Classic Exhibits SEGUE DESIGNS VK-1960 Supernova User manual

© 2018
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-1960 Supernova
Plan View
Perspective View
10’
10’
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]

© 2018
Order #XXXXX Grid View
Locked layer contains
placeholder marks.
= 1 sq foot

© 2018
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2018
Order #XXXXX
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
4
13
2
Fold edges over.
Insert into
groove
of frame
SEG Installation

© 2018
Order #XXXXX
CEI-110 Profile
Straight Bracket Assembly
1) Slide TWO-PIECE TS RV 4 straight bracket into
Interior Center Slot of extrusion, so that two of the
set screws are inside groove. Tighten two set screws
to secure.
3) Slide connecting extrusion over exposed ends of
bracket & connector. Tighten all remaining set screws
to secure extrusions.
2) Slide one V4 Connector into outer interior groove
of extrusion, so that one set screw is inside groove.
Tighten set screw.
TS RV 4
Bracket
V4
Insert two-piece
bracket into the
interior center slot
of extrusion.
Slide V4 Connector
into front interior
groove.
Secure inserted half of
bracket & connector
using set screws.
Slide connecting
extrusion over
exposed ends
of bracket &
connector.
Completed
Assembly
Secure extrusion,
using remaining
set screws.
Set
Screws
Straight Connection
Corner Connection
TS RV 2
Upper
Horizontal
Lower
Horizontal
Upper
Horizontal
Lower
Horizontal
TS RV 2
8 Brackets Total:
(4) - TS RV 2
(4) - A1 L-Brackets
A1
A1
Slide verticals over
brackets of lower
horizontal, then slide
upper horizontal &
brackets into grooves
& center slots
of verticals.
Completed
Assembly
Insert L-Brackets into the
Interior Center Slot & outer
interior grooves of extrusion.
Disassembly
1) Loosen set screws on brackets and slide
extrusions off of brackets.
1) Slide TWO-PIECE TS RV 2 L-bracket into
Interior Center Slot of extrusion so that two
set screws are inside groove.
Tighten two set screws to secure.
2) Slide one A1 L-Bracket into outer interior
grooves of upper and lower horizontals.
Tighten set screws to secure.
4) Slide exposed ends of installed brackets of
upper horizontal into open ends of verticals.
Tighten set screws to secure.
3) Slide vertical extrusion over exposed ends
of brackets in lower horizontal.
Tighten set screws to secure.
Corner Bracket Assembly
CEI-110 Frame Assembly
CEI110 Frame Assembly

© 2018
Case 1 of 1
Order #XXXXX Case Packing
Top View of Each Level
Level 1 Level 2 Level 3 Level 4 Level 5
4A4
2
6 6A
Shelf
Wings
Base
Plates
35 5A
2A 3A
Shelf
Shelf
Setup Hardware

© 2018
Step 1 of 2
Order #XXXXX Backwall Assembly
1
4
Transformer
6
6A
2
3
5
5A
4A
2A
3A
1
Item
1
2,2A
3,3A
4,4A
5,5A
6,6A
Qty.
1
1,1
1,1
1,1
1,1
1,1
Description
Base Plate
45”w CEI110 Horizontal Extrusion
45”h CEI110 Horizontal Extrusion
42”h CEI110 Vertical Extrusion
42”h CEI110 Vertical Extrusion
42“h S91 Vertical Extrusion
Steps:
1) Attach base plates [1] to horizontals [2] & [3] using bolts, washers, and wing nuts.
2) Assemble horizontals [2 to 3] [2A to 3A] and verticals [4 to 5] [4A to 5A] together.
See CEI-110 Frame Assembly sheet for instruction.
3) Conect verticals [6] & [6A] together.
4) Attach vertical assembly [6/6A] to assembly [4A/5A], using bolts.
See S91 to CEI110 Attachment detail.
5) Connect lighting cords and attach transformers. See
Light to Light Connections & Light to Transformer details.
6) Install SEG graphic to front of assembled frame and blocker fabric to back.
See SEG Graphic Installation sheet for details.
*
*
*
Power
Break
Power
Break
++
+
-
-
-
Lights
Male
Male
Female
Female
to power Transformer
144W / 6A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 14 lights per transformer.
Transformer
Connector
S91
CEI110
S91 to CEI110 Attachment
*
Bolt
Slide connector into groove of S91
extrusion. Tighten set screws to secure
connector. Attach CEI110 extrusion
to S91, using bolt.
Lighting Installation Warning
Bolt Nylon
Washer
If utilizing your own hardware,
purchase nylon washers to prevent
metal screw heads from damaging
the circuit board.
Attach no more than seven lights
per chain.
Diamond
Washer

© 2018
Step 2 of 2
Order #XXXXX Backwall Attachments
6
6A
6
Completed Assembly
Monitor
Mount
Shelf
Shelf
Shelf
Steps:
1) Lock shelves to vertical [6]. See Shelf Attachment detail.
2) Attach monitor mount to vertical [6A]. See Monitor Mount Attachment detail.
3) Attach wings to top and sides, using A10 clamps. See A10 Clamp detail.
*
*
*
*
Shelf Attachment
Insert Lock into groove of vertical
extrusion and tighten Set Screw.
Lock
Set Screw
Shelf
*
Knob
Set Screw
Connector
1) Slide connector of clamp
into extrusion groove.
2) Tighten set screw when
A10 is in desired location.
3) Insert wing into clamp.
4) Tighten knob on clamp
to secure wing in place.
A10 Clamp
A10 Clamp
Monitor Mount
Connectors
*
Slide Connectors into groove
of S12. Tighten set screws
to secure Connectors in place.
Attach Monitor Mount back
plate to Extrusion, using Bolts.
Bolts
Monitor
Mount
V31/S12