Classic Exhibits MAGELLAN DESIGNS VK-1088 User manual

www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1088 Magellan - General Layout
10‘
10‘
Plan View

www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
Using You Set-up Instructions:
The Visionary Designs Set-up Instructions for Magellan displays are created
specifically for your configuration. They are laid out sequentially, including an
exploded view of the entire display and a logical series of detailed steps for
assembly. We encourage you to study the instructions before attempting to
assemble your exhibit.
THIS IS VERY IMPORTANT!
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in red).
Cleaning & Packing Your Display:
1) Use care when cleaning aluminum extrusions or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or counter tops, use mild cleansers and
a soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing materials. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Hex Key Tool
Typical Connection Typical Connection
Most visionary design exhibits can
be assembled with the supplied Hex
Key Tool. Occasionally, a flat head
screwdriver may be required.
Detail A: Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock and creates
a strong positive connection.
Numbered
Label
Detail B: Each extrusion contains a numbered label that
corresponds to set-up instructions. The label is located
within a groove of the extrusion (when possible). Visionary
Design labels contain Black numbers unless otherwise
specified.
Horizontal Connection
Detail C: A rectangular connection bar with plastic
T Knobs is inserted between two horizontal extrusions
joined end-to-end. Turn the knobs clockwise to tighten.
Do Not Overtighten.

www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -Backwall Assembly
Part
1a/1b
2a/2b
3a/3b
4a/4b
5a/5b
Qty
1/1
1/1
1/1
1/1
1/1
Description
Base Plate
48” Curved Vertical Extrusion
48” Curved Vertical Extrusion
46.5“ Horizontal Extrusion
46.5“ Horizontal Extrusion
Steps
1) Attach lower vertical extrusions [2a,3a] to base plates [1a,1b] as shown.
2) Attach upper vertical extrusions [2b,3b] to lower vertical extrusions [2a,3a]
using connectors [a].
3) Connect horizontal extrusions [4a,4b & 5a,5b] using connectors [b].
4) Attach horizontal assemblies [4a/4b,5a/5b] between vertical assemblies as shown.
5) Apply graphic to assembled backwall.
Connect Vertical Extrusions to Base Plates by
placing lock into slot and tighten with tool.
Turn Knob Clockwise
to Tighten Lock
Do not over tighten Knobs.
Knob
Knob
Connection Piece
with Knobs
Extrusion Lock
with Knob
a
b
a
b
1a
1b
2a
2b
3a
3b
4a
4b
5a
5b
Slide connection
bar between extrusions and
tighten knobs to secure.
Connection Bar
*
*
**
*
**
**
*
Attach graphics
to velcro on back of
assembled frame

www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Attachments
Part
6/6a/6b
Qty
1/1/1
Description
Counter Support Extrusions
Steps
1) Attach graphic header to backwall with screw caps.
2) Attach back wings to back of frame with with stand-off barrles
and screw caps.
3) Attach side wings to A10 clamps at the sides of frame.
4) Lock horizontal shelf supports [6a,6b] to backwall.
5) Lock vertical shelf support [6] to horizontals and
place counter on top.
6) Attach monitor count to backwall
with screws.
6
6a
6b
Header
Counter
Top
Monitor
Mount
Side
Wings
Back
Wings
Stand-Off
Barrel
Screw
Cap
Tighten set screw to
secure A10 to extrusion.
A10 Clamp Detail
Tighten knob to secure
graphic header in place.

www.classicexhibits.com
Step 3
Page 3 of 3
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Pedestal Assembly
Part Number
7
8
9
10
11
12
12a
13
Qty
1
1
1
1
4
3
1
1
Description
39.84” Curved Vertical Extrusion
39.84” Curved Vertical Extrusion w/ A10 Clamp
39.84” Curved Vertical Extrusion w/ A10 Clamp
39.84” Curved Vertical Extrusion
17”w Horizontal Extrusion
17”w Horizontal Extrusion
17”w Horizontal Extrusion w/ Door Stopper
17”w Horizontal Extrusion w/ Door Hinge
Steps:
1) Connect front and back assemblies together using horizontals [11], placing infill between verticals and horizontals.
2) Set internal shelf on pins where indicated. ( Pins)
3) Attach wing panel to A10 clamps as shown
4) Set counter top on pedestal base.
9
10
7
8
12
11
12
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Front and Back section must remain
assembled when shipping in cases
11
11
11
13
12a
12
**
*
*
*
When desired location
is found, tighten
set screw to secure.
Tighten knob to
secure shelf in place.
Slide connector on back
of A10 clamp into groove
of extrusion.
A10 Clamp Attachment

www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Packing Instructions - Case 1 of 2
Top View
Level 1 Level 3Level 2
Wings
2a 2b 3a 3b
6a/b
6
Base Plates
(2x)
Counter
Top
4a,4b,5a,5b
Setup Hardware

www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Packing Instructions - Case 2 of 2
Top View
Level 1 Level 3 Level 4Level 2
Wing Panel
and Infills
Counter Top
Internal Shelf
11 (4x)
Front Assembly
Back Assembly