Classic Exhibits VISIONARY DESIGNS MOD-1594 Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Shelf
Shelf
Supports Shelf
Supports Shelf
Supports
Counter Top
Graphic
Graphic
Graphic
Door Door
Infill
Infill
Infill
Infill
6
1
2
11
7
913
15
14
10
17
19
20
18
8
12 3
4
5
BACK VIEW FRONT VIEW
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
--
--
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
6
Description
38”h Q918 Vertical Extrusion
38”h Q918 Vertical Extrusion
38”h Q918 Vertical Extrusion
38”h Q918 Vertical Extrusion
38”h Q918 Vertical Extrusion
38”h Q918 Vertical Extrusion
32.155”w Z45 Horizontal Extrusion
32.155”w Z45 Horizontal Extrusion
32.155”w Z45 Horizontal Extrusion
32.155”w Z45 Horizontal Extrusion
15”w Z45 Horizontal Extrusion
15”w Z45 Horizontal Extrusion
15”w Z45 Horizontal Extrusion
15”w Z45 Horizontal Extrusion
15”w Z45 Horizontal Extrusion
15”w Z45 Horizontal Extrusion
32.155”w Z45 Horizontal Extrusion
32.155”w Z45 Horizontal Extrusion
32.155”w Z45 Horizontal Extrusion
32.155”w Z45 Horizontal Extrusion
Door
18”h Shelf Supports
Steps:
1) Assemble lower horizontals [7,9,11,13,15,17,19] between verticals [1,2,3,4,5,6].
2) Insert infills between verticals [1,2], [2,3], [3,4], [1,5].
3) Connect upper horizontals [8,10,12,14,16,18,20] between verticals [1,2,3,4,5,6].
4) Attach Doors between verticals [4,5], [5,6]. See Door Attachment detail.
5) Affix shelf supports to inside of couter assembly using Velcro; place
shelf onto shelf supports.
6) Affix Sintra Panels to outside of assembly, using Velcro.
6) Attach Counter Top to top of assembly.
When assembled
16
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
*
*
*
*
MOD-1594 Large Counter
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information