Classic Exhibits Curved Counter Manual

11 Intro Folding Panel System
866.652.2100
1. 2. 3.
Curved Counter Set-up Instructions
Slide panel sections together. Slide U
shaped clip into holes on top & bottom of
panels to hold together. Then lay counter
top on panels. Adjust counter top by lining
panels into channels on bottom of counter
top. Use hinged panel tie to further stiffen
unit if needed.
Stand section with wing
panel on the floor and
from the rear connect
the flexible panels by
guiding the pins into the
receiving holes (align
bottom hole then top).
Slide bottom
pins in first
Repeat step one with
panel section without
wing panel.
Slide bottom
pins in first Slide panels
together
Set counter top on
while lining panels into
channels on bottom
of counter top
Optional retractable
shelf for keyboards
Slide clip into
holes on top & bottom
of panels
.
.

12 Intro Folding Panel System
866.652.2100
1. 2.
Curved Counter (fully enclosed) Set-up Instructions
Stand section with wing
panel on the floor and
from the rear connect
the flexible panels by
guiding the pins into the
receiving holes (align
bottom hole then top).
Set counter top on
while lining panels into
channels on bottom
of counter top
Optional retractable
shelf for keyboards
Repeat step one with
second set of panels and
then slide sections
together.
Slide bottom
pins in first
Slide sections
together
Slide U
hook in
top holes of
panels
to hold
together
Slide U hook in
bottom holes of
panels to hold together
Slide U
hooks into
these holes
top and
bottom
Plan View
3.
2.
1.
3.
Slide U shaped hooks into holes as shown, top
and bottom to hold unit together. Then lay the
counter top on panels. Adjust counter top by
lining panels into channels on the bottom of
counter top.
Optional Internal Shelf
Attach velcroed supports at
each corner and place shelf
on supports.

13 Intro Folding Panel System
866.652.2100
1. 2. 3.
Slide bottom
pins in first
Curved Counter Set-up Instructions
Add the channel bar between the side panels by
sliding the pins on each end of the bar into the
holes on top. Lay the counter top on panels.
Adjust counter top by lining panels into
channels on bottom of counter top.
Stand panel sections on
the floor and from the
rear connect the flexible
panels by guiding the
pins into the receiving
holes (align bottom hole
then top).
Slide bottom
pins in first
Set counter top on
while lining panels into
channels on bottom
of counter top
Set the channel bar
on by sliding the pins
into the holes on top of
the panels
Repeat step one with
flexible panels on
opposite end.

14 Intro Folding Panel System
866.652.2100
1. 2. 3.
Slide bottom
pins in first
Curved Counter (fully enclosed) Set-up Instructions
Slide U shaped hooks into holes as shown, top
and bottom to hold unit together. Then lay the
counter top on panels. Adjust counter top by
lining panels into channels on the bottom of
counter top.
Stand panel sections on
the floor and from the
rear connect the flexible
panels by guiding the
pins into the receiving
holes (align bottom hole
then top).
Set counter top on
while lining panels into
channels on bottom
of counter top
Repeat step one with
second set of panels and
then slide sections
together.
Slide U hook in
top holes of panels
to hold together
Slide U hook in
bottom holes of
panels to hold together
Slide U hooks into
these holes top and
bottom
Plan View
3.
2.
1.
Slide sections
together

15 Intro Folding Panel System
866.652.2100
If shelving unit is included, go to
OPTIONAL SHELF directions.
1. 2.
6 Panel Counter Set-up Instructions
Stand panels on the
floor and open panels
into 4-sided box with
shorter panels meeting
in back. Set counter top on with cut out to
the back where panels meet, while
lining panels into channels on
bottom of counter top.
Optional shelf
Install support on
left & right sides
Lay shelf on
top of supports
Swing shorter cut panels meet in back.
and are used as doors
Set counter top on top of
panels with cut out side to
the back, while lining panels
into channels on bottom of
counter top
Stand panels up
Configure panels into 4-sided box
OPTIONAL SHELF
Attach shelf supports to inside of
left and right side panels with
Velcro sides toward panels. Lay
shelf on top of supports. Then set
counter top on as shown in
instruction 2.

16 Intro Folding Panel System
866.652.2100
If shelving unit is included, go to
OPTIONAL SHELF directions.
1. 2.
4 Panel Counter Set-up Instructions
Stand panels on the
floor and open panels
into 3-sided U shape. Set counter top on top of panels
while lining panels into channels
on bottom of counter top.
Optional Shelf
Install support on
left & right sides
Lay shelf on
top of supports
Set counter top on top of
panels while lining panels
into channels on bottom of
counter top
Stand panels up
Configure panels into 3-sided U shape
OPTIONAL SHELF
Attach shelf supports to inside of
left and right side panels with
Velcro sides toward panels. Lay
shelf on top of supports. Then set
counter top on as shown in
instruction 2.

17 Intro Folding Panel System
866.652.2100
If shelving unit is included, go to
OPTIONAL SHELF directions.
1. 2.
4 Panel Pedestal Set-up Instructions
Stand panels on the
floor and open panels
into 4-sided box Set counter top on with cut out to
the back where panels meet, while
lining panels into channels on
bottom of counter top.
Optional Shelf
Install support on
2 sides
Lay shelf on
top of supports
Set counter top on top of
panels while lining panels
into channels on bottom of
counter top
Stand panels up
Configure panels into 4-sided box
OPTIONAL SHELF
Attach shelf supports to inside of
left and right side panels with
Velcro sides toward panels. Lay
shelf on top of supports. Then set
counter top on as shown in
instruction 2.
Swing shorter cut panel in back.
and use as door

18 Intro Folding Panel System
866.652.2100
If shelving unit is included, go to
OPTIONAL SHELF directions.
1. 2.
3 Panel Pedestal Set-up Instructions
Stand panels on the
floor and open panels
into 3-sided U shape. Set counter top on while lining
panels into channels on bottom of
counter top.
Optional Shelf
Install support on
2 sides
Lay shelf on
top of supports
Set counter top on top of
panels while lining panels
into channels on bottom of
counter top
Stand panels up
Configure panels into 3-sided U shape
OPTIONAL SHELF
Attach shelf supports to inside of
left and right side panels with
Velcro sides toward panels. Lay
shelf on top of supports. Then set
counter top on as shown in
instruction 2.