01010
801258
801258
C
01010
01010
01010
03032
10114
10114
801209
801209
802130
802129
802129
01010
03032
802129

Page 6 05_70454_0A
4. CONNECT REMAINING RIBS
A. Use 802130 Side Cross Rails and Shelter Stabiliser (800938) to connect middle ribs as shown.
B. Use 802129 Side Cross Rails and Shelter Stabiliser to connect rear end rib.
C. Use Top Cross Rail (801258) to connect ribs at the top.
802129
802129
802130
802130
801258
801258
A
C
C
B
B
A
800938
800938
01010
01010
0101010114
10114
03032
03032
801209
802129
802129
802130
801209
01010
801257
03032 01010
801258
801258

Page 7 05_70454_0A
End Rib Anchors WARNING:
Serious injury to persons
or property could result
if cover is installed and
shelter is not anchored
and is left unattended.
Shelter must be securely
anchored before use.
6. PROPERLY ANCHOR THE FRAME
A. Anchors must be placed inside shelter at the corners of the shelter.
B. Insert a ¾ inch pipe or steel rod, through the eyelet of the auger and screw the anchor into the ground until
the eyelet is sticking out of the ground by 1 to 2 inches so it can be anchored to the legs.
If ground is too hard, dig a hole with a shovel or post hole tool. Optional: Fill with cement.
C. Wrap cable provided through the eyelet of the anchor and around the frame as shown below. Secure
the cable with the clamps provided.
5. SQUARING UP THE FRAME
A. Place frame in its nal location, which needs to be as at and level as possible.
B. Measure across opposite corners. These distances must be equal to within 1 inch.
C. Check that the front and rear of the frame measures 12 feet in width
12 ft.
12 ft.

Page 8 05_70454_0A
7. DOOR PANEL AND BACK PANEL INSTALLATION
A. (1) Hold end panel at the top center with white inner surface facing inside of the shelter. (2) Wrap the edges
of the fabric panel around the end rib and line up the cross rails with the pre made slits in the fabric.
C. (1) Disconnect side cross rail from the end rib. Leave the Shelter Stabiliser attached to the rib with the bolt.
(2) Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel.
(3) Reattach the side cross rail to the end rib.
A1
C1 C2 C3
A2
B1 B2 B3
B. (1) Disconnect top cross rail (the horizontal pipe that runs from front to back along the top) from the end rib.
(2) Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel.
(3) Reattach the top cross rail to the end rib.

Page 9 05_70454_0A
PULLPULL
WEBBING
STRAP
END PANEL VIEW
FROM INSIDE
SHED
D. At the bottom, where the webbing exits the pocket on each side of end panel, pull webbing as you would a
drawstring to remove the slack. Be careful not to pull the webbing strap out of the webbing pocket.
E. Insert the “S”- Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet
and pull tight. Wind the ratchet so that the webbing overlaps itself. Position the end panel so that it is
centered on the building before fully tightening the end panel.
F. Tighten ratchets, alternating from one side to the other, until the end panel is tight. NOTE: Keep zips
fastened when tightening door panel.
D
E F
7. END PANEL INSTALLATION - continued
Insert Webbing into
Ratchet

Page 10 05_70454_0A
802695
COVER RAILS
8. INSTALLING COVER AND COVER RAILS
A. Lay the cover on the ground next to the frame with inside of the cover (the side with the pipe pockets) facing
down and the webbing on the front and rear of the corner of the building.
B. Pull cover over the frame, making sure to center cover on frame. There should be an equal amount of over-
hang at all four corners.
C. Insert the “S”- Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet
and pull tight. Wind the ratchet so that the webbing overlaps itself.
D. Disassemble cover rails and slide through fabric pockets at each leg and reattach with clamps to each leg.
Repeat this on other side. Push down on cover rails to tighten cover, before tightening bolts completely.
E. Check and tighten Ratchets and Cover Rails monthly to ensure the cover is tight.
NOTE: The Clarke®logo should
be oriented as shown below.
CORRECT
Webbing and Ratchets Securing Cover
FRONT
REAR
INCORRECT
10115
802695
13202
01011
01010
Corner
Leg
10115
802695
802695
13201
Middle
Leg
01010
01011
End Rib Cross Rail Clamps Middle Rib Cross Rail Clamps