Classic Exhibits SACAGAWEA DESIGNS VK-1222 Manual

© 2019
Order #XXXXX
Locked layer contains
placeholder marks.
Top View
Perspective View
Scale: 18
10’
10’
VK-1222 General Layout
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2019
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2019
Case 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1 (Bottom Level) Level 2 Level 3
Base
Plate
10A 11
10
Assembled Header
11A
Counter
Top
Graphic
Lights
Setup Hardware
w/ Shelf
4A, 4B, 5A, 5B
2B,2A 3A,3B
A,A
Graphic
Wings
Case Packing

© 2019
Step 1 of 2
Order #XXXXX
Item
1
2A,2B
3A,3B
4A,4B
5A,5B
6A,6B
Description
Base Plate
42” Vertical Extrusion w/ Clamps
42” Vertical Extrusion w/ Clamps
45” Horizontal Extrusion
45” Horizontal Extrusion
2.5” Angle-Cut Vertical Extrusion
Qty.
2
1,1
1,1
1,1
1,1
1,1
Horizontal Placement
Stopper
Set upper horizontal extrusion
on top of stopper of verticals.
1
1
3A
3B
B
B
2A
2B
4B
4A
5B
5A
Velcro on
Back/Bottom Edge
Velcro on
Back/Top Edge
Velcro on
Back/Inside Edges
of Verticals
Connection Bar A
ACompleted Backwall Assembly
FRONT VIEW
Slide connection bar between
extrusions, then turn knobs
clockwise to tighten lock.
Straight Connection
with Knobs
Do not over tighten Knobs
Knob
Knob
Corner Connection
with Knob
Turn knob clockwise
to tighten lock.
Do not over tighten Knobs
Knob
Keep connection bars [A] attached to
[4A] [5A] and [B] to [2A] [3A].
6B
6A
Set Screw
Connector
Back View of Backwall
Insert connector into groove
of vertical extrusion, then
tighten set screw to secure.
Velcro
2.5” Angle-Cut
Extrusion Attachment
*
*
*
Keep [6A] attached to [2B] and [6B]
attached to [3B].
Velcro on extrusions
must face to BACK of
assembled Backwall.
Steps:
1) Attach base plates [1] to verticals [2A] and [3A], using bolts.
2) Connect verticals [2A to 2B] and [3A to 3B] with connection bars [B].
See Straight Connection with Knobs detail.
3) Connect horizontals [4A to 4B] and [5A to 5B] with connection bars [A].
See Straight Connection with Knobs detail.
4) Connect vertical assemblies [2A/2B] and [3A/3B] to horizontal assemblies
[4A/4B] [5A/5B]. See Corner Connection with Knob detail.
5) Attach graphic to Velcro on back of assembled Backwall.
Clamp
Keep clamps attached to [2A] [2B] [3A]
and [3B].
VK-1222 Backwall Assembly

© 2019
Step 2 of 2
Order #XXXXX
Completed Assembly
5B
2B
2A
3B
3A
5A *
*
*
Item
7/8/9
10A
10/11
11A
Description
Assembled Header Frame
Support Leg
Assembled Counter Support
Mounting Plate
Qty.
1/1/1
1
1/1
1
Steps:
1) Connect lights to [5A/5B]. See Light Connection detail.
2) Attach assembled header frame [7/8/9] to [5A/5B].
3) Attach fabric graphic to Velcro on back of assembled header.
4) Attach counter support [10/11] to [2A].
5) Attach support leg [10A] to counter support [10/11].
6) Attach shelf to extrusion [2A].
7) Attach counter to mounting plate [11A]. See Counter Attachment sheet.
8) Route USB cords from counter. See USB Cord Management sheet.
9) Attach wings to clamps on [2A/2B] and [3A/3B]. See Clamp Attachment detail.
10) Attach graphic to [3B]. See Graphic Attachment detail.
Keep [10] and [11] assembled.
Keep [7] [8] and [9] assembled.
10A
11
10
Graphic
Wing
Wing
Wing
Shelf
*
Slide light onto clip then lock clip
into groove of horizontal extrusion.
Clip
Light
Light Connection
Clip
Light
Horizontal Extrusion
Velcro on extrusions
must face to BACK of
assembled Backwall.
*
Connector
Graphic Attachment
Cap
Graphic
Standoff
Slide connector into groove of extrusion.
Tighten set screws to secure in place.
Screw standoff into connector. Place
graphic between standoff and cap then
tighten cap to secure graphic.
When desired location
is found, tighten
set screw to secure.
Slide connector, located on
back of clamp, into groove
of extrusion.
Clamp
Clamp Attachment
Keep clamps attached to verticals, when packing.
Knob
Set Screw
A10 Clamp
11A
VK-1222 Backwall Attachments