Classic Exhibits eco systems ECO-4100 Manual

© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
20’
20’
ECO-4100 - 20’ x 20’ Display
REV 10/2022
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View

© 2022
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2022
Order #XXXXX
Assembly Assembly Cont’d
Stacking Unstacking
Stacking Assembly
1) Place one horizontal frame on top of the other, lining up the
center grooves.
2) Turn stacking lock clockwise to tighten into place. Repeat
for each lock.
Stacking Disassembly
1) Turn the stacking lock counter-clockwise to loosen.
2) The whole spring on the stacking lock should be in view to
release each frame. The disengaged spring should release
the stacking lock. If not, keep turning the stacking lock until
it disengages.
Side-by-Side Assembly
1) Frames: Place frames side-by-side with one higher than the
other, then slide panel down to lock panels securely together.
2) Corner Connectors: Repeat Step 1 for installing corner
connectors to frames.
Side-by-Side Disassembly
1) Pull pin lock outwards to disengage.
2) Pull frames upward and apart at the same time to detatch.
Push stacking lock into the slot
of the upper frame, then spin the
cap to tighten the lock.
Push pin lock into hole of connecting frame.
Note: Block of pin lock will secure in groove.
Disengage the stacking lock by
spinning the cap counter
clockwise and pulling down.
Cap
Stacking
Lock
Pin Lock
Top View
Corner Connector
SEG
Grooves
Note: Orientation of Corner
Connector may change.
Gravitee Assembly

© 2022
Order #XXXXX
Straight Connection
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
CEI152 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
Straight Connector
Straight Connector
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
CEI152 Frame Assembly

© 2022
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation

© 2022
Step 1 of 10
Order #XXXXX
Using Your Setup Instructions
The Aero Setup Instructions are created specifically for your configuration. The instructions include an
exploded view of the frame which is sequentially labeled. We encourage you to review the instructions
before attempting to assemble your exhibit.
Connections are kept very simple; no tools required. Everything assembles with push-button connectors.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Push-Button
Push-Button
66
6
6
Numbered Label
Connections are made by holding the button down and
sliding the red tube into opposing tube until button locks
into the hole of the opposing tube. To disassemble, push button
and pull or twist extrusions apart.
Locked layer contains
placeholder marks.
When assembled
Steps:
1) Assemble lower parts labeled [1] through [18] together in numerical order.
2) Assemble upper parts labeled [19] through [36] together in numerical order
3) Connect upper & lower assemblies together using (8) verticals [V].
4) Attach end pieces [1/19] & [18/36] to frame.
5) Apply Pillowcase Graphic to assembled frame.
1
3
4
5
7
8
9
10
11
12 13 14 15
16
17
18
19
V
end
piece
end
piece
V
V
V
V
VV
V
20
21
22
23
24
25
26
27
28
29
30 31 32 33
34 35
36
6
2
Aero Frame Assembly

© 2022
Step 2 of 10
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
Refer to the Gravitee Assembly general information page.
1) Assemble Gravitee posts & panels [1] through [10] together
in numerical order as shown.
Top View
Top View
Top View
Top View
When assembled
1
23
45
6
7
8
9
10
Item
1
2
3
4
5
6
7
8
9
10
Qty.
1
1
1
1
1
1
1
1
1
1
Description
38”w x 95”h lower Gravitee Panel
94.5”h lower Gravitee Corner Post w/ caps
38”w x 95”h lower Gravitee Panel
38”w x 95”h lower Gravitee Panel
94.5”h lower Gravitee Corner Post w/ caps
38”w x 95”h lower Gravitee Panel w/ Door
94.5”h lower Gravitee Corner Post w/ caps
38”w x 95”h lower Gravitee Panel
38”w x 95”h lower Gravitee Panel
94.5”h lower Gravitee Corner Post w/ caps
Lower Gravitee Tower Assembly

© 2022
Step 3 of 10
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Steps:
Refer to the Gravitee Assembly general information page.
1) Assemble Gravitee posts & panels [1] through [10] together
in numerical order, while attaching to lower panels.
2) Attach horizontal [1] between panels [3] & [9].
1
Keep internal extrusions
attached to Gravitee panels.
DO NOT REMOVE.
Item
1
2
3
4
5
6
7
8
9
10
1
Qty.
1
1
1
1
1
1
1
1
1
1
1
Description
38”w x 95”h upper Gravitee Panel w/ S44
94.5”h upper Gravitee Corner Post w/ caps
38”w x 95”h upper Gravitee Panel
38”w x 95”h upper Gravitee Panel
94.5”h upper Gravitee Corner Post w/ caps
38”w x 95”h upper Gravitee Panel w/ S44
94.5”h upper Gravitee Corner Post w/ caps
38”w x 95”h upper Gravitee Panel
38”w x 95”h upper Gravitee Panel
94.5”h upper Gravitee Corner Post w/ caps
38.5”w Z45 Horizontal Extrusion
1
23
45
6
7
8
9
10
1
23
45
6
7
8
9
10
Upper Gravitee Tower Assembly

© 2022
Step 4 of 10
Order #XXXXX
Locked layer contains
placeholder marks.
S
E
G
G
r
aphi
c
Steps:
1) Apply SEG graphics to tower assembly
as shown.
S
E
G Graphic
S
E
G Graphic
S
E
G
G
r
aphi
c
S
E
G
Doo
r
Graph
i
c
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner, then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
Tower Graphics