Classic Exhibits VISIONARY DESIGNS VK-1340 Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
Perspective View
10’
10’
VK-1340 Custom Lightbox
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Order #XXXXX
CEI-110 Profile
Straight Bracket Assembly
1) Slide TWO-PIECE TS RV 4 straight bracket into
Interior Center Slot of extrusion, so that two of the
set screws are inside groove. Tighten two set screws
to secure.
3) Slide connecting extrusion over exposed ends of
bracket & connector. Tighten all remaining set screws
to secure extrusions.
2) Slide one V4 Connector into outer interior groove
of extrusion, so that one set screw is inside groove.
Tighten set screw.
TS RV 4
Bracket
V4
Insert two-piece
bracket into the
interior center slot
of extrusion.
Slide V4 Connector
into front interior
groove.
Secure inserted half of
bracket & connector
using set screws.
Slide connecting
extrusion over
exposed ends
of bracket &
connector.
Completed
Assembly
Secure extrusion,
using remaining
set screws.
Set
Screws
Straight Connection
Corner Connection
TS RV 2
Upper
Horizontal
Lower
Horizontal
Upper
Horizontal
Lower
Horizontal
TS RV 2
8 Brackets Total:
(4) - TS RV 2
(4) - A1 L-Brackets
A1
A1
Slide verticals over
brackets of lower
horizontal, then slide
upper horizontal &
brackets into grooves
& center slots
of verticals.
Completed
Assembly
Insert L-Brackets into the
Interior Center Slot & outer
interior grooves of extrusion.
Disassembly
1) Loosen set screws on brackets and slide
extrusions off of brackets.
1) Slide TWO-PIECE TS RV 2 L-bracket into
Interior Center Slot of extrusion so that two
set screws are inside groove.
Tighten two set screws to secure.
2) Slide one A1 L-Bracket into outer interior
grooves of upper and lower horizontals.
Tighten set screws to secure.
4) Slide exposed ends of installed brackets of
upper horizontal into open ends of verticals.
Tighten set screws to secure.
3) Slide vertical extrusion over exposed ends
of brackets in lower horizontal.
Tighten set screws to secure.
Corner Bracket Assembly
CEI-110 Frame Assembly
CEI110 Frame Assembly

© 2023
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation

© 2023
Crate 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
CRATE PACKING
Crate Packing

© 2023
Step 1 of 3
Order #XXXXX
Completed Assembly
1
2
3A
3B
4A
Standoffs
4B
5
Item
1
2
3A,3B
4A,4B
5
Qty.
1
1
1,1
1,1
1
Description
88”h CEI110 Vertical Extrusion
88”h CEI110 Vertical Extrusion
54”w CEI110 Horizontal Extrusion
54”w CEI110 Horizontal Extrusion
84.353”h Z140 Vertical Extrusion
Steps:
1) Connect horizontals [3A to 3B] and [4A to 4B].
See CEI-110 Straight Connection detail.
2) Attach horizontal assemblies [3A/3B] and [4A/4B] between verticals [1] and [2].
See CEI-110 Corner Connection detail.
3) Attach standoffs to vertical [5] then attach [5] between horizontal assemblies.
4) Connect lighting cords and attach transformers.
See Light to Light Connection & Light to Transformer Connection details.
CEI-110 Straight Connection
1. Insert TSRV4 Bracket into center groove &
V4 Connector into front groove of extrusion.
2. Slide Connecting extrusion over exposed
end of bracket & connector.
3. Use Set Screws to secure extrusions.
TSRV4
Bracket
(2 pieces)
V4
*
Set
Screws
CEI-110 Corner Connection
*
TSRV2
Bracket
(2 pieces)
A1
Set
Screws
1) Insert TSRV2 and A1 brackets
into grooves of extrusion.
2) Slide connecting extrusion over
exposed ends of brackets.
3) Use Set screws to secure
extrusions.
*
*
*
*
*
*
Power
Break
Power
Break
++
+
-
-
-
Lights
Male
Male
Female
Female
to power Transformer
144W / 6A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 14 lights per transformer.
Backwall Assembly

© 2023
Step 2 of 3
Order #XXXXX
5
D1 G1
D
E E1
G
*
*
*
*
*
*
*
*
Item
D/D1
E/E1
G/G1
Qty.
1/1
1/1
1/1
Description
53”w x 20“d x 4” Wood Ceiling
88”w x 20“d x 4” Wood Ceiling
53”w x 20“d x 4” Wood Ceiling
Steps:
1) Assemble wood panels as shown. See Cam Lock Connection detail.
2) Attach assembled lightbox to wood panels using washers & bolts.
3) Install SEG graphic to assemled lightbox.
See SEG Graphics Installation sheet for details.
4) Attach monitor mount to standoffs on extrusion [5] using caps.
Monitor
Mount
Caps
Standoffs
SEG Graphic
SEG Graphic
Place hex tool in hole on side of panel, then turn tool
to activate lock into connecting panel.
*Cam Lock Connection
Hex Tool
Hole Lock
Step#1 Step#2
Lock
Hex Tool
Backwall Assembly (cont’d)

© 2023
Step 3 of 3
Order #XXXXX
Transformer
Completed Assembly
Optional Lighting
to power
Steps:
1) Attach transformer. See Light to Light Connection & Light to Transformer Connection details.
2) Route cord thru hole in base of counter then connect to power.
All cords and transformer stay attached.
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
96W / 4A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 9 lights per transformer.
MOD-1563 Reception Counter