Classic Exhibits visionary DESIGNS 38907 Manual

www.classicexhibits.com
Step 1
Page 1 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #38907 -
General Layout
20’
10’
Plan View

www.classicexhibits.com
Step 2
Page 2 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #38907 - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 1
Page 1 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #38907 - Backwall Assembly
Steps:
1) Attach lower verticals [2,3,4,5] to base plates [1].
2) Attach upper verticals [2a,3a,4a,5a] to lower verticals [2,3,4,5].
3) Connect horizontals [6a,6b] and [7a,7b] together.
4) Attach horizontals [6a/6b,7a/7b] between verticals [2/2a,3/3a]
and [4/4a,5/5a] as shown.
5) Attach horizontals [8a & 9a] to verticals [3 & 3a] and
horizontals [8b & 9b] to vertical [4 & 4a] as shown.
7) Apply graphics to Velcro on back of assembled backwall.
Item Qty Description
1 4 Base Plate
2/2a 1/1 42” RR91 Vertical Extrusion
3/3a 1/1 42” RR91 Vertical Extrusion
4/4a 1/1 42” RR91 Vertical Extrusion
5/5a 1/1 42” RR91 Vertical Extrusion
6a/6b 2/2 26” Z45 Horizontal Extrusion
7a/7b 2/2 76” Z45 Horizontal Extrusion
8a/8b 1/1 39” Z45 Horizontal Extrusion
9a/9b 1/1 22.39” Z45 Horizontal Extrusion
Attach graphics
to velcro on back of
assembled backwall
Attach graphics
to velcro on back of
assembled backwall
Velcro:
Back/Top Edge
Velcro:
Back/Top Edge
Velcro:
Back/Top Edge
Velcro:
Back/Bottom Edge Velcro:
Back/Bottom Edge
Velcro:
Back/Bottom Edge Velcro:
Back/Bottom Edge
1
2
6a 6b
7a 7b
6a 6b
7a 7b
8a
8b
9a
9b
2a
3
3a
4
4a
5
5a
1
1
1

www.classicexhibits.com
Step 2
Page 2 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #38907 -
Steps:
1) Connect curved extrusions together as shown.
2) Attach verticals [10a,10b] to bottom of extrusion [11] as shown.
3) Attach verticals [10a,10b] to horizontals [8a,8b] as shown.
4) Connect horizontal [9a] to curved extrusion [13]
and horizontal [9b] to curved extrusion [15] as shown.
5) Attach graphics to backside of assembled frame.
Item Qty Description
10a/10b1/1 5.06” Z45 Vertical Extrusion
11 1 47.56” Z45 Curved Extrusion
12 1 47.56” Z45 Curved Extrusion
13 1 47.56” Z45 Curved Extrusion
14 1 47.56” Z45 Curved Extrusion
15 1 47.56” Z45 Curved Extrusion
16 1 47.56” Z45 Curved Extrusion
Attach graphics
to velcro on back of
assembled backwall
10a 10b
11
12
8a
9a
8b
9b
13
14
15
16
Backwall Circle Assembly

www.classicexhibits.com
Step 3
Page 3 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #38907 -
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Canopy Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Canopy Assembly
Steps:
1) Connect canopy pieces together as shown.
2) Apply pillow case graphic to assembled canopy
A
A
B
B
D
D
CC
Push-Button
Push button then rotate
for packing purposes

www.classicexhibits.com
Step 4
Page 4 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #38907 - Backwall Attachments
Steps:
1) Connect iPad clamshells to backwall
where indicated, as shown in detail.
Hex
Nuts
Swivel
Mounting Plate
Swivel iPad
Clamshell
Attachment
Slide connectors into groove
of extrusion. Tighten setscrew
to secure in place. Attach
monitor mount to connectors
with screws.
Bolt iPad clamshell to mounting
plate with hex nuts.
Connectors
iPad Mount
Wire
Access
iPad
Lock
Lock
*
*
*

www.classicexhibits.com
Step 5
Page 5 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #38907 -
Steps:
1) Connect horizontals [19] to verticals [17,18] inserting infills as shown.
2) Connect horizontals [19] to extrusions on backside of front panel.
3) Connect horizontals [20] between verticals [17,18] as shown.
4) Hang door on hinges as shown in detail.
5) Attach shelf supports to Velcro on inside of assembled base.
6) Place internal shelf on shelf supports.
7) Place counter top on top of assembled base.
Item Qty Description
17 1 38” S40 Vertical Extrusion w/ Door Hinge
18 1 38” S40 Vertical Extrusion w/Door Stop
19 4 18” Z45 Horizontal Extrusion
20 2 20” Z45 Horizontal Extrusion
17
19
19
19
19
20
20
18
Shelf
Support
Door
Counter Top
Shelf
Front Panel
stays assembled
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Pedestal Assembly

www.classicexhibits.com
Step 6
Page 6 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #38907 - iPad Kiosk Assembly
Lock
Infill
2
3
4
1
When assembled
*
*
Attach connector piece to tray
as shown. Then connect
assembled pamphlet
tray to vertical extrusion.
Adjustable Pamphlet Tray Attachment
Tighten Lock
to Secure
Wire
Access
iPad
Lock
Lock
Foam Lining
Removed
Home Button Shield
Optional Cover for Home Button
1) Remove foam lining from inside bottom of
clam shell as shown.
2) Attach Home Button Shield with double-sided
tape to inside of clam shell, keeping top of
shield flush with clam shell opening as shown.
NOTE: This is a permanent fix and can’t be easily
removed.
Steps:
1) Slide infill between stand verticals as shown.
2) Attach horizontal [2] between stand verticals.
3) Attach base [1] to stand verticals using bolts.
4) Attach square plate [3] to stand using bolt.
5) Attach clam shell [4] to square plate [3] using hex nuts.
6) Insert iPad and feed wire through hole.
7) Attach pamphlet trays to stand. Refer to detail.
Clam Shell
Stand
Base
Plate
Square
Plate
Hex
Nuts
Tools Required:
1) Hex Tool
2) Pliers

www.classicexhibits.com
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #38907 - Case Packing - Case 1 of 5
3a 3 2 2a
Base Plate
(2)
Base Plate
(2)
Setup Hardware
Lights
Top View of Each Level
Level 1 Level 2

www.classicexhibits.com
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #38907 - Case Packing - Case 2 of 5
8b 8a 5a 5 4a 4
6a,6a,
7a,7a
6b,6b,
7b,7b
10a,
10b
9a
9b
Connectors (3)
Connector
Graphics
Top View of Each Level
Level 1 Level 2