Classic Exhibits VISIONARY DESIGNS VK-2959 Manual

www.classicexhibits.com
Step 1
Page 1 of 8
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2959 - General Layout
Perspective View
10’
Plan View 20’

www.classicexhibits.com
Step 2
Page 2 of 8
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 1
Page 1 of 8
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
1
2
5
6
8
7
4
3
Transformer
Power
When assembled
A
B
AB
Item
1-2
3-4
5-6
7-8
Qty.
1ea.
1ea.
1ea.
1ea.
Description
84”h TSP50 Vertical Extrusion
22”w TSP50 Horizontal Extrusion
83.75”h TSP50 Vertical Extrusion
60”w TSP50 Horizontal Extrusion
Steps:
1) Assemble TSP50 frames together as shown.
Refer to TSP50 w/ A1 L Bracket Attachment detail.
TSP50 Extrusion Profile
Back
Front
Lights
Supernova Lights
Supernova Lights
Supernova Lights
*
*
*
*
*
*
*
*
**** See attached SEG graphic
installation for graphic attachment
Transformer
Power
**Slide A1 L Bracket into TSP50
extrusion and secure with set screws.
A1
TSP50 w/ A1 L Bracket Attachment
*
Tighten set
screw to secure
A1
A1
Tighten set
screw to secure
Backwall Assembly - TSP Frames A & B

www.classicexhibits.com
Step 2
Page 2 of 8
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly - TSP Frames C & D
When assembled
C
D
Item
1-2
3-4
5-6
7-8
Qty.
1ea.
1ea.
1ea.
1ea.
Description
83.75”h TSP50 Vertical Extrusion
34”w TSP50 Horizontal Extrusion
83.75”h TSP50 Vertical Extrusion
84”w TSP50 Horizontal Extrusion
Steps:
1) Assemble TSP50 frames together as shown.
Refer to TSP50 w/ A1 L Bracket Attachment detail.
TSP50 Extrusion Profile
Back
Front
Lights
1
2
5
6
8
7
4
3
Transformer
Power
C
D
Supernova Lights
Supernova Lights
Supernova Lights
*
*
*
*
*
*
*
*
**** See attached SEG graphic
installation for graphic attachment
Transformer
Power
**Slide A1 L Bracket into TSP50
extrusion and secure with set screws.
A1
TSP50 w/ A1 L Bracket Attachment
*
Tighten set
screw to secure
A1
A1
Tighten set
screw to secure

www.classicexhibits.com
Step 3
Page 3 of 8
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Sections Assembly
Steps:
1) Attach base plates [11a] to verticals [11] and [12] with bolt as shown.
2) Attach assembled TSP frames [A,B,C,D] between verticals.
Refer to custom cam lock detail.
Item
9
10
11
11a
12
9
12
10
11
11
11a
11a
11a
Qty.
1
1
2
3
1
Description
84”h Vertical Extrusion
84”h Vertical Extrusion
83.75”h Vertical Extrusion
Oval Base Plate
83.75”h Vertical Extrusion
A
C
D
B
Top View
Cam Lock
Tighten screw to
clamp cam lock
into groove of
vertical extrusion.
Custom Cam Lock
*
*
*
**
*** * ***
*
**
* *

www.classicexhibits.com
Step 4
Page 4 of 8
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Counter Assembly
Item
12
13
14
15/15A
Qty.
1
1
2
2/2
Description
38”h Vertical Extrusion
38”h Vertical Extrusion
Curved Horizontal Extrusion
8”w Horizontal Extrusion
Steps:
1) Attach lower horizontals [14,15] between verticals [12,13] and backwall as shown.
2) Attach upper horizontals [14,15A] between verticals [12,13] and backwall as shown.
3) Attach door to vertical [13]. Refer to Door Attachment detail.
4) Attach shelf supports with velcro to inside of assembled base.
5) Place counter atop assembled base as shown.
Shelf
Shelf Supports
(Attach with velcro to inside of assembled base)
Counter
12
13
14
14
15
15A
15A
15
Door
HingeHinge
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Infill
Infill
HingeHinge
A
B

www.classicexhibits.com
Step 5
Page 5 of 8
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Attachments
ABC
ABC
16b
16a
17a
18a
17b
18b
Connect 3 piece Canopy
together by using bolts and
wing nuts provided.
Bolts
Connecting
Canopy Pieces
Together
Example of Canopy Connection
Steps:
1) Connect canopy pieces together using
bolts & wing nuts. Refer to Example of
Canopy Connection detail.
2) Assemble arched header pieces together.
3) Attach assembled header to assembled canopy.
Refer to Header Attachment detail.
4) Attach assembled canopy & header atop
assembled backwall.
5) Attach wings using A10 clamps. Refer to
Example of A10 Clamp Attachment detail.
Item
16a/16b
17a/17b
18a/18b
Item
16a/16b
17a/17b
18a/18b
Qty.
1/1
1/1
1/1
Description
5.862” Vertical Extrusion
40.319” Curved Extru.
39” Horizontal Extrusion
Attaching Graphics
Attach Header Graphic to Back of
assembled header frame.
Bolt
Wing Nut
Header Attachment
16b
16a
17a
18a
17b
18b
When desired location
is found, tighten
set screw to secure.
Tighten knob to
secure shelf in place.
Slide connector on back
of A10 clamp into groove
of extrusion.
A10 Clamp Example

www.classicexhibits.com
Step 6
Page 6 of 8
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Attachments Cont’d
Attach connector piece to
backside of Lit. Rack as
shown; connect assembly
to vertical extrusion.
Literature Rack Attachment
Tighten Lock
to Secure
*
Steps:
1) Attach graphic using standoff barrels and caps.
See Graphic Attachment detail.
2) Attach literature rack to backwall as shown.
See Literature Rack Attachment detail.
3) Attach iPad clamshell atop counter as shown.
See iPad Attachment detail.
4) Attach Monitor Mount.
See Monitor Mount Attachment detail.
Graphic
*
Bolt
Monitor Mount Attachment
Attach monitor mount to horizontal
extrusion using bolts and wing nuts.
Wing
Nut
Graphic
Cap
Standoff
Barrel
Slide connector on back of standoff
barrels into groove of extrusion
and twist to secure in place. Secure graphic
to standoffs using screw caps.
Graphic Attachment
*
Swivel
Mounting
Plate
iPad Mount Attachment
*
Hex
Nuts
Swivel
Mounting Plate
Bolt iPad clamshell to
mounting plate with hex nuts.
Attach connector to backside
of iPad Clamshell; connect
assembly to vertical extrusion
Tighten Lock
to Secure
Clam Shell rotates between
portrait and landscape
viewing modes.
Wire Access
iPad
Lock Lock
*
*
Graphic
*
*
*

www.classicexhibits.com
Step 7
Page 7 of 8
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1267 Pedestal Assembly
Item
19
20
21
21A
22
22A
23/23A
24/24A
25/25A
Qty.
1
1
1
1
1
1
1/1
1/1
1/1
Description
38”h Vertical Extrusion w/ Door Hinges
38”h Vertical Extrusion w/ Door Stop
38”h Vertical Extrusion
34.417”h Vertical Extrusion
38”h Vertical Extrusion
34.417”h Vertical Extrusion
22.0197”w Horizontal Extrusion
12.5”w Horizontal Extrusion
26.639”w Curved Horizontal Extrusion
Steps
1) Attach lower horizontal extrusions [23,24,25] between
vertical extrusions [19,20,21,22] as shown.
2) Hang assembled door on hinges on vertical [19] as shown. Refer to detail.
3) Place side and front inserts between verticals as shown.
4) Attach upper horizontal extrusions [23A,24A,25A] between
vertical extrusions [19,20,21,22] and on top of infills as shown.
5) Attach shelf supports to inside of pedestal; set internal
shelf on top of supports.
6) Place counter top on assembled pedestal.
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Door
Insert
Insert
Insert
19
20
22
22A 21
21A
23
23A
25
25A
24
24
24A
24A
Counter Top
Internal Shelf
Extrusion
w/Door
Hinges
Shelf
Supports

www.classicexhibits.com
Step 8
Page 8 of 8
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1267 Pedestal Assembly
Item
19
20
21
21A
22
22A
23/23A
24/24A
25/25A
Qty.
1
1
1
1
1
1
1/1
1/1
1/1
Description
38”h Vertical Extrusion w/ Door Hinges
38”h Vertical Extrusion w/ Door Stop
38”h Vertical Extrusion
34.417”h Vertical Extrusion
38”h Vertical Extrusion
34.417”h Vertical Extrusion
22.0197”w Horizontal Extrusion
12.5”w Horizontal Extrusion
26.639”w Curved Horizontal Extrusion
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Door
Insert
Insert
Insert
19
20
22
22A 21
21A
23
23A
25
25A
24
24
24A
24A
Counter Top
Internal Shelf
Extrusion
w/Door
Hinges
Shelf
Supports
Steps
1) Attach lower horizontal extrusions [23,24,25] between
vertical extrusions [19,20,21,22] as shown.
2) Hang assembled door on hinges on vertical [19] as shown. Refer to detail.
3) Place side and front inserts between verticals as shown.
4) Attach upper horizontal extrusions [23A,24A,25A] between
vertical extrusions [19,20,21,22] and on top of infills as shown.
5) Attach shelf supports to inside of pedestal; set internal
shelf on top of supports.
6) Place counter top on assembled pedestal.