Classic Exhibits visionary designs VK-1359 Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
10’
Custom 3D Logo
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
VK-1359 - 10’ x 10’ Inline Display

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Grid View

© 2023
Order #XXXXX General Information
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED

© 2023
Crate 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
CRATE PACKING
Crate Packing

© 2023
Step 1 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
*
*
*
When assembled
A
C
D
E
B
Item
A
B
C
D
E
Qty.
1
1
1
1
1
Description
12”w x 95”h x 4”d Return Wall Panel
46”w x 95”h x 4”d Wall Panel w/ dimensional logo
12”w x 95”h x 4”d Return Wall Panel
35”w x 85”h x 4”d Backwall Panel
35”w x 85”h x 4”d Backwall Panel
Steps:
1) Assemble wall panels [A] thorugh [E] together as shown, using
roto cam locks. See Roto Cam Lock Connection detail.
*
*
*
*
*
*
*
*
*
Roto Cam Lock Connection
*
Place hex tool in hole on side of panel. Rotate
to activate lock & secure panels together.
Hole
Lock
Hex Key Tool
Step 1
Hex Key Tool
Lock
Step 2
Backwall Assembly

© 2023
Step 2 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Pergola Ceiling Assembly
(KEEP ASSEMBLED)
Place Pergola Ceiling on floor, upside down.
Attach Posts, then flip assembly to upright position.
G
F
When assembled
Item
--
F
G
Qty.
1
1
1
Description
Pergola Ceiling Assembly
2.5”w x 86.5”h Post
2.5”w x 86.5”h Post
Steps:
1) Attach Posts [F] & [G] to underside of Pergola Ceiling Assembly
using bolts as shown.
2
Place post onto beam
of Pergola assembly.
Secure post with bolts
and nuts.
1
Pergola Assembly

© 2023
Step 3 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Attach Pergola to top of backwall panels [D/E]
using Bolt to T-Nut Connection.
*Bolt to T-Nut
Connection
T-nut
bolt
****
D
E
When assembled
G
F
Pergola Attachment

© 2023
Step 4 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Shelf
BACK VIEW
Item
--
--
Qty.
4
8
Description
66.938”w x 18”d Shelf w/ Z41
19.5”w Z41 Horizontal Extrusion
Steps:
1) Insert outer extrusions through holes in backwall panels;
secure with wing nuts on back side. See Extrusion Attachment detail.
2) Slide extrusions on underside of shelves into backwall,
resting shelves on outer extrusions. Secure with wing nuts.
See Extrusion Attachment detail.
When assembled
Z41
Z41
Z41
Z41
Z41
Z41
Z41
Z41
Insert extrusion through hole in backwall;
secure with wing nut.
BACK VIEW
*
wing
nut
threaded
pin
Z41
Backwall
Extrusion Attachment
Shelf
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Shelf
Shelf
Underside view of shelves when installed
Z41 Z41
Shelf
Shelf Attachment

© 2023
Step 5 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Wire Management
Steps:
1) Secure sides of shelves to posts [F,G]
using Bolt to T-Nut Connection.
2) Connect power cords to LED Lights behind logo, under shelves
& under pergola ceiling.
*Bolt to T-Nut
Connection
T-nut
bolt
Completed Assembly
FRONT VIEW
*
*
*
*
*
*
*
*
Shelf
Shelf
F
G
Shelf
Shelf
LED Lights
LED Lights
LED Lights
LED Lights
LED Lights
Access Door
on back side
of panel
B
H
BACK VIEW
Transformer
Transformer
UNDERSIDE VIEW
bolt
T-nut
Shelf
Post
Shelf Attachment (cont’d)

© 2023
Step 6 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
No assembly is required.
BACK VIEW FRONT VIEW
Reception Counter