Classic Exhibits VISIONARY DESIGNS MOD-1722 Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
BACK VIEW FRONT VIEW
MOD-1722 Backlit Counter
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Order #XXXXX
Corner Connection
TS RV 2
Upper
Horizontal
Lower
Horizontal
Upper
Horizontal
Lower
Horizontal
TS RV 2
8 Brackets Total:
(4) - TS RV 2
(4) - A1 L-Brackets
A1
A1
Slide verticals over
brackets of lower
horizontal, then slide
upper horizontal &
brackets into grooves
& center slots
of verticals.
Completed
Assembly
Insert L-Brackets into the
Interior Center Slot & outer
interior grooves of extrusion.
Disassembly
1) Loosen set screws on brackets and slide
extrusions off of brackets.
1) Slide TWO-PIECE TS RV 2 L-bracket into
Interior Center Slot of extrusion so that two
set screws are inside groove.
Tighten two set screws to secure.
2) Slide one A1 L-Bracket into outer interior
grooves of upper and lower horizontals.
Tighten set screws to secure.
4) Slide exposed ends of installed brackets of
upper horizontal into open ends of verticals.
Tighten set screws to secure.
3) Slide vertical extrusion over exposed ends
of brackets in lower horizontal.
Tighten set screws to secure.
Corner Bracket Assembly
CEI-110 Frame Assembly
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Graphic
Installation
CEI110 Frame Assembly

© 2023
Case 1 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3 Level 4 Level 5 Level 6
Door
3
Counter
Top
Shelf
Shelf
9 9A
11 11A
16,
16A
17,
17A
8,8A
18,
18A 13
7A
1 2
7
19A
14 15
19 12
Infills
26,26A
Case Packing

© 2023
Case 2 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Door
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3 Level 4 Level 5
10A
4 5
10
Counter Top
25A 25
2224 20
Bracket
w/21A Bracket
w/21
Infills
23A23
Graphics
Setup Hardware
Shelf Supports
Case Packing

© 2023
Step 1 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Assemble lower horizontals [7,8,9,10] between
verticals [1,2,3,4,5].
2) Slide Infills between verticals as shown.
3) Attach upper horizontals [7A,8A,9A,10A], securing infills.
4) Connect lower horizontals [16,17,18,19] between verticals
[5,12,13,14,15].
5) Slide Infills between verticals.
6) Secure Infills with upper horizontals [16A,17A,18A,19A].
7) Connect doors to vertical [3] and [13]. See Door Connection detail.
Item
1
2
3
4
5
7,7A
8,8A
9,9A
10,10A
Qty.
1
1
1
1
1
1,1
1,1
1,1
1,1
Description
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
8.341” Z45 Horizontal Extrusion
4” Z45 Horizontal Extrusion
16.067” Z45 Horizontal Extrusion
4” Z45 Horizontal Extrusion
12
13
14
15
16,16A
17,17A
18,18A
19,19A
1
1
1
1
1,1
1,1
1,1
1,1
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
4” Z45 Horizontal Extrusion
16.067” Z45 Horizontal Extrusion
4” Z45 Horizontal Extrusion
8.341” Z45 Horizontal Extrusion
16A
16
12
13
14
15
19A
18A
17A
17
18 19
5*
*
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Connection
*
Pin
Infill
Door
*
*
1
7A 8A
9A
10A
2
3
4
5
9
8
7
10
Infill
Infill
Infill
Infill
Infill
Door
When assembled
Counter Assembly

© 2023
Step 2 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Connect vertical [22] between horizontals [23,23A], &
veritcal [24] between horizontals [25,25A]. Refer to the
CEI110 Frame Assembly general info page.
2) Attach assembled frames to verticals [1] & [15], as shown.
See Frame to Assembly Attachment detail.
3) Slide 2-part Infills into back of both assembled frames &
secure with verticals [11,26] & [11A,26A].
4) Attach horizontals [21,21A] & two brackets to vertical [20],
then attach brackets to CEI110 corners [23/25] & [23A/25A],
inserting Infill. See Z45 & Bracket Connection detail.
Item
11,11A
20
21,21A
22
23,23A
24
25,25A
26,26A
Qty.
1,1
1
1,1
1
1,1
1
1,1
1,1
Description
35.853”h Z33 Vertical Extrusion
38.752” TSP2 Vertical Extrusion
3.193” Z31 Horizontal Extrusion
39.5” CEI110 Vertical Extrusion
45.75” CEI110 Horizontal Extrusion
39.5” CEI110 Vertical Extrusion
45.75” CEI110 Horizontal Extrusion
35.853”h GS300 Vertical Extrusion
Frame to Assembly Attachment
Bolt
CEI110
S44
Connector
*
Slide Connector into S44 vertical, then
tighten set screws to secure. Attach
CEI110 vertical to Connector, using bolt.
Slide Connector into Z31 horizontal, then
tighten set screws to secure. Attach Z31
to Bracket, using bolts. Attach bracket to
CEI110 horizontal, using bolts. Slide TSP2
vertical into slot of Bracket, then
secure lock of Z31 into vertical TSP2.
Connector
Z31
CEI110
TSP2
Z31 & Bracket Connection
*
Bracket
Corner
Assembly
Infill
1
*
*
11A
26A
*
*
20
15
24
25
25A
21
21A
Bracket
Bracket
*
*
Infill
Infill
Infill
20
Bracket
Bracket
21
21A
23A
23
11
26
22 Infill
Infill
When assembled
Counter Attachments

© 2023
Step 3 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
BACK VIEWFRONT VIEW
***
**
*
**
Completed Assembly
Steps:
1) Connect lighting power cords and attach
transformers. See Light to Light Connection
and Light to Transformer Connection details.
2) Place shelves onto pins. See Shelf Pin detail.
3) Place counter top on top of assembed counter base.
See Counter Top Attachment detail.
4) Install SEG graphics to front of assembled frames.
See SEG Graphic Installation detail.
BACK VIEW FRONT VIEW
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
Shelf Pin
1) Slide pin into groove
of Vertical Extrusion.
2) Use hex tool to
tighten pin in place.
Pin
*
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
Counter Top
Counter Top
Shelf
Shelf
Transformer Transformer
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
Light to Light Connection
Light to Tranformer Connection
SEG Graphic
SEG Graphic
Counter Attachments (cont’d)