Classic Exhibits SACAGAWEA DESIGNS VK-2108 User manual

www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - VK-2108 - General Layout
10’
20’
Plan View

www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - General Information
Using You Set-up Instructions:
The Visionary Designs Set-up Instructions for Sacagawea displays are created
specifically for your configuration. They are laid out sequentially, including an
exploded view of the entire display and a logical series of detailed steps for
assembly. We encourage you to study the instructions before attempting to
assemble your exhibit.
THIS IS VERY IMPORTANT!
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in red).
Cleaning & Packing Your Display:
1) Use care when cleaning aluminum extrusions or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or counter tops, use mild cleansers and
a soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing materials. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Hex Key Tool Typical Connection Typical Connection
Most visionary design exhibits can
be assembled with the supplied Hex
Key Tool. Occasionally, a flat head
screwdriver may be required. Detail A: Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock and creates
a strong positive connection.
Numbered
Label
Detail B: Each extrusion contains a numbered label that
corresponds to set-up instructions. The label is located
within a groove of the extrusion (when possible). Visionary
Design labels contain Black numbers unless otherwise
specified.
Horizontal Connection
Detail C: A rectangular connection bar with plastic
T Knobs is inserted between two horizontal extrusions
joined end-to-end. Turn the knobs clockwise to tighten.
Base Plate Connection Vertical Connection Corner Connection
Detail D: Attach vertical extrusions to base
plates with supplied bolts inserted through
the hole in the plate. Be careful not to strip
the thread.
Detail E: A square connection bar with
plastic T Knobs is inserted between two
vertical extrusions joined end-to-end. Turn
the knobs clockwise to tighten.
Detail F: Plastic Star Knobs are
used to tighten locks where
horizontal extrusions connect with
vertical extrusions. Turn the knobs
clockwise to tighten. Turn counter-
clockwise to loosen, but do not
remove knob.
Do Not Overtighten.
Do Not Overtighten.
Do Not Overtighten.

www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - Backwall Assembly
indicates
location of connection
lock with knob.
Note: Slide connection
bar between extrusions and
tighten knobs to secure.
Connection Bar
a
Item
1
2a/2b
3a/3b
2c/2d
3c/3d
4a/4b
5a/5b
4c/5c
6a/6b
Description
Base Plate
42” Vertical Extrusion w/ A10 Clamps
42” Vertical Extrusion
42” Vertical Extrusion
42” Vertical Extrusion w/ A10 Clamps
45” Horizontal Extrusion
45” Horizontal Extrusion
24” Horizontal Extrusion
2.5” Angle-Cut Vertical
Qty.
4
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Steps:
1) Attach base plates [1] to lower verticals [2a,3a,2c,3c] with bolts.
2) Connect upper verticals [2b,3b,2d,3d] to lower verticals [2a,3a,2c,3c] with connection bars [b].
3) Connect horizontals [4a,4b] and [5a,5b] with connection bars [a].
4) Connect vertical assemblies [2a/2b,3a/3b,2c/2d,3c/3d] with horizontal assemblies [4a/4b,5a/5b]
and horizontals [4c,5c] as shown.
5) Connect angled verticals [6a,6b] to upper verticals as shown.
6) Attach graphics to velcro on back side of frame.
Turn Knob Clockwise
to Tighten Lock
indicates location of
knobs on BACKSIDE of unit.
Do not over tighten Knobs
Knob
Knob
3b
6b
Tighten setscrew
to secure
2.5”h Angle-Cut
Vertical Attachment
Back View of Backwall
5b
Insert connector into
groove of extrusion [3b].
Tighten setscrew
to secure.
*
Horizontal Placement
Stopper
Set upper horizontal
bar atop stopper where
indicated on verticals
Front View
Back View
a
1
1
4a
4b
5a
5b
6a
6b
*
*
Velcro:
Back/Bottom Edge
Velcro:
Back/Top Edge
Attach graphics
to velcro on back
of frame
a5a
5b
a4a
4b
3a
3b
2a
2b
2c
2d
3c
3d
6b*
6a
*
4c
5c
1
1
Velcro:
Back/Top Edge
Velcro:
Back/Bottom Edge
b
bb
b

www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea -
W
i
n
g
W
i
n
g
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Black Plastic
Set-screw
Wing Attachment
*Note: A10 clamps must
stay attached with verticals
W
i
n
g
W
i
n
g
Light Connection
Attach lights to
backwall where
desired and
tighten in place.
Steps:
1) Attach lights as indicated.
2) Attach wings to A10 clamps as shown.
3) Attach graphic signs to backwall as shown
Graphic
Cap
Standoff
Barrel
Slide connector on back of
standoff barrels into groove
of extrusion and twist to secure
in place.Secure graphic
to standoffs using screw caps.
Graphic Attachment
Counter and Wing Attachment

www.classicexhibits.com
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Case Packing Instruction
(4) Base Plates
Graphics
Halogen Lights
Setup Hardware
Top View of Each Level
Wing Panels
Level 1 Level 2 Level 3
Round Sign
A
B
Extrusions #3c&3d
Extrusions #2c&2d
Extrusions #5c
Horizontal Extrusions #4a&4b and 5a&5b
A
B
Extrusions #3a&3b
Extrusions #2a&2b
Extrusions #4c
Horizontal Extrusions #4a&4b and 5a&5b