Classic Exhibits visionary VK-2098 User manual

www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Magellan MOR VK-2098 - General Layout
10’
20’ Plan View

www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
Part Number
1
2
3
4
5
6a/6b
7a/7b
Qty
2
1
1
1
1
1/1
1/1
Description
Base Plate
48.115” Lower Curved Extrusion
48.115” Upper Curved Extrusion
47”h Lower Vertical Extrusion
47”h Upper Vertical Extrusion
52.476” Horizontal Curved Extrusion
52.476” Horizontal Curved Extrusion
Steps:
1) Attach vertical extrusions to base plates [2 to 1 and 4 to 1].
2) Connect vertical pieces together [2 to 3 and 4/4a to 5/5a].
3) Connect curved extrusions together [6a to 6b and 7a to 7b].
4) Attach horizontal assembles [6a/6b and 7a/7b] between
Base Plate Attachment
1
1
Connect Vertical Extrusion to
Base Plate by placing lock
into slot and tighten with tool.
2
3
4
5
6a
7b
6b
7a
Connection
Bar
Slide Connection Bar
between Extrusions
and tighten Knobs
to secure.
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of connection bar
with knobs on BACKSIDE of unit.
Rear View of Display
**Do not over tighten Knobs.**
Knob
Knob
Graphic Attachment
Apply graphics to back
of assembled backwall.
Connection
Bar
Connection
Bar
Connection
Bar
Connection
Bar
Velcro attched to LOWER
back of extrusion bar
Velcro attched to UPPER
back of extrusion bar
GREEN STAR indicates
location of connection
lock with knob.
A
B
B
C
5a
4a
V10
Pressure Screw
Note: V10 Detail
Slide V10 in between
grooves of extrusions
#5 and 5a.
Tighten to secure.
Pressure Screw
Example of Pressure
Screw Attachment
Note: Extrusions 5/5a and 4/4a
must stay assembled when shipping.
Holes for Header Attachment

www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Holes for Header Attachment
Velcro attched to LOWER
back of extrusion bar
GREEN STAR indicates
location of connection
lock with knob.
Turn Knob Clockwise
to Tighten Lock
RED STAR indicates location of connection
bar with knobs on BACKSIDE of unit.
Rear View of Display
**Do not over tighten Knobs.**
Knob
Knob
Part Number
1
8
8a
9
9a
10
11
12a/12b
13a/13b
14
Qty
2
1
1
1
1
1
1
1/1
1/1
2
Description
Base Plate
47”h Lower Vertical Extrusion
47”h Corner Extrusion
47”h Upper Vertical Extrusion
47”h Corner Extrusion
48.115” Lower Curved Extrusion
48.115” Upper Curved Extrusion
52.476” Horizontal Curved Extrusion
52.476” Horizontal Curved Extrusion
25”w Horizontal Extrusion
Steps:
1) Attach vertical extrusions to base plates [8 to 1 and 10 to 1].
2) Connect vertical pieces together [8/8a to 9/9a and 10 to 11].
3) Connect curved extrusions together [12a to 12b and 13a to 13b].
4) Attach horizontal assembles [12a/12b and 13a/13b] between
vertical assemblies as shown.
1
1
8
9
10
11
12a
13b
12b
13a
Connection
Bar
Slide Connection Bar
between Extrusions
and tighten Knobs
to secure.
Connection
Bar
Connection
Bar
Graphic Attachment
Apply graphics to back
of assembled backwall.
A
B
B
C
Velcro attched to UPPER
back of extrusion bar
8a
9a
Note: Extrusions 8/8a and 9/9
must stay assembled when shipping.
14
14
Velcro attched to UPPER
back of extrusion bar
Velcro attched to LOWER
back of extrusion bar
Backwall Assembly (Cont’d)

www.classicexhibits.com
Step 3
Page 3 of 4
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Light, Header and Wing Attachment
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Black Plastic
Set-screw
Wing Attachment
W
I
N
G
W
I
N
G
W
I
N
G
W
I
N
G
*Note: A10 Clamps
should remain
attaced to vertical
extrusions
Light Connection
Attach Lights to
Backwall where
desired and tighten
in place.
Attach Header Signs to
Frame using Screw Caps.
Cap

www.classicexhibits.com
Step 4
Page 4 of 4
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Item
15
16
16A
17
18
19
20
21
Qty.
1
1
1
1
1
2
2
4
Steps
1) Connect lower horizontal extrusions [19 and 21] between vertical extrusions [15, 16, 17 and 18] as shown.
2) Place inserts and attach door where indicated.
3) Attach upper horizontal extrusions [20 and 21] between vertical extrusions [15, 16, 17 and 18] and atop
inserts and door.
4) Place shelf atop lip of extrusions [19].
5) Set counter top on assembled pedestal.
Description
37.50”h Vertical Extrusion
37.50”h Vertical Extrusion
Door Stop
37.50”h Vertical Extrusion
37.50”h Vertical Extrusion
Horizontal Extrusion w/ Lip
Horizontal Extrusion
Curved Horizontal Extrusion
15
16
17
18
20
20
19
21 19
Extrusions 19
have a lip for the
shelf to rest
upon. Lip
Extrusion Details:
Door
Door
Stop
Shelf
21
21
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Counter Top
16A
Door
Hinges
I
N
S
E
R
T
I
N
S
E
R
T
21
Graphic Insert
Pedestal Assembly

www.classicexhibits.com
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Case Packing Instruction - Case 1 of 4
Lights and Setups Hardware
Graphics
Level 1 Level 2
2 - Base Plates
Extrusions #2 and 3
Extrusions #6a and 6b Extrusions #7a and 7b
Backwall Components
Level 3 Slip Sheet
2 - Set of Wings
2- Extrusions #14
Extrusions #4/4a
Extrusions #5/5a
Header Graphic

www.classicexhibits.com
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Level 1 Level 2
2 - Base Plates
Extrusions #12a and 12b Extrusions #13a and 13b
Backwall Components cont’d
Extrusions #8/8a
Extrusions #9/9a
Extrusions #10 and 11
Case Packing Instruction - Case 2 of 4

www.classicexhibits.com
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Case Packing Instruction - Case 3 of 4
Level 1
Level 2
Level 3
Level 4Level 5
Assembled
Pedestal Side Assembled
Pedestal Side Pedestal Door
3A - Door Stop
4 - #7 pieces
Internal Shelf
Counter Top
MOD-1235 Components
Front Insert
8
Door Stop
4 - Horizontal Pieces

www.classicexhibits.com
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Case Packing Instruction - Case 4 of 4
Level 1
Level 2
Level 3
Level 4Level 5
Assembled
Pedestal Side Assembled
Pedestal Side Pedestal Door
3A - Door Stop
4 - #7 pieces
Internal Shelf
Counter Top
MOD-1235 Components
Front Insert
8
Door Stop
4 - Horizontal Pieces