Classic Exhibits eco systems ECO-2041 Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
20’
ECO-2041 - 10’ x 20’ ecoSmart Inline
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Order #XXXXX
ECO Panel Install
Place ECO panel together with a vertical offset, slide down to lock
connector in place.
Panel Corner Connectors are installed just like ECO panels. Remove by
off-setting top lock clips horizontally followed by separating vertically.
ECO Panel Installation

© 2023
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation

© 2023
Crate 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
CRATE PACKING
Crate Packing

© 2023
Step 1 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Note: Velcro on horizontals [4,8]
faces back of assembly.
When assembled
Assemble frame flat on ground.
Item
1
2
3
4
5
6
7
8
Qty.
1
1
1
1
1
1
1
1
Description
88”h TSP46 Vertical Extrusion
88”h TSP46 Vertical Extrusion
50”w TSP46 Horizontal Extrusion
50”w TSP46 Horizontal Extrusion w/ Velcro
88”h TSP46 Vertical Extrusion
88”h TSP46 Vertical Extrusion
50”w TSP46 Horizontal Extrusion
50”w TSP46 Horizontal Extrusion w/ Velcro
*
Lock
Slide end of extrusion
over corner lock as shown.
Tighten setscrew
to secure extrusions
TSP46 Corner Connection
Steps:
1) Assemble verticals [1,2] between horizontals [3,4].
See TSP46 Corner Connection detail.
2) Assemble verticals [5,6] between horizontals [7,8].
See TSP46 Corner Connection detail.
1
2
3
4
5
6
7
8
****
****
FRONT VIEW
TSP Frames Assembly

© 2023
Step 2 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Infill Infill Infill
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
Qty.
6
1
1
1
1
1
1
1
1
1
1
1
1
Description
8” x 22” oval Base Plate
96”h RSG540 Vertical Extrusion
96”h RSG540 Vertical Extrusion
96”h RSG540 Vertical Extrusion
96”h RSG540 Vertical Extrusion
96”h RSG540 Vertical Extrusion
96”h RSG540 Vertical Extrusion
35”w Z41 Horizontal Extrusion
35”w Z41 Horizontal Extrusion
35”w Z41 Horizontal Extrusion
35”w Z41 Horizontal Extrusion
35”w Z41 Horizontal Extrusion
35”w Z41 Horizontal Extrusion
2
3
8
9
11
4
5
10
11
11
6
7
12
13
11
Steps:
1) Attach Base Plates [1] to bottom of verticals [2,3,4,5,6,7], using bolts.
2) Connect lower horizontals [8,10,12] between verticals [2,3], [4,5], [6,7] as shown.
3) Slide infills between verticals [2,3], [4,5], [6,7] & secure with horizontals [9,11,13].
FRONT VIEW
When assembled
Backwall Assembly

© 2023
Step 3 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
*
Insert lock into groove
of vertical extrusion;
tighten set screw to
secure connection.
TSP46
Top View
Cam Lock
Custom Cam Lock Connection Steps:
1) Connect frame assemblies together as shown, using custom cam locks.
See Custom Cam Lock Connection detail.
2) Apply SEG Graphics to front of TSP frames, as shown.
Refer to the SEG Installation general information page.
When assembled
*
*
*
*
*
*
*
*
*
*
*
*
FRONT VIEW
23
45
67
S
E
G Graphic S
E
G Graphic
1
2
56
Backwall Assembly (cont’d)

© 2023
Step 4 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Attach shelves to verticals [2,3], [4,5], [6,7] as shown.
See Shelf Attachment detail.
When assembled
Item
14A,14B
--
Qty.
12,12
12
Description
8”w Z32 Horizontal Extrusion
38.832”w x 10”d Shelf
Keep extrusions [14A,14B]
attached to underside of shelves.
14A
14B
Shelf
Shelf Attachment
Lock Setscrew
Setscrews will face
outward for ease
of assembly
*Insert locks into groove
of vertical extrusion &
tighten setscrews.
Back of Shelf
2
3
4
5
6
7
*
*
*
*
**
*
*
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
*
*
*
*
**
*
*
*
*
*
*
**
*
*
Backwall Attachments